Manuals / Brands / Computer Equipment / Switch / Extron electronic / Computer Equipment / Switch

Extron electronic MAV Plus Series Confirm the change, Input 5 video tied, The current configuration is now:, •Audio — Input 5 audio tied to output 3 and output

1 186

Download 186 pages, 10.39 Mb

5. Confirm the change: Press and release the Enter button.

Press the Enter button to confirm the configuration change.

ENTER All input buttons and output buttons return to unlit or background illumination.

The Enter button returns to unlit or background illumination.

The current configuration is now:

•Video — Input 5 video tied to output 1, output 3, output 4, and output 8•Audio — Input 5 audio tied to output 3 and output 8

Input 5 video tied

to outputs 1, 3, 4, and 8. Input 5 audio tied to outputs 3 and 8.

Input

4 Output

8	Video
	Video
	Audio

CrossPoint 450 Plus and MAV Plus Switchers • Operation 3-19

Contents

Page Precautions FCC Class A Notice Page Table of Contents Table of Contents, cont’d Setting RGB delay .(sy stems with wideband BMEs) Using presets Muting and unmuting outputs Switcher-Initiated Messages Switcher Error Responses Using the Command/Response Tables Command/response table for SIS commands Chapter Six • HTML Operation Downloading the Startup Page Status Tab stem Status page DSVP page (sy Appendix A • Ethernet Connection Ethernet Link Default IP address Connecting as a Telnet client Subnetting — A Primer Page Chapter1One Introduction Introduction with or without always not available Figure 1-1— CrossPoint 450 Plus / MAV Plus application CrossPoint 450 Plus and MAV Plus Switchers • Introduction Introduction, cont’d •Rear panel Local Area Network (LAN) Ethernet port •Rear panel Remote RS-232/RS-422port •Front panel Configuration (RS-232)port The LAN port can be connected through a LAN or wide area network (WAN) Video (video BMEs) — CrossPoint 450 Plus wideband video — MAV Plus low resolution video — Bandwidth — Audio inputs (audio BMEs only) — Windows -based control program on a local-area network (LAN) or Internet (IP) connection (figure Switching flexibility — •Tie any input to any or all outputs Quick multiple tie — Audio follow — Audio breakaway — Labeling — Global memory presets — Rack mounting — Executive I/O grouping — Chapter2Two Installation Installation Mounting instructions Insert the switcher BME into the rack, aligning the holes in the mounting bracket with those in the rack Secure the switcher BME to the rack using the supplied bolts •The Sync Termination DIP switches (c) are found on the sync BME only Installation, cont’d Figure 2-2— MAV Plus 6464 Stereo Audio BME Video or sync input and output (video and sync BMEs\⤀ Connect these planes to BMEs Sync termination switches (systems with sync BMEs\⤀ Sync termination switches — Audio input and output (systems with audio BMEs\⤀ Figure Connections for balanced and unbalanced audio inputs — NThe length of exposed wires is critical. The ideal length is 3/16 inch (5 mm) Figure 2-5— Typical audio connectors Connections for balanced and unbalanced audio outputs — These 3.5 mm (stereo audio BMEs) or The ideal length is 5 mm) BME connection and selection BME address switch — Figure 2-8— Setting a BME address (video BME shown) BME COMM interconnect ports — Figure 2-9— Daisy-chainingBMEs (video BME shown) 2-8CrossPoint 450 Plus and MAV Plus Switchers • Installation RS-232/RS-422 Remote Connect a host device, such as a computer, touch panel control, or RS-232 capable PDA to the switcher via this RS-232/RS-422 control (figure 2-10) Figure 2-10— Remote RS-232/RS-422connector MKP 2000 Remote Control Panel User’s Manual Ethernet Ethernet port — on BME 0 only Ethernet connection indicators — Cabling and RJ-45connector wiring Reset button Reset button — Events (mode 3) reset — IP settings (mode 4) reset — Absolute (mode 5) reset — Figure 2-12— Simple external sync connection example Figure 2-13— Multiple device external sync connection example AC power connector — 2-12CrossPoint 450 Plus and MAV Plus Switchers • Installation Configuration port — #70-335-01 Figure 2-14— Front panel configuration port Figure 2-15— Optional 9-pinTRS RS-232cable This port is RS-232only, with its default protocols as follows: Page Chapter3Three Operation Operation Figure 3-1— CrossPoint 450 Plus 6464 series with integrated QS-FPC aInput buttons — See page bOutput buttons — See page cEnter button — See page dPreset button — See page Operation, cont’d Input and output buttons Primary functions Secondary functions 3-4CrossPoint 450 Plus and MAV Plus Switchers • Operation Input buttons — (Input 1 only) ❏(Systems with CrossPoint 450 Plus Wideband switcher BMEs Input 1 through 10 only) (Systems with audio BMEs) Control buttons Enter button — 3-6CrossPoint 450 Plus and MAV Plus Switchers • Operation Preset button — View ) button — (Systems with CrossPoint 450 Plus Wideband switcher BMEs) Esc 3-8CrossPoint 450 Plus and MAV Plus Switchers • Operation I/O control buttons RGBHV (CrossPoint 450 Plus) button or Video (MAV Plus) button — Audio button — Power indicators Figure 3-2— Front panel without an integrated QS-FPC iPrimary and Redundant Power Supply LEDs — Green — D DocumentCamera Figure 3-3— Sample button labels and icons Definitions Tie — An input-to-outputconnection Set of ties — tied Configuration — One or more ties or one or more sets of ties Creating a configuration Green: Red: potential ties blink Example 1: Creating a set of ties This example assumes that there are no ties in the current configuration Clear all selections : Press and release the Esc button Select video and audio for the tie 5. Confirm the change: Press and release the Enter button Input 5 video and audio tied to outputs 3, 4, and 4 Output Example 2: Adding a tie to a set of ties This example assumes that you have performed Select video only for the tie 4. Select the output: Press and release the output 1 button 3-16CrossPoint 450 Plus and MAV Plus Switchers • Operation The current configuration is now: •Input 5 video tied to output 1, output 3, output 4, and output •Input 5 audio tied to output 3, output 4, and output Input 5 video tied to outputs 1, 3, 4, and 8. Input 5 audio tied Example 3: Removing a tie from a set of ties Select audio only for the tie 3. Select the output: Press and release the output 4 button 3-18CrossPoint 450 Plus and MAV Plus Switchers • Operation •Video — Input 5 video tied to output 1, output 3, output 4, and output •Audio — Input 5 audio tied to output 3 and output to outputs 1, 3, 4, and 8. Input 5 audio tied to outputs 3 and Viewing a configuration not and Green Red Example 4: Viewing video and audio, audio only, and video only ties NThis example assumes that you have performed example 1, example 2, and example 1. Clear all selections: Press and release the Esc button Select Select both video and audio for viewing • The selected output button • The tied input button (input 5) • The output buttons for all of the other outputs that are tied to the input Deselect RGBHV or Video : Press and release the RGBHV Exit I/O grouping from the front panel only Figure 3-4— I/O grouping of incompatible video formats can Suggested applications for the I/O grouping feature include: •Segregating input and output devices that are in separate rooms Create I/O groups on the front panel as follows: To enter I/O Group mode, press and hold the Input 1 and Output 1 buttons until the input and output buttons light to display the ungrouped inputs and Example 5: Grouping inputs and outputs 3. Select an I/O group: Press and release the Enter button to select group Assign inputs and outputs Select a different I/O group I/O Group •Group 1 consists of inputs 1 through 4 and outputs 1 through •Group 2 consists of inputs 5 through 8 and outputs 5 through 3-26CrossPoint 450 Plus and MAV Plus Switchers • Operation Setting RGB delay (systems with wideband BMEs\⤀ Example 6: Setting the RGB delay for an output Enter RGB Delay mode 3. Select an output: Press and release the Output 17 button The RGB delay is protected when front panel Increase the delay You can press and 5. Exit RGB Delay mode: Press and release the RGBHV button Using presets preset current configuration Presets Example 7: Saving a preset Save Preset Select the preset 3-30CrossPoint 450 Plus and MAV Plus Switchers • Operation Example 8: Recalling a preset 2. Select Recall Preset mode: Press and release the Preset button Muting and unmuting outputs One at a time without Example 9: Muting and unmuting an output Enter Select video and audio This example shows the front panel indications if Output mutes are protected when front panel Mute the outputs Unmute the outputs 3-34CrossPoint 450 Plus and MAV Plus Switchers • Operation Viewing and adjusting the input audio level (systems with audio BMEs\⤀ Figure 3-5— Audio gain and attenuation Example 10: Viewing and adjusting an input audio level Enter Audio mode 3. Select an input: Press and release the Input 5 button 3-36CrossPoint 450 Plus and MAV Plus Switchers • Operation Change the input level 5. Exit Audio mode: Press and release the Audio button Viewing and adjusting the output volume (systems with audio BMEs\⤀ 3-38CrossPoint 450 Plus and MAV Plus Switchers • Operation Reading the displayed volume At maximum attenuation At no attenuation Push Esc lit Audio volume adjustment settings = blinking LED 3-40CrossPoint 450 Plus and MAV Plus Switchers • Operation Example 11: Viewing and adjusting an output volume level 3. Select an output: Press and release the Output 1 button Volume is protected when front panel Change the volume 17 8 9 101112 13 14 151623242526272829303132NI 3-42CrossPoint 450 Plus and MAV Plus Switchers • Operation Setting the front panel locks (Executive modes\⤀ View-Only mode 0 — mode 1 — mode 2 — If the switcher is in Performing a system reset from the front panel •Clears all ties and presets •Clears all video and audio mutes •Resets all I/O grouping Background illumination Selecting the rear panel Remote port protocol and baud rate Serial Port Selection and Configuration hold all Change a value: 3-46CrossPoint 450 Plus and MAV Plus Switchers • Operation See the following table for a summary of the modes Reset Mode Comparison/Summary Performing soft system resets (reset modes 3, 4, and 5\⤀ 3-48CrossPoint 450 Plus and MAV Plus Switchers • Operation Performing a hard reset (reset mode 1) unless General checks Plasma display S-videoproblem (CrossPoint 450 Plus wideband BMEs only\⤀ it is not Solution 3-50CrossPoint 450 Plus and MAV Plus Switchers • Operation Worksheet example 1: System equipment Figure 3-6— Worksheet example 1: System equipment Worksheet example 2: Daily configuration In this example: •The image of the presenter, from the main podium camera (input 1), is: Displayed in the main hall (output 1) Displayed in the conference room (output 4) to the overflow crowd Worksheet example 3: Test configuration Figure 3-8— Worksheet example 3: Test configuration Page 55-3Operation • Switchers Plus MAV and Plus 450 CrossPoint Input sources Output Preset # Title: Page Chapter4Four Programmer’s Guide Programmer’s Guide Front panel Configuration port but Extron recommends leaving this port at 9600 baud only Figure 4-2— Optional 9-pinTRS RS-232cable CrossPoint 450 Plus and MAV Plus Switchers • Programmer’s Guide Programmer’s Guide, cont’d Patch (straight-through) cable — Figure 4-3— RJ-45Ethernet connector pin assignments Establishing a connection 1. Open a TCP socket to port 23 using the switcher’s IP address If the switcher is password Login User 4-6CrossPoint 450 Plus and MAV Plus Switchers • Programmer’s Guide Page Command/response table for SIS commands Symbol definitions X1# X1$ X1& E+QX!*X@!...X!*X@!} Qik] Command/response table for SIS commands (continued\⤀ Video mute commands Audio input gain and attenuation 4-10CrossPoint 450 Plus and MAV Plus Switchers • Programmer’s Guide Audio output volume value X@*X*V Audio mute commands Save, recall, and directly write global and room presets 4-12CrossPoint 450 Plus and MAV Plus Switchers • Programmer’s Guide EX1) EVM} EX(*X@*1VC} EX View ties, gain, volume, mutes, and presets (continued\⤀ X$LS EX@*X1^D} EX@D} EX1&1X1&2...X1&nI} EX1&1X1&2...X1&nO} EI} EO} EX(NG} EX1),X1!NR} NmrX1),X1!] EZZ} EZA} EZV} EZG} EX(ZG} CrossPoint 450 Plus and MAV Plus Switchers • Programmer’s Guide Information requests (continued\⤀ EDF} Command/Response Table for IP-SpecificSIS Commands X3@ X4@ X4% X3)] EX3)CN} ECN} EX3@CT} IptX3@] ECT} EX4!,X4#,X4$,X4$, ... ,X4$EM} IpeX4$,X4$,X4$, ... ,X4$] EX4!EM} EX4^DH} IdhX4^] Page Chapter5Five Matrix Software Matrix Software Install Figure 5-2— Software installation Remote RS-232/RS-422 port — Matrix Software, cont’d Using the Matrix Switcher Control software Start Figure 5-3— Comm port selection window IP [LAN] in step Figure 5-4— Address and password entry If the IP address is correct, proceed to step 3b , proceed to step If the address is not correct Follow Figure 5-5— Extron Matrix Switchers Control Program window 5-6CrossPoint 450 Plus and MAV Plus Switchers • Matrix Software Print Tie Map Figure 5-6— Sample program window, with ties and icons IP Settings/Options window The IP Settings/Options window (figure 5-7),accessible by clicking Tools IP options Figure 5-7— Control program IP Setting/Options window 5-8CrossPoint 450 Plus and MAV Plus Switchers • Matrix Software Address and Name fields Matrix IP Address Gateway IP Address Subnet Mask NThe above fields are unavailable for editing when DHCP is selected Date, Time (local\⤀, and GMT (offset\⤀ fields GMT Sync Time to PC Date Time (local) Sync Time to PC button Use Daylight Saving check box Use Daylight Saving For Daylight Saving Time in Europe and Brazil, refer to the Administrator Password and User Password fields E-mailAddressee fields None Send test E-mail 5-12CrossPoint 450 Plus and MAV Plus Switchers • Matrix Software Updating firmware Download Firmware Figure 5-8— Location of firmware upgrade files Run Page Update If you are connected via the LAN port, the Select Files window appears Ethernet-connectedfirmware upload Figure 5-10— Select files window Open Serial-port-connectedfirmware upload Cancel Figure 5-11— Add Device window Figure 5-12— Extron Firmware Loader window 5-16CrossPoint 450 Plus and MAV Plus Switchers • Matrix Software Figure 5-13— Choose Firmware File window 15. In the Firmware Loader window, click Begin Figure 5-14— Firmware Loader screen 16. Click Exit to close the Firmware Loader Uploading HTML files Figure 5-15 — HTML Files List window Upload HTML pages as follows: The files listed in figure Connect the PC to the matrix switcher via the switcher’s Windows buttons, drop boxes, and trash can Power Executive Mode Rooms menu — Room Tools menu Assign Device Icons Edit Device Palette RGB delay settings Audio-Output Hardware status Figure 5-16— Status window Name presets Show Strings Preferences menu Immediate Changes Hold/Verify Changes Ties as Lines Ties as Crosspoints Icons in I/O Boxes Numbers in I/O Boxes Catch FPC/others changes Master-Resetselection Using Emulation mode 6464 Series 1 or Figure 5-18— Emulation mode configuration Using the help system Installing the Button Label Generator software Figure 5-19— Location of software on the web site Using the Button Label Generator software Programs Extron Electronics Button Label Generator Figure 5-20— Button Label Generator window Chapter6Six HTML Operation HTML Operation If so System Status page Status Figure 6-2 — System Status page CrossPoint 450 Plus and MAV Plus Switchers • HTML Operation HTML Operation, cont’d DSVP page (systems with a sync BME only\⤀ DSVP Figure 6-3 — DSVP page 6-4CrossPoint 450 Plus and MAV Plus Switchers • HTML Operation System Settings Page Configuration Figure 6-4 — System Settings page is not IP Settings fields Submit Unit Name field DHCP radio buttons DHCP On Date/Time Settings fields Figure 6-5 — Date/Time Settings fields Local Date/Time Zone Passwords page Passwords Figure 6-6 — Passwords page 6-8CrossPoint 450 Plus and MAV Plus Switchers • HTML Operation Email Settings page Edit Save Edit/Save Figure 6-7 — Email Settings page Email address fields E-Mail Options Suspend Firmware Upgrade page Figure 6-9— Firmware upgrade Browse Upload File Management Page File Management Figure 6-10 — File Management page Upload File 6-12CrossPoint 450 Plus and MAV Plus Switchers • HTML Operation Set and View Ties page Control Figure 6-11— User Control Ties page •The amber buttons indicate video and audio ties buttons indicate Creating or deleting a tie Video Only Audio Only Video & Audio 6-14CrossPoint 450 Plus and MAV Plus Switchers • HTML Operation RGBHV and Audio Settings page The RGB and Audio Settings page provides the means to: Systems with MAV Plus audio BMEs only — Systems with CrossPoint 450 Plus sync BMEs only — Set the RGB delay (switching interval) Change the input gain and attenuation (systems with audio BMEs\⤀ Figure 6-13— Input selection drop box Figure 6-14— Gain drop box 6-16CrossPoint 450 Plus and MAV Plus Switchers • HTML Operation Mute and unmute one or all outputs Figure 6-15— Output selection drop box Mute UnMute Mute All Change the RGB delay (systems with CrossPoint 450 Plus sync BMEs\⤀ Figure 6-17— Output selection drop box Figure 6-18— RGB delay drop box 6-18CrossPoint 450 Plus and MAV Plus Switchers • HTML Operation Change the output volume level (audio models\⤀ Figure 6-19— Output selection drop box Figure 6-20— Volume Steps drop box of steps 6-20CrossPoint 450 Plus and MAV Plus Switchers • HTML Operation Global Presets page Global Presets Figure 6-21 — Global Presets page Saving a preset Save the current configuration (configuration 0) as a preset as follows: Recalling a preset 6-22CrossPoint 450 Plus and MAV Plus Switchers • HTML Operation AppendixAA Ethernet Connection Ethernet Connection Pinging Pinging to determine the Web IP address Pinging mail Configuring the matrix switcher BME for network use via the ARP command CrossPoint 450 Plus and MAV Plus Switchers • Ethernet Connection Ethernet Connection, cont’d A-4CrossPoint 450 Plus and MAV Plus Switchers • Ethernet Connection Connecting as a Telnet client Telnet tips Open If the BME is not password protected If the BME is password protected Escape character and Esc key Escape character is ‘Ctrl+]’ Local echo 1*1!In1 Out1 All 1*1 sub net Gateways Local and remote devices IP addresses and octets Determining whether devices are on the same subnet compared not compared Unmasked octets are compared Masked octets are not compared AppendixBB Reference Information Reference Information Control/remote — switcher Baud rate and protocol 9-pinD connector�� RS‑232: 2 = Tx, 3 = Rx, 5 = GND RS‑422: 2 = Tx-,3 = Rx-,5 = GND, 7 = Rx+, 8 = Tx+ Microsoft® Internet Explorer, Telnet Reference Information, cont’d Video — video BMEs 對�� 150 MHz (-3dB), fully loaded Video input — video BMEs Number/signal type�� 32, 48, or 64 composite video Audio input — audio BMEs 32, 48, or 64 stereo balanced/unbalanced or 32, 48, or 64 mono balanced/unbalanced (32, 48, or 64) 3.5 mm captive screw connectors, 5 pole (32, 48, or 64) 3.5 mm captive screw connectors, 3 pole Enclosure type �� Metal Enclosure dimensions 32 x 48 through 64 x 64 Series video BMEs 18.0 lbs (8.2 kg) 32 x 48 through 64 x 64 Series stereo audio BMEs 19.0 lbs (8.6 kg) 32 x 48 through 64 x 64 Series mono audio BMEs 18.5 lbs (8.4 kg) CrossPoint 450 Plus system part numbers A front panel controller is incorporated into one of the BMEs in the system Model Part number B-7 MAV Plus system part numbers A front panel controller is incorporated into the video BME B-8CrossPoint 450 Plus and MAV Plus Switchers • Reference Information BME part numbers NThe complete system part numbers listed on the preceding pages are for either: •RGBHV systems (three wideband video and two sync BMEs) •Composite video switchers (one video BME) For custom systems CrossPoint 450 Plus wideband video BMEs CrossPoint 450 Plus sync BMEs MAV Plus video BMEs B-10CrossPoint 450 Plus and MAV Plus Switchers • Reference Information MAV Plus stereo audio BMEs MAV Plus mono audio BMEs Included parts Part Replacement parts Optional accessories These items can be ordered separately: Accessory Cables Bulk cable MHR mini high resolution cable Terminated cable assemblies '/7.6 m '/10.6 m '/15.2 m Installing labels in the matrix switcher’s buttons Figure B-1— Illuminated button label replacement B-14CrossPoint 450 Plus and MAV Plus Switchers • Reference Information Page Page USA, Canada, South America and Central America: Japan: Europe, Africa, and the Middle East: China: