PoleVault Systems | Extron electronic PVS 305SA instruction

				AILABLE:
			AV		®
ALSO					System
ALSO					.
	PoleVault Video com
The						.	.
Installation
					.extron
		itat		www
View		itat
View

PoleVault® Systems

(featuring the PVS 305SA)

Installation Guide

68-1691-01

Rev. A

08 09

Page 1

Image 1

Extron electronic PVS 305SA manual PoleVault Systems, Installation Guide

Contents

PoleVault Systems Installation Guide Safety Instructions English PrecautionsConsignes de Sécurité Français Sicherheitsanleitungen Deutsch Introduction PoleVault Systems Installation IntroductionFCC Class B Notice Introduction, contd PoleVault System installation and wiring overview PoleVault Systems Installation Introduction Planning Typical classroom installationRoom layout Room Introduction Planning, cont’d Example classroom installationLocation of the screen and projector ADA overhead and side clearance requirements Location of MediaLink Controller and Wall Plates Example classroom with four speaker installationLocation of source devices Cabling obstacles Inventory Introduction Inventory OverviewIncluded items PoleVault System Devices and Hardware, cont’d Introduction Inventory Overview, cont’d Optional installation hardwareItems not included Installation tools Outline of installation steps Installation OverviewPoleVault Systems Installation Installation PoleVault Systems Installation Installation Stage Stage One Install the Screen and ProjectorPCM 340 Projector Drop Ceiling Mount Slotted Pipe Supplied with PCM Install projector to verify location Installation Stage One, cont’dMark screen location 1a Mark the screen location Verify the image location 2f Slide and lock the projector onto the adjuster plate2e Attach the bracket to the projector Horizontal offset 5a Mark structural ceiling for lag eye bolt installation Preliminary safety hardware installationCut the ceiling tile 4b Take measurements with the PCM 340 on the T-frame Secure the Projector Drop Ceiling Mount to the ceiling Finish Projector Drop Ceiling Mount installation7a Attach turnbuckles at the corners 7c Hand tighten the turnbuckles Install the Screen Install the electrical box if required8a Install Raco box and plaster ring This stage involves installing the devices shown below Stage Two Install the Wall Plates and MLC 104 IP PlusMLC 104 IP Plus MediaLink Controller Cables Installation Stage Two, cont’dIR/RS-232 communications cable control cable RS-232 or to an IR emitter 1d Features for mud ring installation Install the mud ringsMLC 104 IP Plus mud ring 1c Insert the mud ring Pull the cables at the input locations Signal Cable Label color2c Pull the cables at each location MLC 104 IP Plus controller Install wall plates Wire stripping lengths Install MediaLink Controller4a Connecting the MLC to the switcher Connect the MLC to the projector with 4c Connect to the LAN using a CAT 5 cableAn RS-232 cable or IR emitter cable, as Appropriate 4e Secure the MLC 104 IP Plus to the mud ring Connections made to the MLC 104 IP Plus FF 120 Flat Field Ceiling Speakers Stage Three Install the FF 120 Ceiling Speakers Install the speaker on the drop ceiling Installation Stage Three, cont’d2h Attach safety cable Cut ceiling tile Pole captive screw connector Terminate the speaker cable for the PVS switcherStereo or dual mono output using parallel speaker wiring To terminate the cable, strip the end of the cable 0.2 inch This stage covers installing the devices shown below Stage Four Install the PMK 550 and the PVS 305SAPVS 305SA PoleVault Switcher PMK 550 Pole Mount Kit PoleVault Systems Installation Installation Stage 4 Install the PMK 550 base plate Pull the cables at the switcher location Installation Stage Four, cont’dSwitcher and projector cable overview 2b Gather the cables, pass them down the pipe BControl/power cable from the MLC 104 IP Plus Finish installing the Pole Mount kit4a Connect the cables to the switcher Connect the cables as follows to the PVS 305SA 4d Cable the projector 4b Reattach UPB bracket and 4c projector Configure the switcher MLS Switcher Configuration program Stage Five Configure the Switcher and the SystemGlobal configurator software Configure the system Global Configurator Installation Stage Five, cont’d 3c Check that an image is present, adjust as needed Loosen all pivot screws and adjust the vertical angleTest the system Adjust the configuration as necessary Final installationWhere installed, if necessary, adjust the sensitivity 3d Test the MLC configuration Align the arrows on the housing rim and the dome tab Optional Accessory Installation VoiceLift SystemAttach the Z bracket to the ceiling tile and the back plate Plug VoiceLift cable into PVS 305SA Open the sensor and loop a wire around the sensor Optional Accessory Installation Priority Page Sensor KitPriority Page Sensor Kit included parts UL-compliant junction box and cover Typical paging system with the PVS 305SA switcher Testing and Adjustment Procedure4 Sensitivity knob adjustment Reference Information PoleVault Systems Installation Reference Information Lbs 0.1 kg Wall or furniture mountable with included Decora wall plate Extron PCM Reference Information, cont’d PVS 305SA specific symbol definitions SIS CommandsSIS Command/Response Table Ascii Telnet PoleVault Systems Installation Basic SIS Commands Extron USA West