Manuals / Grizzly / Power Tools / Lathe

Grizzly instruction manual Front saddle gib screws G0516 Lathe/Mill

Models: G0516

1 72

Download 72 pages 4.1 Kb

Page 43

Compound Gib—The gib on the compound has 3 screws that maintain tension on the slide. These screws are held in place with retaining nuts. To adjust, loosen the retaining nuts and then tighten the screws as needed. When proper tension has been detected by turning the hand crank on the compound, tighten the retaining nuts while maintaining the position of the screw with an Allen® wrench as in Figure 66.

Figure 66. Compound slide gib screws.

Saddle Gibs—There are 4 tensioning screws for both the front and rear saddle gibs. Before mak- ing adjustments to the saddle gib, ensure that the front lock lever is loose by turning it counter- clockwise. See Figures 67 & 68. It is important the screws are tightened evenly. A slight drag should be detected while turning the hand crank at the end of the lathe.

Figure 67. Front saddle gib screws.

G0516 Lathe/Mill

Figure 68. Rear saddle gib screws.

Mill/Drill Gib—There are 4 screws that tension the mill/drill gib. See Figure 69. It is important that the screws are tightened evenly. A slight drag should be detected while turning the coarse downfeed handwheel.

Not Shown

Not Shown

Figure 69. Mill/drill gib screws.

-41-

Image 43

Grizzly instruction manual Front saddle gib screws G0516 Lathe/Mill

Contents

Combination LATHE/MILL Page Table of Contents Safety Instructions For Power Tools SafetyLength Additional Safety Instructions For Lathe/Mills 110V Operation Extension Cords Circuit RequirementsTypical 110V plug and outlet GroundingCommentary IntroductionIdentification Page Unpacking SET-UPPiece Inventory Bolt Measure Hardware Recognition ChartSite Considerations Clean UpBeginning Assembly Install Support Leg To attach the mill/drill unit to the lathe body Attach Mill/Drill to LatheTo mount the mill/drill eyeshield Install BacksplashTo install the backsplash Mount Mill/Drill EyeshieldTo test run the lathe Test Run LatheTo test run the mill/drill Test Run Mill/DrillLathe components G0516 Lathe/Mill Lathe OperationsRemoving lathe chuck G0516 Lathe/Mill Removing Chuck or FaceplateInstalling Tailstock Dead Center Installing Chuck Or FaceplateTo install the tailstock dead center To remove the tailstock dead center Adjusting Tailstock Longitude PositionTo adjust the tailstock longitude position Removing Tailstock Dead CenterTo change a tool post from the compound rest Changing Tool PostsCompound Slide AdjustingTo adjust the cross slide To adjust the compound slideTo move the carriage feed manually Adjusting CarriageTo use the automatic carriage feed 100 Understanding Gear ChartsShaded boxes show the thread This is how to read the feed rate chartsEd in Figure Here is a real-world example of a gear setupAs shown on the chart On some setups, smaller gears must be Used as spacers on the adjustable shaftsChanging Gears For Carriage Feed Rate 010 feed rate setup shadedPage Fixed-shaft gear mounting positions Reverse ThreadingFixed-shaft gear mounted Position B Changing Speeds Speed change chartMill/Drill MILL/DRILL OperationsTapping draw bolt loose with hammer G0516 Lathe/Mill Changing ChucksInstalling optional collet chuck G0516 Lathe/Mill Mill table installed on cross slide G0516 Lathe/Mill Lubrication MaintenanceChecking V-Belt Check the V-belt Unplug the lathe/mill from its power sourceDate Approximate Hours Of Use Maintenance Performed About Service Service AdjustmentsGibs Front saddle gib screws G0516 Lathe/Mill To align the tailstock Aligning TailstockSee Figure Bearing Preload Date Approximate Hours Of Use Service Performed Reference Info Machine Data Sheet G0516 Lathe/Mill G0516 PS05M Phlp HD SCR M5-.8 X Page PS09M Page Page PS28M Page Page PK69M Page Gear Z72 Page PB26M G0516 Lathe/Mill G0516 Lathe/Mill PSB01M Dust Guard Warranty and Returns Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCPage #ALL 4ODAYD&ORO