Manuals / Extron electronic / Computer Equipment / Switch

Extron electronic MAV Plus Series Front panel Configuration port, Optional 9-pin TRS RS-232 cable

Models: MAV Plus Series

1 186

Download 186 pages 11.96 Kb

Page 91

Front panel Configuration port

The front panel Configuration port is hard configured as RS-232 only. The port can operate at the 9600, 19200, 38400, or 115200 baud rate, but Extron recommends leaving this port at 9600 baud only.

NThis port is independent of the rear panel Remote port and is not affected by changes to the rear panel port’s protocol. This front panel port’s protocol can be changed via an SIS command only. See the "Command/Response table for IP-Specific SIS commands", on page 4-23, to configure both ports using an SIS command.

The optional 9-pin D to 2.5 mm mini jack TRS RS-232 cable, part #70-335-01can be used for connection to the Configuration port.

		6 feet
		(1.8 m)
1	6	Part #70-335-01
1

5	9
5			Tip
			Tip
			Ring
9-pin D	Connection	TRS Plug	Sleeve (Gnd)
9-pin D	Connection	TRS Plug
Pin 2	Computer's Rx line	Tip
Pin 3	Computer's Tx line	Ring
Pin 5 Computer's signal ground		Sleeve

Figure 4-2 — Optional 9-pin TRS RS-232 cable

CrossPoint 450 Plus and MAV Plus Switchers • Programmer’s Guide

4-3

Image 91

Extron electronic MAV Plus Series manual Front panel Configuration port, Optional 9-pin TRS RS-232 cable

Contents

CrossPoint 450 Plus Series MAV Plus series Large Scale Matrix SwitchersInstrucciones de seguridad Español Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen DeutschFCC Class a Notice Page Table of Contents Table of Contents, cont’d Command/Response Table for IP-Specific SIS Commands Table of Contents, cont’d CrossPoint 450 Plus and MAV Plus Switchers Table of Contents Table of Contents, cont’d One CrossPoint 450 Plus and MAV Plus Switchers Introduction About the Matrix SwitchersAbout this Manual CrossPoint 450 Plus / MAV Plus application Introduction, cont’d Audio inputs audio BMEs only FeaturesDsvp data display Tie any input to any or all outputs Introduction, cont’d Two Mounting the Switcher Setup and Installation ChecklistMounting instructions Rear Panel Cabling and FeaturesVideo or sync input and output video and sync BMEs\⤀ Installation, cont’dAudio input and output systems with audio BMEs\⤀ Sync termination switches systems with sync BMEs\⤀Typical audio connectors BME connection and selection Setting a BME address video BME shownDaisy-chaining BMEs video BME shown Remote RS-232/RS-422Ethernet Cabling and RJ-45 connector wiringExternal sync systems with MAV Plus video BMEs\⤀ Reset buttonBBG 6 a PowerPin D Front Panel Configuration PortInstallation, cont’d Three Operation CrossPoint 450 Plus and MAV Plus Switchers OperationC d e f g h Front Panel Controls and IndicatorsInput and output buttons Operation, cont’dSystems with CrossPoint 450 Plus Wideband switcher BMEs Control buttons CrossPoint 450 Plus and MAV Plus Switchers Operation Operation, cont’d Rgbhv Video Primary and Redundant Power Supply LEDs Power indicatorsButton labels QS-FPC Front Panel OperationsDefinitions PowerCreating a configuration Select an input Press and release the input 5 button Example 1 Creating a set of tiesInput 5 video and audio tied To outputs 3, 4, Output Press and release the Input 5 button Example 2 Adding a tie to a set of tiesCrossPoint 450 Plus and MAV Plus Switchers Operation Select the output Press and release the output 4 button Example 3 Removing a tie from a set of tiesConfirm the change Press and release the Enter button Viewing a configuration 49 50 51 52 53 54 55 17 18 19 20 21 22 23 24 25 GroupingPress the Preset button to select group Example 5 Grouping inputs and outputs Group # Example 6 Setting the RGB delay for an output Setting RGB delay systems with wideband BMEs\⤀3 4 5 6 7 8 9 17 18 19 20 21 22 23 24 25 26 NI Exit RGB Delay mode Press and release the Rgbhv button Using presetsSeconds Example 7 Saving a preset4 5 6 7 8 17 18 19 20 21 22 23 24 NI Example 8 Recalling a presetExample 9 Muting and unmuting an output Muting and unmuting outputsMute outputs one at a time View button returns to unlit or background illumination Audio gain and attenuation Example 10 Viewing and adjusting an input audio level 4 5 6 7 8 9 17 18 19 20 21 22 23 Lower the volume Reading the displayed volume Audio volume adjustment settings Select an output Press and release the Output 1 button Example 11 Viewing and adjusting an output volume level10 11 12 13 23 24 25 26 27 28 29 39 40 41 42 43 44 45 Selecting Lock mode 2 or toggling between mode 2 and mode Setting the front panel locks Executive modes\⤀Power Performing a system reset from the front panelBackground illumination Serial protocol Selecting the rear panel Remote port protocol and baud rateRear Panel Operations Reset Mode Comparison/SummaryReset times Performing soft system resets reset modes 3, 4, and 5\⤀Optimizing the Audio Systems with Audio BMEs Performing a hard reset reset modeConfiguration Worksheets TroubleshootingGeneral checks Input sources Worksheet example 1 System equipmentWorksheet example 2 Daily configuration Worksheet example 2 Daily configurationWorksheet example 3 Test configuration Worksheet example 3 Test configurationOperation, cont’d Preset # Blank configuration worksheetOperation, cont’d Four Rear panel Remote port Serial PortsOptional 9-pin TRS RS-232 cable Front panel Configuration portEthernet LAN\⤀ Port Default IP addressesEthernet connection Number of connections Connection TimeoutsUsing Verbose Mode Establishing a connectionSwitcher-Initiated Messages Host-to-Switcher InstructionsUsing the Command/Response Tables Switcher Error ResponsesX2! = Command/response table for SIS commandsSymbol definitions X1 =Description Command Ascii command Response Additional+QX!*X@!...X!*X@! Qik @ %$-G $*X%G$*X&g $+G@-V @+VAudio mute commands EX1,X@1,X@2, ... X@nMR X1@X1# 1 , X1# 2 , ... X1# n $ GEX *X@ *1VC View ties, gain, volume, mutes, and presets \⤀ 0 0 0 4 1 1 2 2 1 2 2 3 3 3 3 2 1 2 2 3 3 3 EX1& 1X1& 2 ...X1& n OEX1*X1@,X1!NP NmpX1*X1@,X1 EX1,X1!NR NmrX1,X1EX1,X1@NP EX1 *X1@ ZP EX1 ZRInformation requests \ ⤀ X2 -X2EDF Command/Response Table for IP-Specific SIS Commands X3% IptX3@X3# IpzX3$Special Characters Programmer’s Guide, cont’d Five Installing the software Matrix Switchers Control ProgramCrossPoint 450 Plus and MAV Plus Switchers Matrix Software Software operation via Ethernet Ethernet protocol settingsMatrix Software, cont’d Using the Matrix Switcher Control softwareAddress and password entry Extron Matrix Switchers Control Program window Sample program window, with ties and icons Control program IP Setting/Options window IP Settings/Options windowHardware Address field Address and Name fieldsUse Dhcp check box Date, Time local\⤀, and GMT offset\⤀ fields Sync Time to PC button Administrator Password and User Password fieldsUse Daylight Saving check box Mail Addressee fields Miles StandishUpdating firmware Location of firmware upgrade filesDownloading firmware upgrade files Ethernet-connected firmware upload 10. See Ethernet-connected firmware upload, below11 Add Device window Serial-port-connected firmware upload13 Choose Firmware File window 15 Html Files List window Uploading Html filesWindows menus Windows buttons, drop boxes, and trash canFile menu Tools menu 16 Status window 17 Ties shown as crosspoints Preferences menuMaster-Reset selection Using the help system Using Emulation modeButton Label Generator Program Installing the Button Label Generator software20 Button Label Generator window Using the Button Label Generator softwareSix Downloading the Startup CrossPoint 450 Plus and MAV Plus Switchers Html OperationSystem Status Status TabDsvp page systems with a sync BME only\⤀ Html Operation, cont’dSystem Settings Configuration TabIP Address field IP Settings fieldsUnit Name field Dhcp radio buttonsDate/Time Settings fields Date/Time Settings fieldsPasswords PasswordsMail IP Address field Email SettingsDomain Name field Email address fields Firmware UpgradeClick the Browse button. a Choose File window appears File Management File Management TabSet and View Ties Control TabCreating or deleting a tie 12 RGB and Audio Settings Rgbhv and Audio Settings13 Input selection drop box 15 Output selection drop box Mute and unmute one or all outputs17 Output selection drop box 19 Output selection drop box Change the output volume level audio models\⤀Number Output Steps Attenuation Volume Saving a preset Global PresetsSpecial Characters Recalling a presetAppendixAA Ethernet Link Default IP addressPinging to determine the Extron IP address Pinging to determine the Web IP address Ethernet Connection, cont’d Telnet tips Connecting as a Telnet clientOpen Close Escape character and Esc keyLocal echo Set carriage return line feedIP addresses and octets Subnetting a PrimerGateways Local and remote devicesExample Determining whether devices are on the same subnetAppendixBB Reference Information CrossPoint 450 Plus SpecificationsControl/remote switcher Reference Information, cont’d MAV Plus SpecificationsAudio input audio BMEs EMI/EMC CrossPoint 450 Plus system part numbers Part Numbers and AccessoriesModel Part number MAV Plus system part numbers Order all BMEs of the same matrix size, such as BME part numbersCrossPoint 450 Plus sync BMEs CrossPoint 450 Plus wideband video BMEsMAV Plus video BMEs Included parts Replacement partsRG59 high resolution cable Part number Optional accessoriesAccessory Part number Bulk cable RG6 super high resolution cable Part numberMHR mini high resolution cable Part number MHR mini high resolution cable Part numberInstalling labels in the matrix switcher’s buttons Removing and Installing Button LabelsButton label blanks Reference Information, cont’d Extron Warranty Extron USA West