Manuals / Brands / Computer Equipment / Network Card / Fujitsu Siemens Computers / Computer Equipment / Network Card

Fujitsu Siemens Computers Point 1600, Point 500 Figure 2-7. High-Usage Cradle Assembly

1 52

Download 52 pages, 499.61 Kb

Assembling the High-Usage Cradle

2-9

Figure 2-7. High-Usage Cradle Assembly

3. Determine which side the adjustmen t knob will be installed on. The knob can be installed on either

the right or left side of the cradle module to accommodate right- or left-handed users.

4. Install the #10 screw, lock washer, and nylon washer provided on one side (opposite the side where

the knob will be installed) to fasten the cradle module to the cradle base. (Do not tighten the screw at

this step.) Ensure th at the nylon washer is ins talled closest to the cra dle base as shown in Figu re 2-7.

5. Install the knob and spacer on the desired side of the cradle. (Do not tighten the knob in this step.)

6. Tighten the screw (that you installed in step 4) to 1/2 turn past finger tight and install the cover over

the head of the screw as shown in Figure 2-7. To do so, remove the protective backing and apply the

adhesive side of the cover toward the cradle.

7. Install the cover label inside the cradle module as shown in Figure 2-7. To do so, remove the

protective backing and apply the adhesive side of the label toward the cradle module. (This covers

access holes in the cradle module that are not used in this assembly.)

Cradle

Module

Cradle

Base

Cover

Screw

Nylon Washer

Spacer

Adjustment

Cover Label

Kensington Security Standard Slot Knob

Star Washer

Contents

Main Page Page Page Agency Compliance FCC Notice Canadian DOC Compliance Page Tabl e of Contents Page About This Guide Organization 0 Page Chapter 1 Introduction to Connectivity Peripherals Table 1-1. Connectivity Peripheral Model Numbers Page Cradle Module 1 The Portable Port Expander 1 Port Replicator 1 High-Usage C radle 1 High-Connectivity Cradle 1 Wall-Mount Cradle 1 Charge-Only Cradle 1 Chapter 2 Assembling and Installing Connectivity Peripherals Portable Port Expander 2 Figure 2-1. Portable Port Expander Latch Removing the Latch and Spacer (For In stallation in Cradle Module Onl y) 2 Latch Detail: Figure 2-2. Bottom View, Portable Port Expander Peripheral connectors on the portable port expander are described in Table 2-1. Table 2-1. Portable Port Expander Connectors Assemblin g th e Port Replicator 2 Figure 2-3. Installing the Portable Port Exp an der Attaching the Feet 2 Attaching the Wire Catch 2 Figure 2-4. Port Replicator (Back View) Figure 2-5. Bottom View, Port Replicator Connectors on the port replicator are described in Table 2-2. Table 2-2. Port Replicator Connectors Using the Folding Desk Stand 2 Figure 2-6. Folding Desk Stand Assemblin g th e H i gh - U s age C radle 2 Figure 2-7. High-Usage Cradle Assembly Figure 2-8. High-Usage Cradle Bottom View Table 2-3. High-Usage Cradle Connectors Installing the High-Usage Cradle 2 Figure 2-9. Fastening Cradle Module to Desktop Assembling the High-Connectivity Cradle 2 Figure 2-10. High-Connectivity Cradle Assembly Assembling the High-Connectivity Cradle 2-15 Figure 2-11. High-Connectivity Cradle Bottom View Installing the High-Connectivity Cradle 2 Table 2-4. High-Connectivity Cradle Connectors Installing the Wall-Mount Cradle 2 Required Tools and Hardware 2 Page Figure 2-12. Wall-Mount Cradle Mounting Plate Figure 2-13. Coiling DC Suppl y Cable Figure 2-14. Installing an FMWKB3 Keyboard Figure 2-15. Wall-Mount Cradle Exploded View Figure 2-16. Attaching Keyboard Tray Assembly to Mounting Plate (Right Side) Page Page Figure 2-21. Checking Cradle Module Alignment Testing the Wall-Mount Cradle After Installation 2 Figure 2-22. Wall-Mount Cradle Closed Position Installing the Wall-Mount Cradle Connectors on the wall-mount cradle are described in Table 2 -5. Table 2-5. Wall-Mount Cradle Connectors Installing the Charge-Only Cradle 2 Figure 2-23. Charge-Only Cradle Confirming External Power Is Supplied 2 Figure 2-24. Status Lights on the Pen Tablet MIC Page Index C H K M