Fire and Explosion Hazard | Graco 313289s guide

Warnings

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama- tion point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where applicable.

WARNING

FIRE AND EXPLOSION HAZARD

Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent fire and explosion:

• Use equipment only in well ventilated area.

• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop cloths (potential static arc).

• Keep work area free of debris, including solvent, rags and gasoline.

•Do not plug or unplug power cords, or turn power or light switches on or off when flammable fumes are present.

•Ground all equipment in the work area. See Grounding instructions.

•Use only grounded hoses.

•Hold gun firmly to side of grounded pail when triggering into pail.

•If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment until you identify and correct the problem.

•Keep a working fire extinguisher in the work area.

•Do not connect USB device in explosive atmospheres.

SPECIAL CONDITIONS FOR SAFE USE

•To prevent the risk of electrostatic sparking, the equipment’s non-metallic parts must be cleaned with only a damp cloth.

•Refer to the Viscon HP Heater manual for special conditions for safe use.

ELECTRIC SHOCK HAZARD

Improper grounding, setup, or usage of the system can cause electric shock.

•Turn off and disconnect power at main switch before disconnecting any cables and before servicing equipment.

•Connect only to grounded power source.

•All electrical wiring must be done by a qualified electrician and comply with all local codes and regulations.

4

313289S

Image 4

Graco 313289s important safety instructions Fire and Explosion Hazard

Contents

XM Plural-Component Sprayers313289S Contents Component Manuals in U.S. English Related ManualsManual Description Fire and Explosion Hazard Intrinsic Safety Equipment Misuse Hazard Models Location Category Key Approvals XM a XM B XM D XM C XM E Overview Isocyanate HazardMaterial Self-Ignition Moisture Sensitivity Isocyanates Changing Materials Components a and BKeep Components a and B Separate Lift Using a Forklift Lift Using a HoistBefore Repair Location Proper Lifting of Sprayer Relieve a and B Fluid Pressure Pressure Relief ProcedureRelieve Pump Fluid Pressure Flush Before Using Equipment Flush Flush Mixed MaterialFlush Mix Manifold Use Solvent Pump Follow Pressure Relief Procedure, Procedure Empty and Flush Entire System new sprayer or end of jobGuidelines Turn on heaters until fluid lines are clear of sol- vent R3123593132896 R3123593132897 Cleaning Procedure Relieve pressure. See Pressure Relief Procedure,Shutdown Entire System Flush Entire System new sprayer or end of job on XM Setup and Troubleshooting Guide Troubleshooting Problem Cause Solution See Appendix a in manual Tor Power Supply Control Compo Alarms View AlarmsDiagnose Alarms Clear Alarms Alarm Codes and Troubleshooting Alarm Code Alarm Problem When Active Cause Solution See Pump Assembly, Pump Test Daily Check Recommended Optional User-Settable Maintenance Warnings Optional User-Settable Spray Limits Possible Alarms by Mode Mode Control Logic AlarmsR2D Stop LED Diagnostic Information Alarm Code KeyModule Status LED Signal Diagnosis Solution What Alert Where Repair Replace Air Filter ElementMain Air Inlet Manifold Filter Both Filters User Interface/Control Box Remove ShroudReplace Solenoid Module DVA DVB Load software. See Update USB Module Soft Ware Update USB Module SoftwareReplace USB Module Load software. See Update Fluid Control Module FCM Software Update Fluid Control Module FCM SoftwareReplace Fluid Control Module FCM Upgrade Software Replace AlarmDisplay Replace Display Battery Replace Display Replace Power Supply Module Wall Power Supply Control ComponentsReplace Front Panel Alternator Power Supply Control Components Alternator Module RepairFCM USB Replace Alternator Regulator Air Controls Gauge 326 319 330 340 331 Dosing Valve Assembly Fluid Control AssemblyMix Manifold Assembly Sensors Temperature RTD SensorReplace Fluid Pressure Sensor Remove Pump Assembly Pump AssemblyRemove Displacement Pump Remove Air Motor Service and Repair Solvent PumpFluid Heaters Replace Electrical Schematics Simplified Electrical Schematic, XM Sprayer with Alternator Simplified Pneumatic Schematic, XM Sprayer with Alternator Electrical Schematics 313289S Detailed Electrical Schematic, XM Sprayer with Alternator 313289S Detailed Electrical Schematic, XM Sprayer with Alternator Blue Green Simplified Electrical Schematic, XM Sprayer with Wall Power XM Plural Component Sprayer with Wall Power Simplified Pneumatic Schematic, XM Sprayer with Wall Power With Wall Power Manual Detailed Electrical Schematic, XM Sprayer with Wall Power Wiring Schematics BoxFluid Heaters Hopper Heaters Junction Box Wiring Schematics 313289S Parts XM Plural-Component SprayersXM1, XM2 XM3, XM4 XM5, XM6 XMB and XMEXM7, XM8 Models 113 114 120 121 122 135 137 115 Fluid Control Assembly Parts Common PartsPart Description Qty See Air Controls Module Parts, Parts Varying by Model XM1 and XM2 Models XM1 and XM2 Models XM3 and XM4 Models XM Plural-Component Sprayer Models Part Description XM3 and XM4 Models XM5 and XM6 Models Adapter XM7 and XM8 Models XM7 and XM8 Models Air Power and Electric Power Versions Control Box 255771 PartsPart Description Label Base MODULE, USB Control Box Power Supply Options Alternator Assembly Wall Power Supply Assembly Wall Power Supply Assembly Cable Connections Air Controls Module 255761 Parts AdapterRegulator Coupling Switch 25A Junction Box 256540 PartsCircuit Breaker 25A Circuit Breaker 10A Fluid Control Assembly Parts SENSOR, RTD Swivel Air Inlet Manifold 255762 PartsCAP Plug Alternator Module 255728 Parts Turbine Part Description Qty Part of Assembly Repair and Spare Parts Reference Accessories and Kits Electric Heated Hose Power Supply Kit Desiccant Dryer KitShutoff/Check Valve Kit Caster Kit Dimensions System Dimensions without Hoppers Two 20-Gallon Hoppers Side Mounted System Dimensions with HoppersTwo 20-Gallon Hoppers Rear Mounted One 20-Gallon Hopper and One 7-Gallon Hopper Two 7-Gallon Hoppers Technical Data PTFE, Uhmwpe Graco Standard Warranty Graco Information