Mmds Commands, Baud Rate Command | Freescale Semiconductor MMDS0508

Freescale Semiconductor, Inc.

A

Appendix

A.1 MMDS Commands

This section describes MMDS-specific commands.

Use MMDS-specific commands as you would any other commands, typing them in the Command Line component, or inserting them into a command file.

For further details about debugger commands, please see the debugger manual sections Appendix, Debugger Commands and Command Line Component.

A.1.1 Baud Rate Command

BAUD

A.1.1.1 Short Description

sets the communication baud rate.

A.1.1.2 Syntax

BAUD [rate]

rate: Specifies the new baud rate; must be one of these decimal integer constants: 1200, 2400, 4800, 9600, 19200, 28800, 38400, 57600, 115200.

A.1.1.3 Description

The BAUD command sets or displays the baud rate for communication between the system controller and the host computer. For maximum performance, the baud rate should be as high as the host computer can accommodate. The maximum rate is 115200; the default baud rate is 9600.

MMDS0508 Target Interface

A–59

For More Information: www.freescale.com

Image 59

Freescale Semiconductor MMDS0508 manual Mmds Commands, Baud Rate Command, Short Description, Syntax

Contents

Freescale Semiconductor, Inc MMDS0508 Target Interface How to Contact Metrowerks Table of Contents Appendix Introduction Mmds Features System Components Freescale Semiconductor, Inc System Components MMDS0508 Target Interface Installation M68MMDS0508 Station Module Right Side Factory Test Header J1 Configuring the Platform Board Factory Test Header J1 Port Voltage Control Headers J2-J4 Removing the EM Installing the EM Bus State Analyzer Connection Making Cable ConnectionsHost Computer Connection Target Cable Connection Power Connection Making Cable Connections MMDS0508 Target Interface RS232 Serial Connector Reset Switch Serial Connector and Cable Pin Assignments Logic Cables and Connectors Pod and Logic Cable Pin Assignments Power Switch/Connector Assembly Power Supply Fuse Replacement Freescale Semiconductor, Inc Power Supply Fuse Replacement MMDS0508 Target Interface Mmds Target Component MMDS0508 ConfigurationGeneral Interfacing Your System and the Target Definitions, Acronyms and Abbreviations Hardware connection Loading the MMDS0508 Target Loading MotoSIL Target Communication Configuration MotoSIL Communication Configuration Communication Device Specification Data Format Debugger Status Bar forMMDS0508 Menu Entries Communication Communication Baud Rate Show Protocol Memory ConfigurationMaximum Baud Rate 0nnnnVxx.MEM Personality .MEM Files 12 Error Message Memory Signals EmulationDual-Port RAM MCU Clock ResetBus Tracing Comdev Default Target SetupMotorola ESL Parameters Showprot Bus AnalyzerIntroduction to the Bus Analyzer Baudrate Trace Buffer Using the Bus AnalyzerWatchpoints Trace Modes 15 Bus Analyzer Trace window popup menu 17 Bus Analyzer Trigger Setup Trigger Setup Sequencer Setup Continuous All Cycles Non-Triggered Modes Counted Modes Triggered Modes/Sequential Event Mode Counted/Sequential Recording Mode Clock Frequency Time Tag Clock Setup Collecting Data View Cycles Viewing Collected DataRecording Bus Data Trigger Event Events Textual Display Time Measuring Control SignalsInstructions Only Display Time Tag Zoom In or Out Graphical Display 22 Trace Zoom Display Add / Remove Items in the Trace Window ShowLocation Search for a Frame Scrolling the Display Backward Search for EventsOK Button Forward Previous Event Search for a Pattern Previous Pattern Cancel ButtonNext Pattern Dump File Dumping the Bus analyzer data to a file 31 Analyzer Dump Only Frame Syntax Mmds CommandsBaud Rate Command Short Description Trigger Commands Set trigger Data RED ORG YEL GRN Examples Disables triggers a and B Bus Analyzer Commands Darm GP B Log trace Open the logging file Sets the 8 Mhz oscillator as the time tag clock source Address SP 8 Set sequencer Display time tag difference VA MODE=MIX INS Graph Reset Commands Target Signal Emulation Commands Other Commands MEM OSC Protocol Disables the real time memory block Index IDX-84 MMDS0508 Target Interface IDX-85 IDX-86