Memory, System reset to factory defaults | Extron electronic MAV 44

Operation, cont’d

Resetting the system to factory defaults (audio/video switchers)

To reset an audio/video switcher to the factory default settings, press and hold the I/O button on the front panel while applying AC power (figure 3-43). Continue to hold the I/O button until all LEDs light and then release the I/O button. The power up sequence completes (all LEDs turn off then turn on and off from left to right, the Video and Audio LEDs turn on, and all other LEDs remain off). System reset:

•Clears all ties and presets

•Clears all video and audio mutes

•Sets the IR receiver to its default condition (disabled)

•Sets all input audio gain levels to their default values

-12 dB for captive screw audio connector (A) models

0 dB for RCA audio connector (A RCA) models

Press and hold the I/O button while you apply power to the switcher.

I/O

VID

AUD

The switcher lights all of the LEDs.

11

Power

	PRESET	I/O
	PRESET
	VID	+dB
I / O	AUD	-dB
		AUDIO SETUP

Release the I/O button.

I/O

VID

The switcher continues the power up process. AUD

Figure 3-43 — System reset to factory defaults

Memory

The current configuration, all presets, and all input audio levels are saved in non- volatile memory within 5 seconds of a change or exiting Audio Setup mode. When power is applied, the last current configuration is retrieved. The previous presets remain intact.

Wait at least 5 seconds after changing any configuration, saving a preset, or exiting Audio Setup mode. Before 5 seconds have elapsed, changes that you have made may not have been saved.

3-26 MAV 44 / 48 / 84 / 88 Matrix Switchers • Operation

Image 50

Extron electronic MAV 44, MAV 88, MAV 84, MAV 48 manual Memory, System reset to factory defaults

Contents

Matrix Switchers MAV 44 / 48 / 84 / 88 Series Sicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad Español FCC Class a Notice Page Stereo audio devices to the output MAV 44 / 48 / 84 / 88 Matrix Switchers Quick Start QS-1Unbalanced stereo audio inputs to Powering on Quick Start MAV Series AV Matrix Switchers, cont’dSaving or recalling a preset QS-2 MAV 44 / 48 / 84 / 88 Matrix Switchers Quick Start Table of Contents Table of Contents, cont’d MAV 44 / 48 / 84 / 88 Matrix Switchers Table of Contents Iii Iv MAV 44 / 48 / 84 / 88 Matrix Switchers Table of Contents One Introductiontroduction, cont’d About the SwitchersMAV 44 / 48 / 84 / 88 Matrix Switchers Introduction Features Video features Introduction, cont’d Audio featuresCommon features Any input to any or all outputs MAV 44 / 48 / 84 / 88 Matrix Switchers Introduction Introduction, cont’d Two Rack mounting the switcher Installationstallation, cont’dMounting the Switcher Tabletop use Furniture mounting the switcher Mounting the switcher Video input and output connections Installation, cont’dCabling and Rear Panel Views Captive screw connector wiring for audio inputs Audio input and output connections audio/video models Captive screw connector wiring for audio output Remote connection Shows a basic external sync configuration External sync connection Power connection Multiple device external sync connection example Three Operationeration, cont’d Front Panel Controls and IndicatorsMAV 44 / 48 / 84 / 88 Matrix Switchers Operation Definitions Power/audio/data LED and infrared sensorPower/data/audio LED Control buttons and LEDs Input and output selection controls and indicatorsOperation, cont’d Audio Setup button Video/+dB LED and Audio/-dB LED Powering up the switcher Operations Creating a set of ties Example 1 Create a set of video and audio ties Press and release the Input 5 button figure Example 2 Add a video tie to a set of video and audio ties This example assumes that you have performed example 11 Select the output Example 3 Remove a tie from a set of ties Press and release the Output 4 button figure Viewing the configuration Video Example 4 View ties by selecting an input 19 Select video and audio Press and release the I/O button figure Example 5 View ties by selecting outputs 24 Select an output Using presets 26 Deselect video to view audio ties only Example 6 Save a preset Preset 2 Preset Example 7 Recall a preset 29 Select Recall Preset mode, MAV Adjusting input audio gain and attenuation Consumer VCR Audio Inputs To exit Audio Setup mode. The Audio Setup LED turns off Example 8 Adjust the input audio gain Seconds 34 Adjust the input audio level +2 dB Resetting audio gain single input Press and release the and buttons simultaneously figure Resetting audio gain all inputs Setting the output audio level Front panel security lockout Executive mode Clearing all ties and presets 43 System reset to factory defaults Memory Optimizing the Audio Audio/Video Switchers Troubleshooting Worksheets Worksheet example 1 System equipment Worksheet example 2 Daily configuration 45 Worksheet example 2 Daily configuration Worksheet example 3 Test configuration 46 Worksheet example 3 Test configuration Configuration worksheet Output destinations Operation, cont’d Four RemoteOperation,cont’d Host-to-Switcher instructionsMAV 44 / 48 / 84 / 88 Matrix Switchers Remote Operation Simple Instruction Set Control Switcher-initiated messages Symbol definitions Switcher error responsesUsing the command/response table Remote Operation, cont’d Command/response table for SIS commands Command Ascii Command Response Additional description Command/response table for SIS commands cont’d IR receiver enable Resets Firmware upload Loading firmware using an SIS command Turn on the echo function Select the firmware upgrade file Matrix Switchers Control Program Installing the software Using the software Overview Extron Matrix Switchers Control Program window blank Updating the firmware 11 Determining the firmware version 12 Open window, version 2.xx firmware files 13 Open window, version 1.xx firmware files Windows buttons, drop boxes, and the trash can Tools menu Windows menusFile menu Audio-input Configuration selection Preferences menu Master-Reset selection 18 Ties shown as crosspoints Using Emulation mode Using the help system AAppendix a SpecificationsandandPartPartNumbers,Numberscont’d Specifications Sync composite video and S-video models Specifications and Part Numbers, cont’d Audio output audio models Control/remote switcher Part Numbers MAV Series AV switchersReplacement parts Included parts Optional accessories Cables Video Cable Assorted connectors BNC connectorsPre-cut cables Composite video Cable Extron’s Warranty Asia Japan Extron Electronics, Europe Beeldschermweg 6C