Freescale Semiconductor MMDS0508 4.9 Default Target Setup

MMDS Target Component

4.9 Default Target Setup

4–36 MMDS0508 Target Interface

4.9 Default Target Setup

As with any target, you can use the Target menu to load the MMDS target component,

or you can set the MMDS target component as a default in the PROJECT.INI file.

This file should be in the project directory.

Example of PROJECT.INI file.

[DEFAULTS]

Window0=Source 0 0 50 40

Window1=Assembly 50 0 50 40

Window2=Register 50 40 50 30

Window3=Memory 50 70 50 30

Window4=Data 0 40 50 25

Window5=Command 0 65 50 20

Window6=Module 0 85 50 15

Target=Motosil

[Motorola ESL]

COMDEV=COM2

BAUDRATE=57600

SHOWPROT=1

NOTE For more information about the PROJECT.INI file, please see the

debugger manual.

4.9.1 Motorola ESL Parameters

In normal use, you set these parameters in the project.ini file once, interactively,

during installation. You use these parameter values in subsequent debugging sessions.

4.9.1.1 COMDEV

This parameter specifies the host-computer communication port. COM1 is the default

communication device for PCs. The default for UNIX systems is /dev/ttya.

Freescale Semiconductor, Inc.

For More Information: www.freescale.com

Contents

Main How to Contact Metrowerks Table of Contents 1 General Description 5 2Installation 9 3 Connector Information 17 4 MMDS Target Component 23 A Appendix 59 General Description 1.1 Introduction 1.2 MMDS Features 1.3 System Components Page Page Installation Installation 2.1 Introduction Page 2.2 Configuring the Platform Board 2.2.1 Factory Test Header (J1) 2.2.2 Port Voltage Control Headers (J2J4) 2.3 Installing the EM 2.4 Removing the EM 2.5 Making Cable Connections 2.5.1 Host Computer Connection 2.5.2 Bus State Analyzer Connection 2.5.3 Target Cable Connection 2.5.4 Power Connection Page Connector Information 3.1 Introduction 3.2 Reset Switch 3.3 RS232 Serial Connector 3.4 Logic Cables and Connectors Page 3.5 Power Supply Fuse Replacement Page Page MMDS Target Component 4.1 Introduction 4.2 General 4.2.1 MMDS0508 4.2.2 Configuration 4.3 Definitions, Acronyms and Abbreviations 4.4 Interfacing Your System and the Target 4.5 Loading the MMDS0508 Target 4.6 Communication Configuration 4.6.1 Communication Device Specification 4.6.2 Data Format 4.7 The Debugger Status Bar for the MMDS 4.8 MMDS0508 Menu Entries 4.8.1 Communication Baud Rate 4.8.1.1 Communication 4.8.1.2 Maximum Baud Rate 4.8.1.3 Show Protocol 4.8.2 Memory Configuration 4.8.3 Personality (.MEM) Files Page 4.8.3.1 Dual-Port RAM 4.8.3.2 Memory 4.8.4 Signals Emulation 4.8.4.1 MCU Clock 4.8.4.2 Reset 4.8.5 Bus Tracing 4.9 Default Target Setup 4.9.1 Motorola ESL Parameters 4.9.1.1 COMDEV 4.9.1.2 BAUDRATE 1200, 2400, 4800, 9600, 19200, 28800, 38400, 57600, 115200. 4.10 Bus Analyzer 4.10.1 Introduction to the Bus Analyzer 4.10.1.1 Watchpoints 4.10.1.2 Trace Modes 4.10.1.3 Trace Buffer 4.10.2 Using the Bus Analyzer 4.10.2.1 The Trace window popup menu 4.10.2.2 Trigger Setup 4.10.2.3 Sequencer Setup 4.10.2.4 Non-Triggered Modes 4.10.2.5 Counted Modes 4.10.2.6 Triggered Modes/Sequential Event Mode 4.10.2.7 Counted/Sequential Recording Mode 4.10.2.8 Time Tag Clock Setup 4.10.3 Collecting Data 4.10.3.7 Recording Bus Data 4.10.3.8 Trigger Event 4.10.4 Viewing Collected Data 4.10.4.1 View Cycles 4.10.4.2 Textual, Graphical or Instructions 4.10.4.3 Textual Display 4.10.4.4 Instructions Only Display 4.10.4.5 Graphical Display Page Page 4.10.5 Scrolling the Display 4.10.5.1 Search for a Frame 4.10.5.2 Search for Events 4.10.5.3 Search for a Pattern Page 4.10.6 Dumping the Bus analyzer data to a file 4.10.6.1 Dump File Page A Appendix A.1 MMDS Commands A.1.1 Baud Rate Command BAUD A.1.1.1 Short Description A.1.2 Trigger Commands CT A.1.2.1 Short Description A.1.2.2 Syntax A.1.2.3 Description ST A.1.2.4 Short Description A.1.2.5 Syntax A.1.2.6 Description Page Page TD A.1.2.7 Short Description A.1.2.8 Syntax A.1.2.9 Description TE A.1.2.10 Short Description A.1.2.11 Syntax A.1.2.12 Description A.1.3 Bus Analyzer Commands Page Page A.1.3.15 Description LT A.1.3.16 Short Description A.1.3.17 Syntax A.1.3.18 Description SC A.1.3.19 Short Description A.1.3.20 Syntax A.1.3.21 Description SP A.1.3.22 Short Description A.1.3.23 Description A.1.3.24 Syntax Page Page SQ A.1.3.25 Short Description A.1.3.26 Syntax A.1.3.27 Description TT A.1.3.28 Short Description A.1.3.29 Syntax A.1.3.30 Description VA A.1.3.31 Short Description A.1.3.32 Syntax A.1.3.33 Description A.1.4 Target Signal Emulation Commands A.1.5 Reset Commands A.1.6 Other Commands A.1.6.3 Description MEM A.1.6.4 Short Description A.1.6.5 Syntax A.1.6.6 Description OSC A.1.6.7 Short Description A.1.6.8 Syntax A.1.6.9 Description Page A.1.6.15 Description Index Symbols A B C M N O P R T V W Z