Remove Air Motor | Graco 313289s manual

4.Use a wrench to hold the tie rod flats to keep the rods from turning. Unscrew the nuts (129) from the tie rods (128) and carefully remove the displace- ment pump (66 or 67).

128

66 or 67

129

ti8301a

5.Refer to the Xtreme Displacement Pump manual 311762 to service or repair the displacement pump.

6.Follow steps in reverse order to reinstall displace- ment pump.

Repair

Remove Air Motor

1.Follow Pressure Relief Procedure, page 12.

2.Disconnect displacement pump from air motor. See steps 2 and 3 under Remove Displacement Pump, page 44.

3.Disconnect sensor cable, air line, and ground wire from air motor.

4.Remove mounting screws (4) and washers (3) hold- ing air motor (2) to mounting bracket.

2

Bracket

3

4

r__312359_313289_32

5.Refer to NXT Air Motor manual 311238 to service or repair the air motor.

6.Follow steps in reverse order to reinstall air motor.

313289S

45

Image 45

Graco 313289s important safety instructions Remove Air Motor

Contents

XM Plural-Component Sprayers313289S Contents Related Manuals Component Manuals in U.S. EnglishManual Description Fire and Explosion Hazard Intrinsic Safety Equipment Misuse Hazard Location Category Key Models XM a XM B XM D XM C XM E Approvals Isocyanate Hazard OverviewMaterial Self-Ignition Moisture Sensitivity Isocyanates Components a and B Changing MaterialsKeep Components a and B Separate Lift Using a Hoist Lift Using a ForkliftBefore Repair Location Proper Lifting of Sprayer Pressure Relief Procedure Relieve a and B Fluid PressureRelieve Pump Fluid Pressure Flush Before Using Equipment Flush Mixed Material FlushFlush Mix Manifold Use Solvent Pump Follow Pressure Relief Procedure, Empty and Flush Entire System new sprayer or end of job ProcedureGuidelines Turn on heaters until fluid lines are clear of sol- vent R3123593132896 R3123593132897 Relieve pressure. See Pressure Relief Procedure, Cleaning ProcedureShutdown Entire System Flush Entire System new sprayer or end of job on XM Setup and Troubleshooting Guide Problem Cause Solution Troubleshooting See Appendix a in manual Tor Power Supply Control Compo View Alarms AlarmsDiagnose Alarms Clear Alarms Alarm Code Alarm Problem When Active Cause Solution Alarm Codes and Troubleshooting See Pump Assembly, Pump Test Daily Check Recommended Optional User-Settable Maintenance Warnings Optional User-Settable Spray Limits Mode Control Logic Alarms Possible Alarms by ModeR2D Stop Alarm Code Key LED Diagnostic InformationModule Status LED Signal Diagnosis Solution What Alert Where Replace Air Filter Element RepairMain Air Inlet Manifold Filter Both Filters Remove Shroud User Interface/Control BoxReplace Solenoid Module DVA DVB Update USB Module Software Load software. See Update USB Module Soft WareReplace USB Module Update Fluid Control Module FCM Software Load software. See Update Fluid Control Module FCM SoftwareReplace Fluid Control Module FCM Replace Alarm Upgrade SoftwareDisplay Replace Display Replace Display Battery Wall Power Supply Control Components Replace Power Supply ModuleReplace Front Panel Alternator Module Repair Alternator Power Supply Control ComponentsFCM USB Replace Alternator Regulator Air Controls Gauge 326 319 330 340 331 Fluid Control Assembly Dosing Valve AssemblyMix Manifold Assembly Temperature RTD Sensor SensorsReplace Fluid Pressure Sensor Pump Assembly Remove Pump AssemblyRemove Displacement Pump Remove Air Motor Solvent Pump Service and RepairFluid Heaters Replace Simplified Electrical Schematic, XM Sprayer with Alternator Electrical Schematics Electrical Schematics 313289S Simplified Pneumatic Schematic, XM Sprayer with Alternator 313289S Detailed Electrical Schematic, XM Sprayer with Alternator Blue Green Detailed Electrical Schematic, XM Sprayer with Alternator XM Plural Component Sprayer with Wall Power Simplified Electrical Schematic, XM Sprayer with Wall Power Simplified Pneumatic Schematic, XM Sprayer with Wall Power Manual With Wall Power Detailed Electrical Schematic, XM Sprayer with Wall Power Box Wiring SchematicsFluid Heaters Hopper Heaters Junction Box Wiring Schematics 313289S XM Plural-Component Sprayers PartsXM1, XM2 XM3, XM4 XMB and XME XM5, XM6XM7, XM8 Models 113 114 120 121 122 135 137 115 Common Parts Fluid Control Assembly PartsPart Description Qty See Air Controls Module Parts, XM1 and XM2 Models Parts Varying by Model XM1 and XM2 Models XM Plural-Component Sprayer Models Part Description XM3 and XM4 Models XM3 and XM4 Models XM5 and XM6 Models Adapter XM7 and XM8 Models XM7 and XM8 Models Control Box 255771 Parts Air Power and Electric Power VersionsPart Description Label MODULE, USB Base Alternator Assembly Control Box Power Supply Options Wall Power Supply Assembly Cable Connections Wall Power Supply Assembly Adapter Air Controls Module 255761 PartsRegulator Coupling Junction Box 256540 Parts Switch 25ACircuit Breaker 25A Circuit Breaker 10A SENSOR, RTD Fluid Control Assembly Parts Air Inlet Manifold 255762 Parts SwivelCAP Plug Turbine Alternator Module 255728 Parts Repair and Spare Parts Reference Part Description Qty Part of Assembly Accessories and Kits Desiccant Dryer Kit Electric Heated Hose Power Supply KitShutoff/Check Valve Kit Caster Kit System Dimensions without Hoppers Dimensions System Dimensions with Hoppers Two 20-Gallon Hoppers Side MountedTwo 20-Gallon Hoppers Rear Mounted Two 7-Gallon Hoppers One 20-Gallon Hopper and One 7-Gallon Hopper PTFE, Uhmwpe Technical Data Graco Information Graco Standard Warranty