Debugger Status Bar for | Freescale Semiconductor MMDS0508 guide

		Freescale Semiconductor, Inc.
		MMDS Target Component
		4.7 The Debugger Status Bar for the MMDS


	NOTE	Saving the communication device and the baud rate through this
		dialog box overrides environment variables BAUDRATE and
		COMDEV of the default.env file.

4.6.2 Data Format

The MMDS0508 data format is 8 data bits, 1 stop bit, no parity, and a variable baud rate. The default speed is 9600 baud, unless you change this default via the menu selection MMDS0508>Communication....

Communication speeds of 1200 through 115200 baud are available, depending on the host-computer hardware.

4.7The Debugger Status Bar for the

MMDS

Once you have loaded the MMDS Target Component, the debugger status bar gives specific information as shown in Figure 4.8:

Figure 4.8 The Debugger Status Bar

From left to right, this information is: the serial-communication baud rate, the debugger running mode, the BUS analyzer mode, the MCU name (depending on the MCU-Id), and the debugger status.

4.8 MMDS0508 Menu Entries

The Figure 4.9 show the MMDS0508 Menu Entries:

MMDS0508 Target Interface

4–29

For More Information: www.freescale.com

Image 29

Freescale Semiconductor manual Debugger Status Bar for, MMDS0508 Menu Entries, Data Format

Contents

Freescale Semiconductor, Inc MMDS0508 Target Interface How to Contact Metrowerks Table of Contents Appendix Introduction Mmds Features System Components Freescale Semiconductor, Inc System Components MMDS0508 Target Interface Installation M68MMDS0508 Station Module Right Side Factory Test Header J1 Configuring the Platform Board Factory Test Header J1 Port Voltage Control Headers J2-J4 Removing the EM Installing the EM Bus State Analyzer Connection Making Cable ConnectionsHost Computer Connection Target Cable Connection Power Connection Making Cable Connections MMDS0508 Target Interface RS232 Serial Connector Reset Switch Serial Connector and Cable Pin Assignments Logic Cables and Connectors Pod and Logic Cable Pin Assignments Power Switch/Connector Assembly Power Supply Fuse Replacement Freescale Semiconductor, Inc Power Supply Fuse Replacement MMDS0508 Target Interface Mmds Target Component MMDS0508 ConfigurationGeneral Interfacing Your System and the Target Definitions, Acronyms and Abbreviations Hardware connection Loading the MMDS0508 Target Loading MotoSIL Target Communication Configuration MotoSIL Communication Configuration Communication Device Specification Data Format Debugger Status Bar forMMDS0508 Menu Entries Communication Communication Baud Rate Show Protocol Memory ConfigurationMaximum Baud Rate 0nnnnVxx.MEM Personality .MEM Files 12 Error Message Memory Signals EmulationDual-Port RAM MCU Clock ResetBus Tracing Comdev Default Target SetupMotorola ESL Parameters Introduction to the Bus Analyzer Bus AnalyzerBaudrate Showprot Watchpoints Using the Bus AnalyzerTrace Modes Trace Buffer 15 Bus Analyzer Trace window popup menu 17 Bus Analyzer Trigger Setup Trigger Setup Sequencer Setup Continuous All Cycles Non-Triggered Modes Counted Modes Triggered Modes/Sequential Event Mode Counted/Sequential Recording Mode Clock Frequency Time Tag Clock Setup Collecting Data Recording Bus Data Viewing Collected DataTrigger Event View Cycles Events Textual Display Instructions Only Display Control SignalsTime Tag Time Measuring Zoom In or Out Graphical Display 22 Trace Zoom Display Add / Remove Items in the Trace Window ShowLocation Search for a Frame Scrolling the Display OK Button Search for EventsForward Backward Previous Event Search for a Pattern Previous Pattern Cancel ButtonNext Pattern Dump File Dumping the Bus analyzer data to a file 31 Analyzer Dump Only Frame Baud Rate Command Mmds CommandsShort Description Syntax Trigger Commands Set trigger Data RED ORG YEL GRN Examples Disables triggers a and B Bus Analyzer Commands Darm GP B Log trace Open the logging file Sets the 8 Mhz oscillator as the time tag clock source Address SP 8 Set sequencer Display time tag difference VA MODE=MIX INS Graph Reset Commands Target Signal Emulation Commands Other Commands MEM OSC Protocol Disables the real time memory block Index IDX-84 MMDS0508 Target Interface IDX-85 IDX-86