FF 120 Flat Field Ceiling Speakers

Stage Three — Install the FF 120 Ceiling Speakers

Stage 3

This stage involves installing the devices shown below.

FF 120 Speaker (2)

Terminal Cover

Seismic Tabs (3 per side)

Cable Clamps (2)

Anchor Rings (2)

T-rails (2)

Where it goes: Installs in ceiling tiles at predetermined location for best acoustics. Connects to switcher.

What it does: Receives and outputs audio signal from PVS 305SA switcher

Cables

Speaker Installation:

• Speaker cable (connects ceiling speakers to the PVS 305SA switcher)

SPK 18, 35 ft

PoleVault Systems Installation • Installation — Stage 2

2-16

Page 27

Image 27

Extron electronic PVS 305SA manual Stage Three Install the FF 120 Ceiling Speakers, FF 120 Flat Field Ceiling Speakers

Contents

PoleVault Systems Installation Guide Sicherheitsanleitungen Deutsch PrecautionsSafety Instructions English Consignes de Sécurité Français PoleVault Systems Installation Introduction IntroductionFCC Class B Notice Introduction, contd PoleVault System installation and wiring overview Room Typical classroom installationPoleVault Systems Installation Introduction Planning Room layout ADA overhead and side clearance requirements Example classroom installationIntroduction Planning, cont’d Location of the screen and projector Cabling obstacles Example classroom with four speaker installationLocation of MediaLink Controller and Wall Plates Location of source devices Introduction Inventory Overview InventoryIncluded items PoleVault System Devices and Hardware, cont’d Optional installation hardware Introduction Inventory Overview, cont’dItems not included Installation tools Installation Overview Outline of installation stepsPoleVault Systems Installation Installation Slotted Pipe Supplied with PCM Stage One Install the Screen and ProjectorPoleVault Systems Installation Installation Stage PCM 340 Projector Drop Ceiling Mount 1a Mark the screen location Installation Stage One, cont’dInstall projector to verify location Mark screen location Horizontal offset 2f Slide and lock the projector onto the adjuster plateVerify the image location 2e Attach the bracket to the projector 4b Take measurements with the PCM 340 on the T-frame Preliminary safety hardware installation5a Mark structural ceiling for lag eye bolt installation Cut the ceiling tile 7c Hand tighten the turnbuckles Finish Projector Drop Ceiling Mount installationSecure the Projector Drop Ceiling Mount to the ceiling 7a Attach turnbuckles at the corners Install the electrical box if required Install the Screen8a Install Raco box and plaster ring Stage Two Install the Wall Plates and MLC 104 IP Plus This stage involves installing the devices shown belowMLC 104 IP Plus MediaLink Controller RS-232 or to an IR emitter Installation Stage Two, cont’dCables IR/RS-232 communications cable control cable 1c Insert the mud ring Install the mud rings1d Features for mud ring installation MLC 104 IP Plus mud ring Signal Cable Label color Pull the cables at the input locations2c Pull the cables at each location MLC 104 IP Plus controller Install wall plates Install MediaLink Controller Wire stripping lengths4a Connecting the MLC to the switcher Appropriate 4c Connect to the LAN using a CAT 5 cableConnect the MLC to the projector with An RS-232 cable or IR emitter cable, as 4e Secure the MLC 104 IP Plus to the mud ring Connections made to the MLC 104 IP Plus FF 120 Flat Field Ceiling Speakers Stage Three Install the FF 120 Ceiling Speakers Cut ceiling tile Installation Stage Three, cont’dInstall the speaker on the drop ceiling 2h Attach safety cable To terminate the cable, strip the end of the cable 0.2 inch Terminate the speaker cable for the PVS switcherPole captive screw connector Stereo or dual mono output using parallel speaker wiring PMK 550 Pole Mount Kit Stage Four Install the PMK 550 and the PVS 305SAThis stage covers installing the devices shown below PVS 305SA PoleVault Switcher PoleVault Systems Installation Installation Stage 4 Install the PMK 550 base plate 2b Gather the cables, pass them down the pipe Installation Stage Four, cont’dPull the cables at the switcher location Switcher and projector cable overview Connect the cables as follows to the PVS 305SA Finish installing the Pole Mount kitBControl/power cable from the MLC 104 IP Plus 4a Connect the cables to the switcher 4d Cable the projector 4b Reattach UPB bracket and 4c projector Stage Five Configure the Switcher and the System Configure the switcher MLS Switcher Configuration programGlobal configurator software Configure the system Global Configurator Installation Stage Five, cont’d Loosen all pivot screws and adjust the vertical angle 3c Check that an image is present, adjust as neededTest the system 3d Test the MLC configuration Final installationAdjust the configuration as necessary Where installed, if necessary, adjust the sensitivity Plug VoiceLift cable into PVS 305SA Optional Accessory Installation VoiceLift SystemAlign the arrows on the housing rim and the dome tab Attach the Z bracket to the ceiling tile and the back plate UL-compliant junction box and cover Optional Accessory Installation Priority Page Sensor KitOpen the sensor and loop a wire around the sensor Priority Page Sensor Kit included parts Testing and Adjustment Procedure Typical paging system with the PVS 305SA switcher4 Sensitivity knob adjustment Reference Information PoleVault Systems Installation Reference Information Lbs 0.1 kg Wall or furniture mountable with included Decora wall plate Extron PCM Reference Information, cont’d PoleVault Systems Installation Basic SIS Commands SIS CommandsPVS 305SA specific symbol definitions SIS Command/Response Table Ascii Telnet Extron USA West