Freescale Semiconductor MMDS0508 4.6.1 Communication Device Specification

MMDS Target Component

4.6 Communication Configuration

4–28 MMDS0508 Target Interface

Figure 4.6 MotoSIL Communication Configuration

Make sure that host-computer parameter values are correct; make sure that the serial-

communication setting is correct. Otherwise, communication between the debugger

and the target is not possible.

4.6.1 Communication Device Specification

If the host and target are not connected, or if the communication device is not properly

indicated, the Communications Device Specification dialog box appears as shown in

Figure 4.7 :

Figure 4.7 Communication Device Specification

Type the name of an available communication device in the Communication Device

edit box, use the drop-down control to set the baud rate, then click Connect. (The

default communication device is COM1.)

Once connection succeeds, the debugger saves the settings as defaults for later debug

sessions. Should the connection fail, a message box so informs you, so that you can

define a new communication device. To quit the dialog box and the environment, click

Cancel.

Freescale Semiconductor, Inc.

For More Information: www.freescale.com

Contents

Main How to Contact Metrowerks Table of Contents 1 General Description 5 2Installation 9 3 Connector Information 17 4 MMDS Target Component 23 A Appendix 59 General Description 1.1 Introduction 1.2 MMDS Features 1.3 System Components Page Page Installation Installation 2.1 Introduction Page 2.2 Configuring the Platform Board 2.2.1 Factory Test Header (J1) 2.2.2 Port Voltage Control Headers (J2J4) 2.3 Installing the EM 2.4 Removing the EM 2.5 Making Cable Connections 2.5.1 Host Computer Connection 2.5.2 Bus State Analyzer Connection 2.5.3 Target Cable Connection 2.5.4 Power Connection Page Connector Information 3.1 Introduction 3.2 Reset Switch 3.3 RS232 Serial Connector 3.4 Logic Cables and Connectors Page 3.5 Power Supply Fuse Replacement Page Page MMDS Target Component 4.1 Introduction 4.2 General 4.2.1 MMDS0508 4.2.2 Configuration 4.3 Definitions, Acronyms and Abbreviations 4.4 Interfacing Your System and the Target 4.5 Loading the MMDS0508 Target 4.6 Communication Configuration 4.6.1 Communication Device Specification 4.6.2 Data Format 4.7 The Debugger Status Bar for the MMDS 4.8 MMDS0508 Menu Entries 4.8.1 Communication Baud Rate 4.8.1.1 Communication 4.8.1.2 Maximum Baud Rate 4.8.1.3 Show Protocol 4.8.2 Memory Configuration 4.8.3 Personality (.MEM) Files Page 4.8.3.1 Dual-Port RAM 4.8.3.2 Memory 4.8.4 Signals Emulation 4.8.4.1 MCU Clock 4.8.4.2 Reset 4.8.5 Bus Tracing 4.9 Default Target Setup 4.9.1 Motorola ESL Parameters 4.9.1.1 COMDEV 4.9.1.2 BAUDRATE 1200, 2400, 4800, 9600, 19200, 28800, 38400, 57600, 115200. 4.10 Bus Analyzer 4.10.1 Introduction to the Bus Analyzer 4.10.1.1 Watchpoints 4.10.1.2 Trace Modes 4.10.1.3 Trace Buffer 4.10.2 Using the Bus Analyzer 4.10.2.1 The Trace window popup menu 4.10.2.2 Trigger Setup 4.10.2.3 Sequencer Setup 4.10.2.4 Non-Triggered Modes 4.10.2.5 Counted Modes 4.10.2.6 Triggered Modes/Sequential Event Mode 4.10.2.7 Counted/Sequential Recording Mode 4.10.2.8 Time Tag Clock Setup 4.10.3 Collecting Data 4.10.3.7 Recording Bus Data 4.10.3.8 Trigger Event 4.10.4 Viewing Collected Data 4.10.4.1 View Cycles 4.10.4.2 Textual, Graphical or Instructions 4.10.4.3 Textual Display 4.10.4.4 Instructions Only Display 4.10.4.5 Graphical Display Page Page 4.10.5 Scrolling the Display 4.10.5.1 Search for a Frame 4.10.5.2 Search for Events 4.10.5.3 Search for a Pattern Page 4.10.6 Dumping the Bus analyzer data to a file 4.10.6.1 Dump File Page A Appendix A.1 MMDS Commands A.1.1 Baud Rate Command BAUD A.1.1.1 Short Description A.1.2 Trigger Commands CT A.1.2.1 Short Description A.1.2.2 Syntax A.1.2.3 Description ST A.1.2.4 Short Description A.1.2.5 Syntax A.1.2.6 Description Page Page TD A.1.2.7 Short Description A.1.2.8 Syntax A.1.2.9 Description TE A.1.2.10 Short Description A.1.2.11 Syntax A.1.2.12 Description A.1.3 Bus Analyzer Commands Page Page A.1.3.15 Description LT A.1.3.16 Short Description A.1.3.17 Syntax A.1.3.18 Description SC A.1.3.19 Short Description A.1.3.20 Syntax A.1.3.21 Description SP A.1.3.22 Short Description A.1.3.23 Description A.1.3.24 Syntax Page Page SQ A.1.3.25 Short Description A.1.3.26 Syntax A.1.3.27 Description TT A.1.3.28 Short Description A.1.3.29 Syntax A.1.3.30 Description VA A.1.3.31 Short Description A.1.3.32 Syntax A.1.3.33 Description A.1.4 Target Signal Emulation Commands A.1.5 Reset Commands A.1.6 Other Commands A.1.6.3 Description MEM A.1.6.4 Short Description A.1.6.5 Syntax A.1.6.6 Description OSC A.1.6.7 Short Description A.1.6.8 Syntax A.1.6.9 Description Page A.1.6.15 Description Index Symbols A B C M N O P R T V W Z