Extron electronic MAV Plus Series manual EX1& 1X1& 2 ...X1& n O

MAV Plus 3264

See below.

Example:

E40133000044...4I}

EX1&1X1&2...X1&nI}

GriX1&1X1&2X1&3...X1&n]

Each X1& entry is the group number assigned to an input position, starting from input 1. n is the highest- numbered input for this model.

N The group that is assigned in each of the following I/O grouping commands (X1&) must be 1, 2, 3, 4, or 0 (not grouped). Write input grouping

I/O Grouping

Output 14 interval is

2.5 seconds (5 x 0.5 sec.).

View RGB delay Example:

X1^]

05]

EX@D}

E14D}

Set the RGB interval for ties to output 13 to 3.5 seconds (7 x 0.5 sec.).

Out13•Dly07]

Set RGB delay Example:

OutX@•DlyX1^*1]

EX@*X1^D}

E13*7D}

RGB delay (CrossPoint)

View connections

X1%1X1%2X1%3...X1%n]

Each X1%response is the connection status (0 = no input detected, 1 = input detected) of

an input, starting from input 1. n is the maximum number of inputs for this model.

2LS

031.5,060.00]

View DSVP

(individual sync frequency) Example:

Listed as horizontal frequency, vertical frequency. Input 2 frequency is

31.5 kHz (horizontal) and

60 Hz (vertical).

N The matrix switcher returns 000.00,000.00 if there is no connection or if sync frequencies are not applicable. 0LS

X1$,X1$]

X$LS

Digital Sync Validation Processing (DSVP)

(switcher to host)

(host to switcher)

Response

ASCII command

Command

Additional description

Programmer’s Guide, cont’d

Command/response table for SIS commands (continued)

Input 1 in group 4						Input 2 not grouped																						Input 32 in group 3
Response #s = group: Gri	4 0 1 3				3 0 0 0 0 4 4								4 4 1 1 2 2 1 2 2 3 3 3 3 2 1 2 2 3 3 3 3
Input:	01	02	03	04		05	06	07	08	09	10	11		12	13	14	15	16	17	18	19	20	21	22	23	24	25	26	27	28	29	30	31	32

Input 1 - Group 4, Input 2 -

Group 0 (not grouped), ...

Input 32 - Group 4.

NIf verbose mode is off (see the "Set verbose mode" SIS command on page 4-23), the Gri preface is omitted in the response.

Write output grouping	EX1&1X1&2...X1&nO}	GroX1&1X1&2X1&3...X1&n] Each X1& entry is the group
		number assigned to an output
		position,startingfromoutput1.
		n is the highest-numbered
		output for this model.

NIf verbose mode is off (see the "Set verbose mode" SIS command on page 4-23), the Gro preface is omitted in the response.

N X@ = Output number	01	– (maximum number of outputs for your model)
X$ = Input number	01	– (maximum number of inputs for your model)
X1$ = Sync frequency	xxx.xx (frequency in Hz [V] or kHz [H])
X1% = Signal detection	0 = no input detected		1 = input detected
X1^ = RGB delay interval	Delay in ½ second increments (10 maximum)
X1& = Group # (for I/O grouping)	1 – 4 (0 = no group)

4-16 CrossPoint 450 Plus and MAV Plus Switchers • Programmer’s Guide