Sensors, Replace Fluid Pressure Sensor | Graco 313289s specs

Sensors

Replace Fluid Pressure Sensor

1.Close main air shutoff valve on air supply line and on system.

2.Relieve fluid pressure. See Pressure Relief Proce- dure, page 12.

3.Open control box cover. See User Interface/Con- trol Box, page 32.

4.Disconnect pressure sensor (507) from FCM (218).

5.Disconnect fluid pressure sensor (507) from dosing valve (501).

501

506				Cord Grip	507
506				Cord Grip

r__312359_313289_30

6.Replace with new fluid pressure sensor, and recon- nect pressure sensor to FCM.

Repair

Temperature (RTD) Sensor

1.Close main air shutoff valve on air supply line and on system.

2.Relieve fluid pressure. See Pressure Relief Proce- dure, page 12.

3.Open control box cover. See User Interface/Con- trol Box, page 32.

4.Disconnect temperature sensors (506) from FCM (218).

507

506

#6 218

#5 r_xm1a00_312359_313289_15a

5.Remove RTD (506) cable from cord grip.

6.Replace with new temperature (RTD) sensor.

7.Reassemble RTD cable (506) and cord grip.

8.Connect temperature (RTD) sensor to FCM connec- tor #5. Do not use connect #6.

9.Close control box cover.

313289S

43

Image 43

Graco 313289s important safety instructions Sensors, Replace Fluid Pressure Sensor, Temperature RTD Sensor

Contents

XM Plural-Component Sprayers313289S Contents Component Manuals in U.S. English Related ManualsManual Description Fire and Explosion Hazard Intrinsic Safety Equipment Misuse Hazard Location Category Key Models XM a XM B XM D XM C XM E Approvals Moisture Sensitivity Isocyanates OverviewIsocyanate Hazard Material Self-Ignition Changing Materials Components a and BKeep Components a and B Separate Location Proper Lifting of Sprayer Lift Using a ForkliftLift Using a Hoist Before Repair Relieve a and B Fluid Pressure Pressure Relief ProcedureRelieve Pump Fluid Pressure Flush Before Using Equipment Use Solvent Pump FlushFlush Mixed Material Flush Mix Manifold Follow Pressure Relief Procedure, Turn on heaters until fluid lines are clear of sol- vent ProcedureEmpty and Flush Entire System new sprayer or end of job Guidelines R3123593132896 R3123593132897 Flush Entire System new sprayer or end of job on Cleaning ProcedureRelieve pressure. See Pressure Relief Procedure, Shutdown Entire System XM Setup and Troubleshooting Guide Problem Cause Solution Troubleshooting See Appendix a in manual Tor Power Supply Control Compo Clear Alarms AlarmsView Alarms Diagnose Alarms Alarm Code Alarm Problem When Active Cause Solution Alarm Codes and Troubleshooting See Pump Assembly, Pump Test Daily Check Recommended Optional User-Settable Maintenance Warnings Optional User-Settable Spray Limits Stop Possible Alarms by ModeMode Control Logic Alarms R2D What Alert Where LED Diagnostic InformationAlarm Code Key Module Status LED Signal Diagnosis Solution Both Filters RepairReplace Air Filter Element Main Air Inlet Manifold Filter DVA DVB User Interface/Control BoxRemove Shroud Replace Solenoid Module Load software. See Update USB Module Soft Ware Update USB Module SoftwareReplace USB Module Load software. See Update Fluid Control Module FCM Software Update Fluid Control Module FCM SoftwareReplace Fluid Control Module FCM Upgrade Software Replace AlarmDisplay Replace Display Replace Display Battery Replace Power Supply Module Wall Power Supply Control ComponentsReplace Front Panel USB Alternator Power Supply Control ComponentsAlternator Module Repair FCM Replace Alternator Regulator Air Controls Gauge 326 319 330 340 331 Dosing Valve Assembly Fluid Control AssemblyMix Manifold Assembly Sensors Temperature RTD SensorReplace Fluid Pressure Sensor Remove Pump Assembly Pump AssemblyRemove Displacement Pump Remove Air Motor Replace Service and RepairSolvent Pump Fluid Heaters Simplified Electrical Schematic, XM Sprayer with Alternator Electrical Schematics Electrical Schematics 313289S Simplified Pneumatic Schematic, XM Sprayer with Alternator 313289S Detailed Electrical Schematic, XM Sprayer with Alternator Blue Green Detailed Electrical Schematic, XM Sprayer with Alternator XM Plural Component Sprayer with Wall Power Simplified Electrical Schematic, XM Sprayer with Wall Power Simplified Pneumatic Schematic, XM Sprayer with Wall Power Manual With Wall Power Detailed Electrical Schematic, XM Sprayer with Wall Power Heaters Wiring SchematicsBox Fluid Hopper Heaters Junction Box Wiring Schematics 313289S XM3, XM4 PartsXM Plural-Component Sprayers XM1, XM2 XM5, XM6 XMB and XMEXM7, XM8 Models 113 114 120 121 122 135 137 115 See Air Controls Module Parts, Fluid Control Assembly PartsCommon Parts Part Description Qty XM1 and XM2 Models Parts Varying by Model XM1 and XM2 Models XM Plural-Component Sprayer Models Part Description XM3 and XM4 Models XM3 and XM4 Models XM5 and XM6 Models Adapter XM7 and XM8 Models XM7 and XM8 Models Label Air Power and Electric Power VersionsControl Box 255771 Parts Part Description MODULE, USB Base Alternator Assembly Control Box Power Supply Options Wall Power Supply Assembly Cable Connections Wall Power Supply Assembly Coupling Air Controls Module 255761 PartsAdapter Regulator Circuit Breaker 10A Switch 25AJunction Box 256540 Parts Circuit Breaker 25A SENSOR, RTD Fluid Control Assembly Parts Swivel Air Inlet Manifold 255762 PartsCAP Plug Turbine Alternator Module 255728 Parts Repair and Spare Parts Reference Part Description Qty Part of Assembly Accessories and Kits Caster Kit Electric Heated Hose Power Supply KitDesiccant Dryer Kit Shutoff/Check Valve Kit System Dimensions without Hoppers Dimensions Two 20-Gallon Hoppers Side Mounted System Dimensions with HoppersTwo 20-Gallon Hoppers Rear Mounted Two 7-Gallon Hoppers One 20-Gallon Hopper and One 7-Gallon Hopper PTFE, Uhmwpe Technical Data Graco Information Graco Standard Warranty