View Event Log, View Input Status

View Status Menus

A.4.3 View Event Log

For details on this feature, see 5.3 - View Event Log.

View Event Log

EVENT LOG

Event history

SYSTEM USER LOGIN

07-MAY-02 10:29:10

DEVICE_1 HW FORCE ON CONTACT CLOSED

07-MAY-02 09:50:10

DEVICE_4 FORCE OFF CONTACT OPEN

07-MAY-02 09:20:10

DEVICE_3 AUTO

CONTACT OPEN

07-MAY-02 06:20:10

<ENTER>=MORE <ESC>=EXIT <A>=ALL

DATE AND TIME SET

06-MAY-02 07:10:10

DEVICE_4 FORCE OFF CONTACT CLOSED

07-MAY-02 06:20:10

1=REFRESH EVENT LOG 2=RETURN TO MAIN MENU

SELECT A NUMBER:

A.4.4 View Input Status

For details on this feature, see 5.4 - View Input Status.

View Input Status

INPUT STATUS

Input status from device

INPUT STATUS

DEVICE_1 NORMAL

DEVICE_2 ALARM

DEVICE_3 EVENT

DEVICE_4 ALARM

1=REFRESH INPUT 2=RETURN TO MAIN MENU

SELECT A NUMBER:1

59	Liebert® AC4™

Page 65

Image 65

Emerson AC4 user manual View Event Log, View Input Status

Contents

Liebert AC4 Page Table of Contents Setup System Setup Common Alarm 7.5 Setup System Setup Zones Setup Menu Appendix a Service Terminal Interface Figures Available Alarms Methods of Viewing and Configuring the Liebert AC4Data Logs Introduction Operation LCD for configurationOutside Enclosure Overview Device RS232 LiebertLiebert HimodHimod Typical ConfigurationDevice Liebert Challenger Controller board components Controller Board Overview DIP switch ConnectorLCD connector 24VAC power Output LEDs Status LEDs Input LEDs LED IndicatorsLED indicators summary Typical Sequence Installation Installation ConsiderationsPacking Contents Unpacking and Preliminary Inspection Mounting the Panel Surface-Mounting the Liebert AC4Required tools Flush-Mounting the Liebert AC4 Electrical connections to panel Connect Power to the Liebert AC4 Wiring specifications Wiring SpecificationsWiring and Connections Connecting Liebert Precision Cooling Units Connecting Digital Inputs and OutputsConnecting Digital Inputs Numbering keys Digital output jumper settings Connecting Digital OutputsSetting the Digital Output Jumpers RS232 Connector Connecting Common Alarm OutputsCommon alarm outputs Serial interface connector RS232/EIA5 Guide to Liebert AC4 functions Overview of Menus LCD Menu Overview Opening Screen OverviewMain Menu Overview View Status Options Active Alarms View Active AlarmsClearing Active Alarms Active Alarms Alarm Log View Alarm LogAlarm log conditions Alarm Log Event Log View Event LogEvent log conditions Event Log Input Status View Input StatusViewing Additional Input Data Digital input states Output Status View Output StatusViewing Additional Output Data Digital output states Silence Alarm Service Terminal Interface only Silence Alarm & Backup LOG Files Service Terminal Interface Back Up Log Files Service Terminal Interface only Silence Alarm & Backup Log Files Service Terminal Interface Login LoginSystem and Control Options Valid characters for data entry System & Control menu Clear Alarms&Logs selected Login ScreenSetup System menu Clear Alarms/Logs menu Setup System Setup Inputs Setup System Overview Define Input as Normally Open or Normally Closed Define Input as Alarmable or EventChange Label Name of Input Set Up Delay Time Set Up Alarmable Inputs in Latched or Unlatched ModeDelay Time Latched / Unlatched Reset Common Alarm Setup System Setup Common AlarmChange to Reset Y or Not Reset N Set Up a Zone Setup System Setup ZonesMessage if too few devices entered Message if too many devices entered Define Output as Normally Open or Normally Closed Setup System Setup Outputs Enable or Disable an Output Device in Alarm Status Define Operating or Standby ModeConfigure Output for Loss of Power Fail-Safe Set Mode Change Password Setup System Setup System InfoChange the Password Reset Password to the Factory Default Aaaa Setup Site ID Setup Site IDSet Date & Time/Automatic Daylight Saving Time Set Date & Time Backup and Upload Configuration File Back Up the Configuration File Upload the Configuration File Firmware Update Service Terminal Interface only Factory DefaultsFactory Defaults Perform Firmware UPDATE-YESY or NON? N Select Setup Operation Setup OperationSetup Operation Menu Default settings operation features Activate / Deactivate Turn Automatic Sequencing On or OffSet Interval & Start Time 1- to 99-Day Interval Set Start Time Hour Interval Change Standby Testing Turn Standby Testing On or OffSpecify Failed Standby Response Failed Standby response Hold Delay Time Specify Hold Delay TimeRestart Delay Time Setup Operation Menu Override Output Clear Active Alarms Clear Alarms & LogsClear the Alarm Log Clear the Event Log Specifications Liebert AC4 Specifications Specifications Liebert AC4 Comparison of Functions LCD and Service Terminal Interface Appendix a Service Terminal Interface Connecting to the Service Terminal Interface Specify COM Port Connection COM1 Port SetupCreate a Connection Ascii Setup Properties SetupSettings tab Ascii Setup button Click on the file name for example, AC4.ht Connect to the Service Terminal Interface Setup Menu Overview Silence Alarm and Backup Log FilesView Status Overview Main Menu For sample screens, see View Active Alarms View Active AlarmsView Status Menus Main Menu View Alarm Log View Alarm Log View Input Status View Event LogView Event Log View Input Status View Output Status View Output Status Section A.5.1 Section A.5.2 Silence Alarm Backup Log Files Alarm Log File Back Up Alarm Log FileBackup Log Files Event Log File Back Up Event Log File Login Setup MenuLogin Menu Setup Menu Setup MenuTips on Using the Service Terminal Interface See Description Setup Inputs Setup Inputs Setup Zones Setup Common AlarmSetup Common Alarm Setup Zones Setup Outputs Setup Outputs Change Password Setup System InfoSetup System Info Set Date & Time Setup Site ID Backup & Upload Configuration File Backup Factory Defaults Backup & Upload Configuration File Upload Firmware Update Firmware Update Service Terminal Interface only Auto Sequencing Setup OperationSetup Operation Auto Sequencing Setup Operation Standby Testing Standby Testing Setup Operation Failed Standby Hold DelaySetup Operation Hold Delay Failed Standby Setup Operation Restart Delay Restart DelayOverride Output Override Output Clear Alarms & Logs Clear the Alarm Log Clear Alarms & LogsClear Alarms & Logs Clear Active Alarms Clear Alarms & Logs Clear the Event Log Specifications Liebert AC4 Specifications Specifications Liebert AC4 Page Is t Ne tTwor k Care