Freescale Semiconductor MMDS0508 4.10.4.3 Textual Display

MMDS Target Component

4.10 Bus Analyzer

4–48 MMDS0508 Target Interface

The analyzer can display its contents as text or as a graphic. You can have a textual

display of all frames, or a textual display of only instruction-start frames. Additionally,

you can choose the Trace>Items... menu selection to specify items for display.

4.10.4.3 Textual Display

If you choose the Textual format, the software displays all the frames of the trace

buffer contents, in a textual form, as shown in Figure 4.20. Use the vertical scroll bar

to scroll to other frames. Use the horizontal scroll bar to scroll to other signals.

Each display line gives the data of one frame: text below explains these data items.

You can add or remove data items. (Please see the section Adding / Removing Items in

the Trace Window.) The marker consists of two horizontal lines, which facilitate

reading the data items for a specific frame; the analyzer highlights the number of the

marked frame.

Figure 4.20 Trace Textual Format Display

Frame This column lists the cycle (or frame) number of each frame : identifying

integers, from 1 to 8191. The most recently stored frame has number 8191 (or the

highest number all the frames stored).

4.10.4.3.1 Events

This column lists identifiers of matching events. That is, if frame data matches any

event data definitions, the analyzer displays the event identifiers (A, B, C, or D) in this

column.

Freescale Semiconductor, Inc.

For More Information: www.freescale.com

Contents

Main How to Contact Metrowerks Table of Contents 1 General Description 5 2Installation 9 3 Connector Information 17 4 MMDS Target Component 23 A Appendix 59 General Description 1.1 Introduction 1.2 MMDS Features 1.3 System Components Page Page Installation Installation 2.1 Introduction Page 2.2 Configuring the Platform Board 2.2.1 Factory Test Header (J1) 2.2.2 Port Voltage Control Headers (J2J4) 2.3 Installing the EM 2.4 Removing the EM 2.5 Making Cable Connections 2.5.1 Host Computer Connection 2.5.2 Bus State Analyzer Connection 2.5.3 Target Cable Connection 2.5.4 Power Connection Page Connector Information 3.1 Introduction 3.2 Reset Switch 3.3 RS232 Serial Connector 3.4 Logic Cables and Connectors Page 3.5 Power Supply Fuse Replacement Page Page MMDS Target Component 4.1 Introduction 4.2 General 4.2.1 MMDS0508 4.2.2 Configuration 4.3 Definitions, Acronyms and Abbreviations 4.4 Interfacing Your System and the Target 4.5 Loading the MMDS0508 Target 4.6 Communication Configuration 4.6.1 Communication Device Specification 4.6.2 Data Format 4.7 The Debugger Status Bar for the MMDS 4.8 MMDS0508 Menu Entries 4.8.1 Communication Baud Rate 4.8.1.1 Communication 4.8.1.2 Maximum Baud Rate 4.8.1.3 Show Protocol 4.8.2 Memory Configuration 4.8.3 Personality (.MEM) Files Page 4.8.3.1 Dual-Port RAM 4.8.3.2 Memory 4.8.4 Signals Emulation 4.8.4.1 MCU Clock 4.8.4.2 Reset 4.8.5 Bus Tracing 4.9 Default Target Setup 4.9.1 Motorola ESL Parameters 4.9.1.1 COMDEV 4.9.1.2 BAUDRATE 1200, 2400, 4800, 9600, 19200, 28800, 38400, 57600, 115200. 4.10 Bus Analyzer 4.10.1 Introduction to the Bus Analyzer 4.10.1.1 Watchpoints 4.10.1.2 Trace Modes 4.10.1.3 Trace Buffer 4.10.2 Using the Bus Analyzer 4.10.2.1 The Trace window popup menu 4.10.2.2 Trigger Setup 4.10.2.3 Sequencer Setup 4.10.2.4 Non-Triggered Modes 4.10.2.5 Counted Modes 4.10.2.6 Triggered Modes/Sequential Event Mode 4.10.2.7 Counted/Sequential Recording Mode 4.10.2.8 Time Tag Clock Setup 4.10.3 Collecting Data 4.10.3.7 Recording Bus Data 4.10.3.8 Trigger Event 4.10.4 Viewing Collected Data 4.10.4.1 View Cycles 4.10.4.2 Textual, Graphical or Instructions 4.10.4.3 Textual Display 4.10.4.4 Instructions Only Display 4.10.4.5 Graphical Display Page Page 4.10.5 Scrolling the Display 4.10.5.1 Search for a Frame 4.10.5.2 Search for Events 4.10.5.3 Search for a Pattern Page 4.10.6 Dumping the Bus analyzer data to a file 4.10.6.1 Dump File Page A Appendix A.1 MMDS Commands A.1.1 Baud Rate Command BAUD A.1.1.1 Short Description A.1.2 Trigger Commands CT A.1.2.1 Short Description A.1.2.2 Syntax A.1.2.3 Description ST A.1.2.4 Short Description A.1.2.5 Syntax A.1.2.6 Description Page Page TD A.1.2.7 Short Description A.1.2.8 Syntax A.1.2.9 Description TE A.1.2.10 Short Description A.1.2.11 Syntax A.1.2.12 Description A.1.3 Bus Analyzer Commands Page Page A.1.3.15 Description LT A.1.3.16 Short Description A.1.3.17 Syntax A.1.3.18 Description SC A.1.3.19 Short Description A.1.3.20 Syntax A.1.3.21 Description SP A.1.3.22 Short Description A.1.3.23 Description A.1.3.24 Syntax Page Page SQ A.1.3.25 Short Description A.1.3.26 Syntax A.1.3.27 Description TT A.1.3.28 Short Description A.1.3.29 Syntax A.1.3.30 Description VA A.1.3.31 Short Description A.1.3.32 Syntax A.1.3.33 Description A.1.4 Target Signal Emulation Commands A.1.5 Reset Commands A.1.6 Other Commands A.1.6.3 Description MEM A.1.6.4 Short Description A.1.6.5 Syntax A.1.6.6 Description OSC A.1.6.7 Short Description A.1.6.8 Syntax A.1.6.9 Description Page A.1.6.15 Description Index Symbols A B C M N O P R T V W Z