Osc | Freescale Semiconductor MMDS0508 manual

Freescale Semiconductor, Inc.

Appendix

MMDS Commands

ROM	3E00..FDFF	ROM
IO	FE00..FE1F	PRU or TOP	TOP board resource or the PRU
NONE	FE20..FFDB	NONE
ROM	FFDC..FFFE	ROM
COP	FFFF..FFFF	special ram for cop
RT MEM	0.. 3FF	(disabled)

-------------------------------------------------------

OSC

A.1.6.7 Short Description

selects Emulator Clock Frequency command.

A.1.6.8 Syntax

OSC [rate source]

A.1.6.9 Description

The OSC command selects the emulator clock frequency: one of five internally generated frequencies (16 Mhz, 8 Mhz, 4 Mhz, 2 Mhz, or 1 Mhz), or an external clock source. The firmware sets the default emulator clock rate, adapting it to the current frequency.

Entering this command without parameters opens the corresponding dialog box.

OSC [rate source]

where rate is: OSC1MHZ	Selects the 1 Mhz oscillator.
OSC2MHZ	Selects the 2 Mhz oscillator.
OSC4MHZ	Selects the 4 Mhz oscillator.
OSC8MHZ	Selects the 8 Mhz oscillator.

	OSC16MHZ Selects the 16 Mhz oscillator.
	Where source is: EXT	Selects an external clock source.

A–80	MMDS0508 Target Interface

For More Information: www.freescale.com

Image 80

Freescale Semiconductor MMDS0508 manual Osc

Contents

MMDS0508 Target Interface Freescale Semiconductor, Inc How to Contact Metrowerks Table of Contents Appendix Mmds Features Introduction System Components Freescale Semiconductor, Inc System Components MMDS0508 Target Interface Installation M68MMDS0508 Station Module Right Side Configuring the Platform Board Factory Test Header J1 Port Voltage Control Headers J2-J4 Factory Test Header J1 Installing the EM Removing the EM Bus State Analyzer Connection Making Cable ConnectionsHost Computer Connection Power Connection Target Cable Connection Making Cable Connections MMDS0508 Target Interface Reset Switch RS232 Serial Connector Logic Cables and Connectors Serial Connector and Cable Pin Assignments Pod and Logic Cable Pin Assignments Power Supply Fuse Replacement Power Switch/Connector Assembly Freescale Semiconductor, Inc Power Supply Fuse Replacement MMDS0508 Target Interface Mmds Target Component MMDS0508 ConfigurationGeneral Definitions, Acronyms and Abbreviations Interfacing Your System and the Target Loading the MMDS0508 Target Hardware connection Communication Configuration Loading MotoSIL Target Communication Device Specification MotoSIL Communication Configuration Data Format Debugger Status Bar forMMDS0508 Menu Entries Communication Baud Rate Communication Show Protocol Memory ConfigurationMaximum Baud Rate Personality .MEM Files 0nnnnVxx.MEM 12 Error Message Memory Signals EmulationDual-Port RAM MCU Clock ResetBus Tracing Comdev Default Target SetupMotorola ESL Parameters Bus Analyzer Introduction to the Bus AnalyzerBaudrate Showprot Using the Bus Analyzer WatchpointsTrace Modes Trace Buffer Trace window popup menu 15 Bus Analyzer Trigger Setup 17 Bus Analyzer Trigger Setup Sequencer Setup Non-Triggered Modes Continuous All Cycles Triggered Modes/Sequential Event Mode Counted Modes Counted/Sequential Recording Mode Time Tag Clock Setup Clock Frequency Collecting Data Viewing Collected Data Recording Bus DataTrigger Event View Cycles Textual Display Events Control Signals Instructions Only DisplayTime Tag Time Measuring Graphical Display Zoom In or Out 22 Trace Zoom Display ShowLocation Add / Remove Items in the Trace Window Scrolling the Display Search for a Frame Search for Events OK ButtonForward Backward Search for a Pattern Previous Event Previous Pattern Cancel ButtonNext Pattern Dumping the Bus analyzer data to a file Dump File 31 Analyzer Dump Only Frame Mmds Commands Baud Rate CommandShort Description Syntax Trigger Commands Set trigger Data RED ORG YEL GRN Examples Disables triggers a and B Bus Analyzer Commands Darm GP B Log trace Open the logging file Sets the 8 Mhz oscillator as the time tag clock source Address SP 8 Set sequencer Display time tag difference VA MODE=MIX INS Graph Target Signal Emulation Commands Reset Commands Other Commands MEM OSC Protocol Disables the real time memory block Index IDX-84 MMDS0508 Target Interface IDX-85 IDX-86