Preliminary | Extron electronic MVX VGA A specification

Male-to-male VGA molded connector cables	Part number

VGA M3' MHR, 3' (0.9 m)	26-238-24

VGA M6' MHR, 6' (1.8 m)	26-238-25

VGA M10' MHR, 10' (3.0 m)	26-238-26

VGA M15' MHR, 15' (4.5 m)	26-238-27

VGA M25' MHR, 25' (7.6 m)	26-238-28

VGA M35' MHR, 35' (10.6 m)	26-238-16

VGA M50' MHR, 50' (15.2 m)	26-238-04

VGA M75' MHR, 75' (22.8 m)	26-238-05

VGA M100' MHR, 100' (30.4 m)	26-238-06

PRELIMINARY

MVX VGA A Matrix Switchers • Specifications, Part Numbers, Accessories A-7

Image 102

Extron electronic MVX VGA A manual Preliminary

Contents

Computer Video VGA and Audio Matrix Switchers MVX VGA a Sicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad Español FCC Class a Notice Preset button selects MVX VGA a Matrix Switchers Quick Start QS-1Input and output buttons select inputs QS-2 MVX VGA a Matrix Switchers Quick Start Saving or recalling a presetViewing and adjusting the audio level Creating a tie Table of Contents Table of Contents, cont’d Appendix a Specifications, Part Numbers, Accessories MVX VGA a Matrix Switchers Table of Contents Iii Iv MVX VGA a Matrix Switchers Table of Contents One About the MVX VGA a Matrix Switchers MVX VGA a Matrix Switchers IntroductionAbout this Manual Definitions Features Tie any input to any or all outputs Preliminary Preliminary Two UL requirements Mounting the SwitcherMVX VGA a Matrix Switchers Installation Mounting instructions Rear Panel Cabling and Views Computer OUT Sync Impedance switches Video connections Audio connections Ohms RS-232/RS-422 connection Connections for balanced and unbalanced audio outputs These Reset button Power connection Front Panel Configuration Port Be used for this connection Three Front Panel Controls and Indicators MVX VGA a Matrix Switchers OperationDefinitions Input and output buttons Sample label Operation, cont’d Control buttons Preliminary Controls Power Front Panel OperationsFront panel security lockouts Creating a configuration Example 1 Creating a set of video and audio ties Press and release the Esc button figure Select the outputs Example 2 Adding a tie to a set of video and audio ties Press and release the Input 5 button figurePress and release the Output 1 button figure 13 Press the Enter button Example 3 Removing a tie from a set of video and audio ties 15 Clear all selections Press and release the Output 4 button figure Press and release the Enter button figure Viewing a configuration 21 Clear all selections Preliminary Rgbhv button and the Audio button figure 24 Deselect Rgbhv to view audio ties only Muting and unmuting video and/or audio Example 5 Muting and unmuting an output 28 Select Rgbhv and audio 30 Unmute the outputs Using global presets 32 Preset locations, MVX 128 VGA a Example 6 Saving a preset LED blinks figure Example 7 Recalling a preset Press and release the Preset button figure 40 Select the preset Viewing and adjusting the input audio level 42 Audio gain and attenuation Example 8 Viewing and adjusting an input audio level 43 Clear all selections Preliminary 45 Select an input and read the audio level 47 Adjust the input audio level Viewing and adjusting the output volume Reading the displayed volume Audio output volume settings Example 9 Viewing and adjusting an output volume level 50 Clear all selections 52 Select output 54 Adjust the output audio volume Setting the front panel locks Executive modes Selecting Lock mode 2 or toggling between mode 2 and mode Performing a system reset from the front panel System reset does not replace user-installed firmware Selecting the rear panel Remote port protocol and baud rate Release the Control buttons 61 RS-232/RS-422 and baud rate selection Performing an absolute system reset from the rear panel Rear Panel Operations Performing a hard reset from the rear panel Optimizing the Audio Troubleshooting Configuration WorksheetsWorksheet example 1 System equipment Worksheet example 2 Daily configuration 66 Worksheet example 2 Daily configuration Worksheet example 3 Test configuration Preliminary Configuration worksheet Preset # Preliminary Four MVX VGA a Matrix Switchers Programmer’s Guide Serial PortsRear panel Remote port Host-to-Switcher Instructions Switcher-Initiated MessagesFront panel Configuration port Switcher Error Responses Using the Command/Response Table Command/Response Table for SIS Commands Symbol definitions Command Ascii command Response Additional Description % G InX! AudX$ Preliminary Exng EZG EX1$ *X1% ,X1 ,X1& ,X1* CP CpnX1$ CcpX1% ,X1 ,X1& ,X1 VX2XX2!AX2XX2 Five Matrix Switchers Control Program Installing the softwareMVX VGA a Matrix Switchers Matrix Software Using the Matrix Switcher Control software Comm port selection window Matrix Software, cont’d Sample program window complete Location of firmware upgrade files Updating firmware Downloading firmware upgrade files Open window Firmware Loader status indicator bar Windows buttons, drop boxes, and trash can Windows menusFile menu Tools menu 10 Status window Master-Reset selection Preferences menu Using Emulation mode Using the help systemButton-Label Generator Program Using the Button-Label Generator software 14 Extron’s Button-Label Generator window AppendixAA Specifications, Part Numbers, Accessories Specifications Sync Specifications, Part Numbers, Accessories, cont’d Accessories Part Numbers and AccessoriesMVX matrix switcher part numbers Included parts Male-to-male VGA molded connector cables Part number Male-to-female VGA molded connector cables Part numberMale-to-female VGA backshell connector cables Part number Cables Preliminary Button Labels Preliminary Preliminary Extron’s Warranty Asia Japan Extron Electronics, Europe Beeldschermweg 6C