Replace Display Battery | Graco 313289s instruction

Repair

Replace Display Battery

Do not replace battery when an explosive gas atmo- sphere may be present.

NOTICE

To avoid damaging circuit board, wear a grounding strap.

1.Perform steps 1-4 under Upgrade Software sec- tion, page 35.

2.Use a flat head screwdriver to pry out old battery.

Remove Old Battery

Connector

Insert New Battery									Tabs
									Tabs



					r_xm1a00_312359_313289_9_8a

3.Replace with new battery. Ensure battery fits under connector tabs before snapping other end in place.

NOTE:

Use only Panasonic CR2032 batteries for replacement.

4.Reassemble access cover (204e) and screws (204f).

Replace Display

NOTE: Order kit 257484 for replacement.

NOTICE

To avoid damaging circuit board, wear a grounding strap.

1.Remove shroud. See Remove Shroud.

2.Disconnect power.

3.Remove four nuts (4); leave two nuts on left side of panel tight. Open front panel of control box (11).

4.Disconnect CAN cable from display module.

5.Remove four screws (204b) from rear display panel (204c) while holding front display panel (204d) in place.

NOTE:

To ease removal process use clear tape to hold front display panel (204d) in place.

204d								24a
								24a
								312359 313289
								r_
								r_

204c

204b

6.Remove rear display panel (204c) and disconnect display cable and key switch cable (239) from circuit board.

36

313289S

Image 36

Graco 313289s important safety instructions Replace Display Battery

Contents

XM Plural-Component Sprayers313289S Contents Related Manuals Component Manuals in U.S. EnglishManual Description Fire and Explosion Hazard Intrinsic Safety Equipment Misuse Hazard Models Location Category Key Approvals XM a XM B XM D XM C XM E Overview Isocyanate HazardMaterial Self-Ignition Moisture Sensitivity Isocyanates Components a and B Changing MaterialsKeep Components a and B Separate Lift Using a Forklift Lift Using a HoistBefore Repair Location Proper Lifting of Sprayer Pressure Relief Procedure Relieve a and B Fluid PressureRelieve Pump Fluid Pressure Flush Before Using Equipment Flush Flush Mixed MaterialFlush Mix Manifold Use Solvent Pump Follow Pressure Relief Procedure, Procedure Empty and Flush Entire System new sprayer or end of jobGuidelines Turn on heaters until fluid lines are clear of sol- vent R3123593132896 R3123593132897 Cleaning Procedure Relieve pressure. See Pressure Relief Procedure,Shutdown Entire System Flush Entire System new sprayer or end of job on XM Setup and Troubleshooting Guide Troubleshooting Problem Cause Solution See Appendix a in manual Tor Power Supply Control Compo Alarms View AlarmsDiagnose Alarms Clear Alarms Alarm Codes and Troubleshooting Alarm Code Alarm Problem When Active Cause Solution See Pump Assembly, Pump Test Daily Check Recommended Optional User-Settable Maintenance Warnings Optional User-Settable Spray Limits Possible Alarms by Mode Mode Control Logic AlarmsR2D Stop LED Diagnostic Information Alarm Code KeyModule Status LED Signal Diagnosis Solution What Alert Where Repair Replace Air Filter ElementMain Air Inlet Manifold Filter Both Filters User Interface/Control Box Remove ShroudReplace Solenoid Module DVA DVB Update USB Module Software Load software. See Update USB Module Soft WareReplace USB Module Update Fluid Control Module FCM Software Load software. See Update Fluid Control Module FCM SoftwareReplace Fluid Control Module FCM Replace Alarm Upgrade SoftwareDisplay Replace Display Battery Replace Display Wall Power Supply Control Components Replace Power Supply ModuleReplace Front Panel Alternator Power Supply Control Components Alternator Module RepairFCM USB Replace Alternator Regulator Air Controls Gauge 326 319 330 340 331 Fluid Control Assembly Dosing Valve AssemblyMix Manifold Assembly Temperature RTD Sensor SensorsReplace Fluid Pressure Sensor Pump Assembly Remove Pump AssemblyRemove Displacement Pump Remove Air Motor Service and Repair Solvent PumpFluid Heaters Replace Electrical Schematics Simplified Electrical Schematic, XM Sprayer with Alternator Simplified Pneumatic Schematic, XM Sprayer with Alternator Electrical Schematics 313289S Detailed Electrical Schematic, XM Sprayer with Alternator 313289S Detailed Electrical Schematic, XM Sprayer with Alternator Blue Green Simplified Electrical Schematic, XM Sprayer with Wall Power XM Plural Component Sprayer with Wall Power Simplified Pneumatic Schematic, XM Sprayer with Wall Power With Wall Power Manual Detailed Electrical Schematic, XM Sprayer with Wall Power Wiring Schematics BoxFluid Heaters Hopper Heaters Junction Box Wiring Schematics 313289S Parts XM Plural-Component SprayersXM1, XM2 XM3, XM4 XMB and XME XM5, XM6XM7, XM8 Models 113 114 120 121 122 135 137 115 Fluid Control Assembly Parts Common PartsPart Description Qty See Air Controls Module Parts, Parts Varying by Model XM1 and XM2 Models XM1 and XM2 Models XM3 and XM4 Models XM Plural-Component Sprayer Models Part Description XM3 and XM4 Models XM5 and XM6 Models Adapter XM7 and XM8 Models XM7 and XM8 Models Air Power and Electric Power Versions Control Box 255771 PartsPart Description Label Base MODULE, USB Control Box Power Supply Options Alternator Assembly Wall Power Supply Assembly Wall Power Supply Assembly Cable Connections Air Controls Module 255761 Parts AdapterRegulator Coupling Switch 25A Junction Box 256540 PartsCircuit Breaker 25A Circuit Breaker 10A Fluid Control Assembly Parts SENSOR, RTD Air Inlet Manifold 255762 Parts SwivelCAP Plug Alternator Module 255728 Parts Turbine Part Description Qty Part of Assembly Repair and Spare Parts Reference Accessories and Kits Electric Heated Hose Power Supply Kit Desiccant Dryer KitShutoff/Check Valve Kit Caster Kit Dimensions System Dimensions without Hoppers System Dimensions with Hoppers Two 20-Gallon Hoppers Side MountedTwo 20-Gallon Hoppers Rear Mounted One 20-Gallon Hopper and One 7-Gallon Hopper Two 7-Gallon Hoppers Technical Data PTFE, Uhmwpe Graco Standard Warranty Graco Information