Graphical Display | Freescale Semiconductor MMDS0508 manual

Freescale Semiconductor, Inc.

MMDS Target Component

4.10 Bus Analyzer

Figure 4.21 Trace Instructions Only Format Display

4.10.4.5 Graphical Display

The figure below shows the graphical display of bus analyzer data. Selections of the Trace menu let you switch between formats easily, at any time. The left column lists data items. The next column lists the data values for the current frame. The rest of the display presents those data values graphically, or with greater resolution. In a graphical display, the marker consists of two vertical bars that enclose the information of the current frame.

4.10.4.5.1 Zoom In or Out

The graphical display shown in Figure 4.22 lets you zoom in, to see more details, or zoom out, for a better general view. Zoom in and Zoom out are selections of the Trace popup menu.

Other ways to zoom in are choosing the Trace>Zoom In menu selection or pressing the 'I' key of the keyboard.

4–50	MMDS0508 Target Interface

For More Information: www.freescale.com

Image 50

Freescale Semiconductor MMDS0508 manual Graphical Display, Zoom In or Out

Contents

MMDS0508 Target Interface Freescale Semiconductor, Inc How to Contact Metrowerks Table of Contents Appendix Mmds Features Introduction System Components Freescale Semiconductor, Inc System Components MMDS0508 Target Interface Installation M68MMDS0508 Station Module Right Side Configuring the Platform Board Factory Test Header J1 Port Voltage Control Headers J2-J4 Factory Test Header J1 Installing the EM Removing the EM Bus State Analyzer Connection Making Cable ConnectionsHost Computer Connection Power Connection Target Cable Connection Making Cable Connections MMDS0508 Target Interface Reset Switch RS232 Serial Connector Logic Cables and Connectors Serial Connector and Cable Pin Assignments Pod and Logic Cable Pin Assignments Power Supply Fuse Replacement Power Switch/Connector Assembly Freescale Semiconductor, Inc Power Supply Fuse Replacement MMDS0508 Target Interface Mmds Target Component MMDS0508 ConfigurationGeneral Definitions, Acronyms and Abbreviations Interfacing Your System and the Target Loading the MMDS0508 Target Hardware connection Communication Configuration Loading MotoSIL Target Communication Device Specification MotoSIL Communication Configuration Data Format Debugger Status Bar forMMDS0508 Menu Entries Communication Baud Rate Communication Show Protocol Memory ConfigurationMaximum Baud Rate Personality .MEM Files 0nnnnVxx.MEM 12 Error Message Memory Signals EmulationDual-Port RAM MCU Clock ResetBus Tracing Comdev Default Target SetupMotorola ESL Parameters Baudrate Bus AnalyzerIntroduction to the Bus Analyzer Showprot Trace Modes Using the Bus AnalyzerWatchpoints Trace Buffer Trace window popup menu 15 Bus Analyzer Trigger Setup 17 Bus Analyzer Trigger Setup Sequencer Setup Non-Triggered Modes Continuous All Cycles Triggered Modes/Sequential Event Mode Counted Modes Counted/Sequential Recording Mode Time Tag Clock Setup Clock Frequency Collecting Data Trigger Event Viewing Collected DataRecording Bus Data View Cycles Textual Display Events Time Tag Control SignalsInstructions Only Display Time Measuring Graphical Display Zoom In or Out 22 Trace Zoom Display ShowLocation Add / Remove Items in the Trace Window Scrolling the Display Search for a Frame Forward Search for EventsOK Button Backward Search for a Pattern Previous Event Previous Pattern Cancel ButtonNext Pattern Dumping the Bus analyzer data to a file Dump File 31 Analyzer Dump Only Frame Short Description Mmds CommandsBaud Rate Command Syntax Trigger Commands Set trigger Data RED ORG YEL GRN Examples Disables triggers a and B Bus Analyzer Commands Darm GP B Log trace Open the logging file Sets the 8 Mhz oscillator as the time tag clock source Address SP 8 Set sequencer Display time tag difference VA MODE=MIX INS Graph Target Signal Emulation Commands Reset Commands Other Commands MEM OSC Protocol Disables the real time memory block Index IDX-84 MMDS0508 Target Interface IDX-85 IDX-86