Protocol | Freescale Semiconductor MMDS0508 instruction

Freescale Semiconductor, Inc.

Appendix

MMDS Commands

Example:

OSC OSC8MHZ // Use the 8 Mhz internal

emulator clock.

PROTOCOL

A.1.6.10 Short Description

controls Show Protocol functionality.

A.1.6.11 Syntax

PROTOCOL [ON OFF]

ON: Reports commands and responses in the command line window (default value for this command).

OFF: Does not report commands or responses in the command line window; does not log commands or responses in the log file.

A.1.6.12 Description

The PROTOCOL command controls reporting commands and responses in the command line window. Entering this command without a parameter value has the same effect as entering the command with the parameter value ON.

RTMEM

A.1.6.13 Short Description

configures real time memory.

A.1.6.14 Syntax

RTMEM address [;E;D]

address: base address of a real time memory block (default is 0).

;E: Enables the real time memory block (the default for this command).

MMDS0508 Target Interface

A–81

For More Information: www.freescale.com

Image 81

Freescale Semiconductor MMDS0508 manual Protocol

Contents

Freescale Semiconductor, Inc MMDS0508 Target Interface How to Contact Metrowerks Table of Contents Appendix Introduction Mmds Features System Components Freescale Semiconductor, Inc System Components MMDS0508 Target Interface Installation M68MMDS0508 Station Module Right Side Factory Test Header J1 Configuring the Platform Board Factory Test Header J1 Port Voltage Control Headers J2-J4 Removing the EM Installing the EM Making Cable Connections Host Computer ConnectionBus State Analyzer Connection Target Cable Connection Power Connection Making Cable Connections MMDS0508 Target Interface RS232 Serial Connector Reset Switch Serial Connector and Cable Pin Assignments Logic Cables and Connectors Pod and Logic Cable Pin Assignments Power Switch/Connector Assembly Power Supply Fuse Replacement Freescale Semiconductor, Inc Power Supply Fuse Replacement MMDS0508 Target Interface Mmds Target Component Configuration GeneralMMDS0508 Interfacing Your System and the Target Definitions, Acronyms and Abbreviations Hardware connection Loading the MMDS0508 Target Loading MotoSIL Target Communication Configuration MotoSIL Communication Configuration Communication Device Specification Debugger Status Bar for MMDS0508 Menu EntriesData Format Communication Communication Baud Rate Memory Configuration Maximum Baud RateShow Protocol 0nnnnVxx.MEM Personality .MEM Files 12 Error Message Signals Emulation Dual-Port RAMMemory Reset Bus TracingMCU Clock Default Target Setup Motorola ESL ParametersComdev Introduction to the Bus Analyzer Bus AnalyzerBaudrate Showprot Watchpoints Using the Bus AnalyzerTrace Modes Trace Buffer 15 Bus Analyzer Trace window popup menu 17 Bus Analyzer Trigger Setup Trigger Setup Sequencer Setup Continuous All Cycles Non-Triggered Modes Counted Modes Triggered Modes/Sequential Event Mode Counted/Sequential Recording Mode Clock Frequency Time Tag Clock Setup Collecting Data Recording Bus Data Viewing Collected DataTrigger Event View Cycles Events Textual Display Instructions Only Display Control SignalsTime Tag Time Measuring Zoom In or Out Graphical Display 22 Trace Zoom Display Add / Remove Items in the Trace Window ShowLocation Search for a Frame Scrolling the Display OK Button Search for EventsForward Backward Previous Event Search for a Pattern Cancel Button Next PatternPrevious Pattern Dump File Dumping the Bus analyzer data to a file 31 Analyzer Dump Only Frame Baud Rate Command Mmds CommandsShort Description Syntax Trigger Commands Set trigger Data RED ORG YEL GRN Examples Disables triggers a and B Bus Analyzer Commands Darm GP B Log trace Open the logging file Sets the 8 Mhz oscillator as the time tag clock source Address SP 8 Set sequencer Display time tag difference VA MODE=MIX INS Graph Reset Commands Target Signal Emulation Commands Other Commands MEM OSC Protocol Disables the real time memory block Index IDX-84 MMDS0508 Target Interface IDX-85 IDX-86