Extron electronic DMP 64 manual EDX6%*X6^GRPM GrpmX6%*X6

Command and Response Table for DSP SIS Commands (continued)

Command	ASCII command	Response	Additional description
	(host to device)	(device to host)

Audio group master commands

NOTE: • See Group Masters on page 69, for more information about audio group masters.

•A group must have assigned members for these commands to have an effect.

•For X6^, a positive (+) value is assumed unless a negative (–) value is specified.

•If entering a X6^ value outside the valid range for the group or outside the soft limits, the DMP 64 responds with an “invalid parameter” (E13) error.

•X6^, X6&, and X6* values can be sent without leading zeroes; responses are always 5 digits.

Set a group fader control

Example:

Raise a group fader control

Example

Lower a group fader control

View the group fader control level

Mute a group mute control

Clear (unmute) a group mute control

View a group mute control

Set soft limits

Example:

View soft limits

View group type

EDX6%*X6^GRPM} GrpmX6%*X6^]

Ed2*-293*GRPM}GrpmD02*-00293]

EDX6%*X6&+GRPM} GrpmX6%*X6^]

Ed2*30+GRPM} GrpmD02*-00263]

EDX6%*X6&-GRPM} GrpmX6%*X6^]

EDX6%GRPM} GrpmX6%*X6^]

EDX6%*1GRPM} GrpmDX6%*+00001]

EDX6%*0GRPM} GrpmDX6%*+00000]

EDX6%GRPM} GrpmDX6%*X6$]

ELX6%*X6*upper*X6*lowerGRPM} GrpmLX6%*X6**X6*]

EL2*+60*-60GRPM}GrpmL02*+00060*-00060]

ELX6%GRPM} GrpmLX6%*X6**X6*]

EPX6%GRPM} GrpmPX6%*X6(]

Set the group fader to a value of X6^.

Set the group 2 fader control to -29.3 dB.

Increase the level of the X6% group fader by X6& dB. Raise the group 2 fader 3 dB (from -29.3 dB to -26.3 dB, starting from the level set

in the “Set a group fader control” example, above.

Decrease the level of the X6% group fader by X6& dB.

In verbose modes 1 and 2, the response is simplified to

X6^].

Mute all blocks in group X6%. Umute all blocks in group

X6%.

For group masters, X6$ is always expressed as a positive or negative 5-digit value.

Set the groups soft limits to

X6* and X6*.

Set the upper soft limit for the group 2 fader to +6.0 dB and the lower limit to -6.0 dB.

In verbose modes 0 and 1, the response is simplified to

X6**X6*].

Show the group type (X6() for group X6%. In verbose

modes 0 and 1, the response is simplified to X6(].

View group members	EOX6%GRPM}	GrpmOX6%*X6)1*X6)2*
		...*X6)16]

X6) is the control or mix point. In verbose modes 0 and 1, the response is simplified to

X6)1*X6)2*...*X6)16].

NOTES: X6) = Audio level control, or mix-point select

X6% = Group master group number X6^ = Group fader level

See Table 1 on page 111 and 112.

01 - 32

dB value, in 0.1 dB increments, using negative numbers but not decimal places. –100.0dB to +80.0 dB is represented by –1000to 800. The valid

range depends on the type of gain or trim block assigned to the group number (X6%).

X6& = Group fader increase/decrease X6* = Group fader soft limit

X6( = Group type

dB value, in 0.1 dB increments, to raise or lower a group fader.

dB value, in 0.1 dB increments. The valid range must be within the range for the gain block grouped in X6%.

6 = gain

12 = mute

DMP 64 • SIS Programming and Control 106