Bus Analyzer, Baudrate, Showprot | Freescale Semiconductor MMDS0508

Freescale Semiconductor, Inc.

MMDS Target Component

4.10 Bus Analyzer

For a PC: Any valid communication device (COM1,COM2,etc.).

Example:COMDEV=COM2

For SUN:Any valid communication device (/dev/ttya, etc.).

Example:comdev=/dev/ttyb

4.9.1.2 BAUDRATE

This parameter specifies the communication baud rate between the host computer and the target system. The debugger default is 9600 baud, but you may set any of these baud rates:

1200, 2400, 4800, 9600, 19200, 28800, 38400, 57600, 115200.

Example:BAUDRAUTE=19200

4.9.1.3 SHOWPROT

This parameter specifies whether to report commands and responses in the command line window. To have the system report the commands and responses, give this parameter the value 1. To have the system not do this reporting, give this parameter the value 0. (Another way to specify reporting is checking the Show Protocol checkbox of the Communication Device Specification dialog box.)

Please see the section Communication Configuration, Communication Device Specification.

4.10 Bus Analyzer

4.10.1 Introduction to the Bus Analyzer

Except for emulating the target-system MCU, the most important feature that a microcontroller development tool can offer is analyzing program execution activities on the target MCU bus. This analysis lets you determine what is occurring in a system, without actually affecting the system.

NOTE	The MMDS0508 bus analyzer shows the logical state of the MCU
	bus. It does not show signal hold or setup times.

MMDS0508 Target Interface

4–37

For More Information: www.freescale.com

Image 37

Freescale Semiconductor MMDS0508 manual Introduction to the Bus Analyzer, Baudrate, Showprot

Contents

Freescale Semiconductor, Inc MMDS0508 Target Interface How to Contact Metrowerks Table of Contents Appendix Introduction Mmds Features System Components Freescale Semiconductor, Inc System Components MMDS0508 Target Interface Installation M68MMDS0508 Station Module Right Side Factory Test Header J1 Configuring the Platform Board Factory Test Header J1 Port Voltage Control Headers J2-J4 Removing the EM Installing the EM Host Computer Connection Making Cable ConnectionsBus State Analyzer Connection Target Cable Connection Power Connection Making Cable Connections MMDS0508 Target Interface RS232 Serial Connector Reset Switch Serial Connector and Cable Pin Assignments Logic Cables and Connectors Pod and Logic Cable Pin Assignments Power Switch/Connector Assembly Power Supply Fuse Replacement Freescale Semiconductor, Inc Power Supply Fuse Replacement MMDS0508 Target Interface Mmds Target Component General ConfigurationMMDS0508 Interfacing Your System and the Target Definitions, Acronyms and Abbreviations Hardware connection Loading the MMDS0508 Target Loading MotoSIL Target Communication Configuration MotoSIL Communication Configuration Communication Device Specification MMDS0508 Menu Entries Debugger Status Bar forData Format Communication Communication Baud Rate Maximum Baud Rate Memory ConfigurationShow Protocol 0nnnnVxx.MEM Personality .MEM Files 12 Error Message Dual-Port RAM Signals EmulationMemory Bus Tracing ResetMCU Clock Motorola ESL Parameters Default Target SetupComdev Introduction to the Bus Analyzer Bus AnalyzerBaudrate Showprot Watchpoints Using the Bus AnalyzerTrace Modes Trace Buffer 15 Bus Analyzer Trace window popup menu 17 Bus Analyzer Trigger Setup Trigger Setup Sequencer Setup Continuous All Cycles Non-Triggered Modes Counted Modes Triggered Modes/Sequential Event Mode Counted/Sequential Recording Mode Clock Frequency Time Tag Clock Setup Collecting Data Recording Bus Data Viewing Collected DataTrigger Event View Cycles Events Textual Display Instructions Only Display Control SignalsTime Tag Time Measuring Zoom In or Out Graphical Display 22 Trace Zoom Display Add / Remove Items in the Trace Window ShowLocation Search for a Frame Scrolling the Display OK Button Search for EventsForward Backward Previous Event Search for a Pattern Next Pattern Cancel ButtonPrevious Pattern Dump File Dumping the Bus analyzer data to a file 31 Analyzer Dump Only Frame Baud Rate Command Mmds CommandsShort Description Syntax Trigger Commands Set trigger Data RED ORG YEL GRN Examples Disables triggers a and B Bus Analyzer Commands Darm GP B Log trace Open the logging file Sets the 8 Mhz oscillator as the time tag clock source Address SP 8 Set sequencer Display time tag difference VA MODE=MIX INS Graph Reset Commands Target Signal Emulation Commands Other Commands MEM OSC Protocol Disables the real time memory block Index IDX-84 MMDS0508 Target Interface IDX-85 IDX-86