4d Cable the projector

Installation — Stage Four, cont’d

b.Screw the UPB 25 adjuster plate back onto the base of the pipe and tuck the cables through the back of the adapter plate.

c.Replace the projector (with the UPB 25 bracket attached) on the adjuster plate and tighten the adjuster plate locking nuts.

4b Reattach UPB bracket and 4c projector

d.Connect the switcher’s VGA and RCA cables to the projector.

e.Connect the IR/RS-232 projector control cable to the projector.

f.Connect the projector power cord, ensuring the cord exits via the cable notch in the PMK cover plate.

2-23 PoleVault Systems Installation • Installation — Stage 4

Page 34

Image 34

Extron electronic PVS 305SA manual 4b Reattach UPB bracket and 4c projector, 4d Cable the projector

Contents

Installation Guide PoleVault Systems Consignes de Sécurité Français PrecautionsSafety Instructions English Sicherheitsanleitungen Deutsch Introduction PoleVault Systems Installation IntroductionFCC Class B Notice PoleVault System installation and wiring overview Introduction, contd Room layout Typical classroom installationPoleVault Systems Installation Introduction Planning Room Location of the screen and projector Example classroom installationIntroduction Planning, cont’d ADA overhead and side clearance requirements Location of source devices Example classroom with four speaker installationLocation of MediaLink Controller and Wall Plates Cabling obstacles Inventory Introduction Inventory OverviewIncluded items PoleVault System Devices and Hardware, cont’d Introduction Inventory Overview, cont’d Optional installation hardwareItems not included Installation tools Outline of installation steps Installation OverviewPoleVault Systems Installation Installation PCM 340 Projector Drop Ceiling Mount Stage One Install the Screen and ProjectorPoleVault Systems Installation Installation Stage Slotted Pipe Supplied with PCM Mark screen location Installation Stage One, cont’dInstall projector to verify location 1a Mark the screen location 2e Attach the bracket to the projector 2f Slide and lock the projector onto the adjuster plateVerify the image location Horizontal offset Cut the ceiling tile Preliminary safety hardware installation5a Mark structural ceiling for lag eye bolt installation 4b Take measurements with the PCM 340 on the T-frame 7a Attach turnbuckles at the corners Finish Projector Drop Ceiling Mount installationSecure the Projector Drop Ceiling Mount to the ceiling 7c Hand tighten the turnbuckles Install the Screen Install the electrical box if required8a Install Raco box and plaster ring This stage involves installing the devices shown below Stage Two Install the Wall Plates and MLC 104 IP PlusMLC 104 IP Plus MediaLink Controller IR/RS-232 communications cable control cable Installation Stage Two, cont’dCables RS-232 or to an IR emitter MLC 104 IP Plus mud ring Install the mud rings1d Features for mud ring installation 1c Insert the mud ring Pull the cables at the input locations Signal Cable Label color2c Pull the cables at each location Install wall plates MLC 104 IP Plus controller Wire stripping lengths Install MediaLink Controller4a Connecting the MLC to the switcher An RS-232 cable or IR emitter cable, as 4c Connect to the LAN using a CAT 5 cableConnect the MLC to the projector with Appropriate Connections made to the MLC 104 IP Plus 4e Secure the MLC 104 IP Plus to the mud ring Stage Three Install the FF 120 Ceiling Speakers FF 120 Flat Field Ceiling Speakers 2h Attach safety cable Installation Stage Three, cont’dInstall the speaker on the drop ceiling Cut ceiling tile Stereo or dual mono output using parallel speaker wiring Terminate the speaker cable for the PVS switcherPole captive screw connector To terminate the cable, strip the end of the cable 0.2 inch PVS 305SA PoleVault Switcher Stage Four Install the PMK 550 and the PVS 305SAThis stage covers installing the devices shown below PMK 550 Pole Mount Kit Install the PMK 550 base plate PoleVault Systems Installation Installation Stage 4 Switcher and projector cable overview Installation Stage Four, cont’dPull the cables at the switcher location 2b Gather the cables, pass them down the pipe 4a Connect the cables to the switcher Finish installing the Pole Mount kitBControl/power cable from the MLC 104 IP Plus Connect the cables as follows to the PVS 305SA 4b Reattach UPB bracket and 4c projector 4d Cable the projector Configure the switcher MLS Switcher Configuration program Stage Five Configure the Switcher and the SystemGlobal configurator software Installation Stage Five, cont’d Configure the system Global Configurator 3c Check that an image is present, adjust as needed Loosen all pivot screws and adjust the vertical angleTest the system Where installed, if necessary, adjust the sensitivity Final installationAdjust the configuration as necessary 3d Test the MLC configuration Attach the Z bracket to the ceiling tile and the back plate Optional Accessory Installation VoiceLift SystemAlign the arrows on the housing rim and the dome tab Plug VoiceLift cable into PVS 305SA Priority Page Sensor Kit included parts Optional Accessory Installation Priority Page Sensor KitOpen the sensor and loop a wire around the sensor UL-compliant junction box and cover Typical paging system with the PVS 305SA switcher Testing and Adjustment Procedure4 Sensitivity knob adjustment PoleVault Systems Installation Reference Information Reference Information Wall or furniture mountable with included Decora wall plate Lbs 0.1 kg Reference Information, cont’d Extron PCM SIS Command/Response Table Ascii Telnet SIS CommandsPVS 305SA specific symbol definitions PoleVault Systems Installation Basic SIS Commands Extron USA West

Extron electronic PVS 305SA 4b Reattach UPB bracket and 4c projector, 4d Cable the projector

Models: PVS 305SA

Installation — Stage Four, cont’d

4b Reattach UPB bracket and 4c projector

4d Cable the projector

2-23 PoleVault Systems Installation • Installation — Stage 4