Reference Information, cont’d

Extron

PMK 550

Easy Installation Pole Mount Kit

weight 2.4 lbs (1.2 kg)

Extron

PCM 340

Projector Drop Ceiling Mount

(including Slotted Projector

Mount Pole)

weight 4.5 lbs (2.0 kg)

Power Supply

(included with PVS switcher)

weight 0.9 lbs (0.4 kg)

CONFIG

2	INPUT
	3SELECTION

Extron

PVS 305SA

PoleVault® Switcher

weight 2.5 lbs (1.1 kg)

	5
AUX	AUDIO
	AUDIO

INPUT
PEAKAUDIO		LEVELPOLEV PVS
NORMAL		LEVELPOLEV PVS		305SA
NORMAL	MIC		AULT
SIGNAL			ADJUST
	VO	ICELIFT	PEAK	SWITCHER
		ICELIFT	NORMAL	GING
			SIGNAL	SENSOR
				SENSITIVITY

Total weight (without projector or electrical boxes)*

14 -16 lbs (6.4 -7.3 kg)

*Projector weight must not exceed 25 lbs (11.3 kg)

Extron

UPB 25

Universal Projector Mounting Bracket

weight 3.7 lbs (1.7 kg)

Ceiling mount installation diagram (with item weights) for PoleVault System

4-3 PoleVault Systems Installation • Reference Information

Page 44

Image 44

Extron electronic PVS 305SA manual Reference Information, cont’d, Extron PCM

Contents

Installation Guide PoleVault Systems Precautions Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen Deutsch FCC Class B Notice PoleVault Systems Installation IntroductionIntroduction PoleVault System installation and wiring overview Introduction, contd Typical classroom installation PoleVault Systems Installation Introduction PlanningRoom layout Room Example classroom installation Introduction Planning, cont’dLocation of the screen and projector ADA overhead and side clearance requirements Example classroom with four speaker installation Location of MediaLink Controller and Wall PlatesLocation of source devices Cabling obstacles Included items Introduction Inventory OverviewInventory PoleVault System Devices and Hardware, cont’d Items not included Optional installation hardwareIntroduction Inventory Overview, cont’d Installation tools PoleVault Systems Installation Installation Installation OverviewOutline of installation steps Stage One Install the Screen and Projector PoleVault Systems Installation Installation StagePCM 340 Projector Drop Ceiling Mount Slotted Pipe Supplied with PCM Installation Stage One, cont’d Install projector to verify locationMark screen location 1a Mark the screen location 2f Slide and lock the projector onto the adjuster plate Verify the image location2e Attach the bracket to the projector Horizontal offset Preliminary safety hardware installation 5a Mark structural ceiling for lag eye bolt installationCut the ceiling tile 4b Take measurements with the PCM 340 on the T-frame Finish Projector Drop Ceiling Mount installation Secure the Projector Drop Ceiling Mount to the ceiling7a Attach turnbuckles at the corners 7c Hand tighten the turnbuckles 8a Install Raco box and plaster ring Install the electrical box if requiredInstall the Screen MLC 104 IP Plus MediaLink Controller Stage Two Install the Wall Plates and MLC 104 IP PlusThis stage involves installing the devices shown below Installation Stage Two, cont’d CablesIR/RS-232 communications cable control cable RS-232 or to an IR emitter Install the mud rings 1d Features for mud ring installationMLC 104 IP Plus mud ring 1c Insert the mud ring 2c Pull the cables at each location Signal Cable Label colorPull the cables at the input locations Install wall plates MLC 104 IP Plus controller 4a Connecting the MLC to the switcher Install MediaLink ControllerWire stripping lengths 4c Connect to the LAN using a CAT 5 cable Connect the MLC to the projector withAn RS-232 cable or IR emitter cable, as Appropriate Connections made to the MLC 104 IP Plus 4e Secure the MLC 104 IP Plus to the mud ring Stage Three Install the FF 120 Ceiling Speakers FF 120 Flat Field Ceiling Speakers Installation Stage Three, cont’d Install the speaker on the drop ceiling2h Attach safety cable Cut ceiling tile Terminate the speaker cable for the PVS switcher Pole captive screw connectorStereo or dual mono output using parallel speaker wiring To terminate the cable, strip the end of the cable 0.2 inch Stage Four Install the PMK 550 and the PVS 305SA This stage covers installing the devices shown belowPVS 305SA PoleVault Switcher PMK 550 Pole Mount Kit Install the PMK 550 base plate PoleVault Systems Installation Installation Stage 4 Installation Stage Four, cont’d Pull the cables at the switcher locationSwitcher and projector cable overview 2b Gather the cables, pass them down the pipe Finish installing the Pole Mount kit BControl/power cable from the MLC 104 IP Plus4a Connect the cables to the switcher Connect the cables as follows to the PVS 305SA 4b Reattach UPB bracket and 4c projector 4d Cable the projector Global configurator software Stage Five Configure the Switcher and the SystemConfigure the switcher MLS Switcher Configuration program Installation Stage Five, cont’d Configure the system Global Configurator Test the system Loosen all pivot screws and adjust the vertical angle3c Check that an image is present, adjust as needed Final installation Adjust the configuration as necessaryWhere installed, if necessary, adjust the sensitivity 3d Test the MLC configuration Optional Accessory Installation VoiceLift System Align the arrows on the housing rim and the dome tabAttach the Z bracket to the ceiling tile and the back plate Plug VoiceLift cable into PVS 305SA Optional Accessory Installation Priority Page Sensor Kit Open the sensor and loop a wire around the sensorPriority Page Sensor Kit included parts UL-compliant junction box and cover 4 Sensitivity knob adjustment Testing and Adjustment ProcedureTypical paging system with the PVS 305SA switcher PoleVault Systems Installation Reference Information Reference Information Wall or furniture mountable with included Decora wall plate Lbs 0.1 kg Reference Information, cont’d Extron PCM SIS Commands PVS 305SA specific symbol definitionsSIS Command/Response Table Ascii Telnet PoleVault Systems Installation Basic SIS Commands Extron USA West