Setup Common Alarm, Setup Zones | Emerson AC4 specification

Setup Menu

A.6.2 Setup Common Alarm

For details on this feature, see 7.4 - Setup System - Setup Common Alarm.

Setup Common Alarm

SETUP COMMON ALARM
Select if the common
alarm relay	contact
is to reset	with
silence alarm		CURRENT
		SETTING
		N
1=SETUP COMMON ALARM
2=RETURN TO	SETUP MENU
3=RETURN TO	MAIN MENU

SELECT A NUMBER:1

>RESET COMMON ALARM WITH SILENCE-YES(Y) OR NO(N)? >[N]

>[

>COMMAND SUCCESSFUL

A.6.3 Setup Zones

For details on this feature, see 7.5 - Setup System - Setup Zones.

Setup Zones

SETUP ZONES

Select zones		and number
of devices		in the zone
ZONE	#	DEVICES
1=ZONE 1		2
2=ZONE 2		2
3=RETURN TO		SETUP MENU
4=RETURN TO		MAIN MENU

SELECT A NUMBER:1

># DEVICES IN ZONE 1 >[2] >[

>COMMAND SUCCESSFUL

Liebert® AC4™

66

Image 72

Emerson AC4 user manual Setup Common Alarm, Setup Zones

Contents

Liebert AC4 Page Table of Contents Setup System Setup Common Alarm 7.5 Setup System Setup Zones Appendix a Service Terminal Interface Setup Menu Figures Methods of Viewing and Configuring the Liebert AC4 Available AlarmsData Logs Introduction LCD for configuration Outside Enclosure OverviewOperation Typical Configuration Device Liebert ChallengerDevice RS232 LiebertLiebert HimodHimod Controller Board Overview Controller board components Connector DIP switchLCD connector 24VAC power LED Indicators LED indicators summaryOutput LEDs Status LEDs Input LEDs Typical Sequence Installation Considerations InstallationPacking Contents Unpacking and Preliminary Inspection Surface-Mounting the Liebert AC4 Required toolsMounting the Panel Flush-Mounting the Liebert AC4 Connect Power to the Liebert AC4 Electrical connections to panel Wiring Specifications Wiring and ConnectionsWiring specifications Connecting Digital Inputs and Outputs Connecting Liebert Precision Cooling UnitsConnecting Digital Inputs Numbering keys Connecting Digital Outputs Setting the Digital Output JumpersDigital output jumper settings Connecting Common Alarm Outputs RS232 ConnectorCommon alarm outputs Serial interface connector RS232/EIA5 Overview of Menus Guide to Liebert AC4 functions Opening Screen Overview Main Menu OverviewLCD Menu Overview View Status Options View Active Alarms Active AlarmsClearing Active Alarms Active Alarms View Alarm Log Alarm LogAlarm log conditions Alarm Log View Event Log Event LogEvent log conditions Event Log View Input Status Input StatusViewing Additional Input Data Digital input states View Output Status Output StatusViewing Additional Output Data Digital output states Silence Alarm & Backup LOG Files Service Terminal Interface Silence Alarm Service Terminal Interface only Back Up Log Files Service Terminal Interface only Silence Alarm & Backup Log Files Service Terminal Interface Login LoginSystem and Control Options Valid characters for data entry Login Screen System & Control menu Clear Alarms&Logs selectedSetup System menu Clear Alarms/Logs menu Setup System Overview Setup System Setup Inputs Define Input as Alarmable or Event Change Label Name of InputDefine Input as Normally Open or Normally Closed Set Up Alarmable Inputs in Latched or Unlatched Mode Set Up Delay TimeDelay Time Latched / Unlatched Setup System Setup Common Alarm Change to Reset Y or Not Reset NReset Common Alarm Setup System Setup Zones Set Up a ZoneMessage if too few devices entered Message if too many devices entered Setup System Setup Outputs Define Output as Normally Open or Normally Closed Define Operating or Standby Mode Enable or Disable an Output Device in Alarm StatusConfigure Output for Loss of Power Fail-Safe Set Mode Setup System Setup System Info Change PasswordChange the Password Reset Password to the Factory Default Aaaa Setup Site ID Setup Site IDSet Date & Time/Automatic Daylight Saving Time Set Date & Time Backup and Upload Configuration File Back Up the Configuration File Upload the Configuration File Factory Defaults Factory DefaultsFirmware Update Service Terminal Interface only Perform Firmware UPDATE-YESY or NON? N Setup Operation Select Setup OperationSetup Operation Menu Default settings operation features Turn Automatic Sequencing On or Off Activate / DeactivateSet Interval & Start Time 1- to 99-Day Interval Set Start Time Hour Interval Turn Standby Testing On or Off Change Standby TestingSpecify Failed Standby Response Failed Standby response Specify Hold Delay Time Hold Delay TimeRestart Delay Time Setup Operation Menu Override Output Clear Alarms & Logs Clear Active AlarmsClear the Alarm Log Clear the Event Log Liebert AC4 Specifications Specifications Specifications Liebert AC4 Appendix a Service Terminal Interface Comparison of Functions LCD and Service Terminal Interface Connecting to the Service Terminal Interface COM1 Port Setup Create a ConnectionSpecify COM Port Connection Properties Setup Ascii SetupSettings tab Ascii Setup button Connect to the Service Terminal Interface Click on the file name for example, AC4.ht Silence Alarm and Backup Log Files Setup Menu OverviewView Status Overview Main Menu For sample screens, see View Active Alarms View Active AlarmsView Status Menus Main Menu View Alarm Log View Alarm Log View Event Log View Input StatusView Event Log View Input Status View Output Status View Output Status Silence Alarm Section A.5.1 Section A.5.2 Back Up Alarm Log File Backup Log Files Alarm Log FileBackup Log Files Event Log File Back Up Event Log File Setup Menu Login MenuLogin Setup Menu Setup MenuTips on Using the Service Terminal Interface See Description Setup Inputs Setup Inputs Setup Common Alarm Setup ZonesSetup Common Alarm Setup Zones Setup Outputs Setup Outputs Setup System Info Setup System InfoChange Password Setup Site ID Set Date & Time Backup & Upload Configuration File Backup Backup & Upload Configuration File Upload Factory Defaults Firmware Update Service Terminal Interface only Firmware Update Setup Operation Setup Operation Auto SequencingAuto Sequencing Standby Testing Setup Operation Standby Testing Hold Delay Setup Operation Failed StandbySetup Operation Hold Delay Failed Standby Restart Delay Setup Operation Restart DelayOverride Output Override Output Clear Alarms & Logs Clear Alarms & Logs Clear Active AlarmsClear Alarms & Logs Clear the Alarm Log Clear Alarms & Logs Clear the Event Log Specifications Liebert AC4 Specifications Specifications Liebert AC4 Page Ne t Is tTwor k Care