Manuals / Brands / Computer Equipment / Network Card / Fujitsu Siemens Computers / Computer Equipment / Network Card

Fujitsu Siemens Computers Point 1600, Point 500 Figure 2-4. Port Replicator (Back View)

1 52

Download 52 pages, 499.61 Kb

Assembling the Port Replicator

2-5

replicator on the desk stand in one of three orientations: one landscape-mode and two portrait-mode

positions.

Figure 2-4. Port Replicator (Back View)

To install the wi re catch,

1. Determine which set of mounting holes is appropriate depending on how you intend to orient the

pen tablet on the desk stand. Figure 2-4 shows the wire catch installed in the landscape-mode

position. The mounting holes for both portrait-mode positions are also called out.

2. Insert one end of the wire catch into the round hole.

3. Insert the opposi te end of the wire catch into the co rresponding slotted hol e. To do so, push the end

of the wire catch inward until it can be inserted into the hole.

Note: Ensure that the wire catch is not installed backwards. When installed correctly, the wire catch hooks over

the top of the desk stand.

Connectors 2

Figure 2-5 shows the location of connectors o n the port replicator. Note that the ability of the pen tablet to

utilize these connectors is determined by BIOS settings. Ensure that the ports you intend to use are

enabled and properly configured in the BIOS.

Feet Feet

Wire Catch

Attach wire catch

here for portrait

orientation (right

side up).

Attach wire catch

here for portrait

orientation (left

side up).

Contents

Main Page Page Page Agency Compliance FCC Notice Canadian DOC Compliance Page Tabl e of Contents Page About This Guide Organization 0 Page Chapter 1 Introduction to Connectivity Peripherals Table 1-1. Connectivity Peripheral Model Numbers Page Cradle Module 1 The Portable Port Expander 1 Port Replicator 1 High-Usage C radle 1 High-Connectivity Cradle 1 Wall-Mount Cradle 1 Charge-Only Cradle 1 Chapter 2 Assembling and Installing Connectivity Peripherals Portable Port Expander 2 Figure 2-1. Portable Port Expander Latch Removing the Latch and Spacer (For In stallation in Cradle Module Onl y) 2 Latch Detail: Figure 2-2. Bottom View, Portable Port Expander Peripheral connectors on the portable port expander are described in Table 2-1. Table 2-1. Portable Port Expander Connectors Assemblin g th e Port Replicator 2 Figure 2-3. Installing the Portable Port Exp an der Attaching the Feet 2 Attaching the Wire Catch 2 Figure 2-4. Port Replicator (Back View) Figure 2-5. Bottom View, Port Replicator Connectors on the port replicator are described in Table 2-2. Table 2-2. Port Replicator Connectors Using the Folding Desk Stand 2 Figure 2-6. Folding Desk Stand Assemblin g th e H i gh - U s age C radle 2 Figure 2-7. High-Usage Cradle Assembly Figure 2-8. High-Usage Cradle Bottom View Table 2-3. High-Usage Cradle Connectors Installing the High-Usage Cradle 2 Figure 2-9. Fastening Cradle Module to Desktop Assembling the High-Connectivity Cradle 2 Figure 2-10. High-Connectivity Cradle Assembly Assembling the High-Connectivity Cradle 2-15 Figure 2-11. High-Connectivity Cradle Bottom View Installing the High-Connectivity Cradle 2 Table 2-4. High-Connectivity Cradle Connectors Installing the Wall-Mount Cradle 2 Required Tools and Hardware 2 Page Figure 2-12. Wall-Mount Cradle Mounting Plate Figure 2-13. Coiling DC Suppl y Cable Figure 2-14. Installing an FMWKB3 Keyboard Figure 2-15. Wall-Mount Cradle Exploded View Figure 2-16. Attaching Keyboard Tray Assembly to Mounting Plate (Right Side) Page Page Figure 2-21. Checking Cradle Module Alignment Testing the Wall-Mount Cradle After Installation 2 Figure 2-22. Wall-Mount Cradle Closed Position Installing the Wall-Mount Cradle Connectors on the wall-mount cradle are described in Table 2 -5. Table 2-5. Wall-Mount Cradle Connectors Installing the Charge-Only Cradle 2 Figure 2-23. Charge-Only Cradle Confirming External Power Is Supplied 2 Figure 2-24. Status Lights on the Pen Tablet MIC Page Index C H K M