Personality .MEM Files | Freescale Semiconductor MMDS0508 specification

Freescale Semiconductor, Inc.

MMDS Target Component

4.8 MMDS0508 Menu Entries

Figure 4.11 Memory Configuration

This dialog box shows the target’s memory setup. The system automatically loads this setup if you check the Auto select according to MCU-Idcheckbox. The debugger identifies and sets the memory map through the processor MCU-Id. To open another configuration, click the Open button. To save modifications to the current configuration, click the Save... button.

4.8.3 Personality (.MEM) Files

For proper operation, the Motosil target must load the personality file (.MEM file) that matches the connected Emulation Module (EM).

The .MEM file filename format is:

0nnnnVxx.MEM

where ‘nnnn’ is the four-digit, hexadecimal ‘MCU-Id’ number of the MCU, and ‘xx’ is a two-digit version number.

If the target cannot find this file, or if the file is not valid, the Error message box appears as shown in Figure 4.12:

4–32	MMDS0508 Target Interface

For More Information: www.freescale.com

Image 32

Freescale Semiconductor MMDS0508 manual Personality .MEM Files, 0nnnnVxx.MEM

Contents

MMDS0508 Target Interface Freescale Semiconductor, Inc How to Contact Metrowerks Table of Contents Appendix Mmds Features Introduction System Components Freescale Semiconductor, Inc System Components MMDS0508 Target Interface Installation M68MMDS0508 Station Module Right Side Configuring the Platform Board Factory Test Header J1 Port Voltage Control Headers J2-J4 Factory Test Header J1 Installing the EM Removing the EM Bus State Analyzer Connection Making Cable ConnectionsHost Computer Connection Power Connection Target Cable Connection Making Cable Connections MMDS0508 Target Interface Reset Switch RS232 Serial Connector Logic Cables and Connectors Serial Connector and Cable Pin Assignments Pod and Logic Cable Pin Assignments Power Supply Fuse Replacement Power Switch/Connector Assembly Freescale Semiconductor, Inc Power Supply Fuse Replacement MMDS0508 Target Interface Mmds Target Component MMDS0508 ConfigurationGeneral Definitions, Acronyms and Abbreviations Interfacing Your System and the Target Loading the MMDS0508 Target Hardware connection Communication Configuration Loading MotoSIL Target Communication Device Specification MotoSIL Communication Configuration Data Format Debugger Status Bar forMMDS0508 Menu Entries Communication Baud Rate Communication Show Protocol Memory ConfigurationMaximum Baud Rate Personality .MEM Files 0nnnnVxx.MEM 12 Error Message Memory Signals EmulationDual-Port RAM MCU Clock ResetBus Tracing Comdev Default Target SetupMotorola ESL Parameters Bus Analyzer Introduction to the Bus AnalyzerBaudrate Showprot Using the Bus Analyzer WatchpointsTrace Modes Trace Buffer Trace window popup menu 15 Bus Analyzer Trigger Setup 17 Bus Analyzer Trigger Setup Sequencer Setup Non-Triggered Modes Continuous All Cycles Triggered Modes/Sequential Event Mode Counted Modes Counted/Sequential Recording Mode Time Tag Clock Setup Clock Frequency Collecting Data Viewing Collected Data Recording Bus DataTrigger Event View Cycles Textual Display Events Control Signals Instructions Only DisplayTime Tag Time Measuring Graphical Display Zoom In or Out 22 Trace Zoom Display ShowLocation Add / Remove Items in the Trace Window Scrolling the Display Search for a Frame Search for Events OK ButtonForward Backward Search for a Pattern Previous Event Previous Pattern Cancel ButtonNext Pattern Dumping the Bus analyzer data to a file Dump File 31 Analyzer Dump Only Frame Mmds Commands Baud Rate CommandShort Description Syntax Trigger Commands Set trigger Data RED ORG YEL GRN Examples Disables triggers a and B Bus Analyzer Commands Darm GP B Log trace Open the logging file Sets the 8 Mhz oscillator as the time tag clock source Address SP 8 Set sequencer Display time tag difference VA MODE=MIX INS Graph Target Signal Emulation Commands Reset Commands Other Commands MEM OSC Protocol Disables the real time memory block Index IDX-84 MMDS0508 Target Interface IDX-85 IDX-86