Extron electronic 1600 setup guide Contents

Software Commands

Commands are written in the fonts shown here:

^AR Merge Scene,,Op1 scene 1,1 ^B 51 ^W^C [01]R000400300004000080000600[02]35[17][03]

Contents

E X! *X** X2&* X2(* X2* CE}

NOTE: For commands and examples of computer or device

responses mentioned in this guide, the character “0” is used for

the number zero and “O” is the capital letter “o.”

Computer responses and directory paths that do not have variables are written in the font shown here:

Reply from 208.132.180.48: bytes=32 times=2ms TTL=32 C:\Program Files\Extron

Variables are written in slanted form as shown here:

ping xxx.xxx.xxx.xxx —t

SOH R Data STX Command ETB ETX

Selectable items, such as menu names, menu options, buttons, tabs, and field names are written in the font shown here:

From the File menu, select New. Click the OK button.

Specifications Availability

Product specifications are available on the Extron website,

www.extron.com.

Copyright

© 2013 Extron Electronics. All rights reserved

Trademarks

All trademarks mentioned in this guide are the properties of their respective owners.

The following registered trademarks(®), registered service marks(SM), and trademarks(TM) are the property of RGB Systems, Inc. or Extron Electronics:

Registered Trademarks (®)

AVTrac, Cable Cubby, CrossPoint, eBUS, EDID Manager, EDID Minder, Extron, Flat Field,GlobalViewer, Hideaway, Inline, IP Intercom, IP Link, Key Minder, LockIt, MediaLink, PlenumVault, PoleVault, PURE3, Quantum, SoundField, SpeedSwitch, System Integrator, TeamWork, TouchLink, V-Lock, VersaTools, VN-Matrix, VoiceLift, WallVault, WindoWall, XTP,

XTP Systems

Registered Service Mark(SM) : S3 Service Support Solutions

Trademarks (™)

AAP, AFL (Accu-Rate Frame Lock), ADSP (Advanced Digital Sync Processing), AIS (Advanced Instruction Set), Auto-Image, CDRS (Class D Ripple Suppression), DDSP (Digital Display Sync Processing), DMI (Dynamic Motion Interpolation), Driver Configurator, DSP Configurator, DSVP (Digital Sync Validation Processing), FastBite, FOXBOX, IP Intercom HelpDesk, MAAP, MicroDigital, PowerCage, ProDSP, QS-FPC (QuickSwitch Front Panel Controller), Scope-Trigger, SIS, Simple Instruction Set, Skew-Free, SpeedMount, SpeedNav, TeamWork, Triple-Action Switching, XTRA, ZipCaddy, ZipClip

Introduction	1
About this Guide	1
About the XTP CrossPoint
Matrix Switchers	1
Endpoint Configuration	3
Swapping Boards and
Endpoints	3
Installation	5
Rear Panel	5
I/O Board Configuration
Overview	5
Inputs and Outputs	6
Remote Control	11
Reset	11
Power	11
Additional Connector
Information	12
Front Panel	16
Front Panel Operations	17
Creating a Tie	17
Saving or Recalling a Preset	18
Setting the Front Panel Locks
(Executive Modes)	18
Selecting Lock Mode 2 or
Toggling Between Mode 2
and Mode 0	19
Selecting Lock Mode 2 or
Toggling Between Mode 2
and Mode 1	19
Viewing and Adjusting the Audio
Level	20
Viewing Ties (and
Muting Outputs)	20

Remote Control	21
Selected SIS Commands	21
Establishing a Network
(Ethernet) Connection	21
Number of connections	22
Establishing a USB Port
Connection	22
Host-to-Switcher
Instructions	22
Common SIS Command
Symbols	22
Arrangement of Command and
Response Tables	23
SIS Command and Response
Table for Matrix Switcher
Commands	24
SIS Command and Response
Table for XTP T HDMI	33
SIS Command and Response
Table for XTP R HDMI and
XTP SR HDMI	35
SIS Command and Response
Table for XTP T USW 103	38
SIS Command and Response
Table for IP-Specific
Commands	41
XTP System Configuration
Program	42
Accessing the HTML Pages	42
Configuration	45
Removing and Installing a Board or
Blank Panel	45

XTP CrossPoint 1600 and 3200 • Contents v