Assembly | Grizzly G0601 instruction

Assembly

The Model G0442/G0601 is a heavy machine. Serious personal injury may occur if safe moving methods are not used. To be safe, get assistance and use power equip- ment to move the ship- ping crate and remove the machine from the crate.

To assemble the dust collector:

1.Connect the upper stand legs with the lower stand braces, using (16) 3⁄8"-16 x 3⁄4" hex bolts,

(32)3⁄8" flat washers, and (16) 3⁄8"-16 lock nuts (see Figure 12).

Note: Do not fully tighten the fasteners for now.

x 16

Figure 12. Initial assembly of upper stand legs

connected to lower stand braces.

-24-

2.Attach the upper stand braces to the top of the assembly from Step 1, using (16) 3⁄8"-16 x 3⁄4" hex bolts, (32) 3⁄8" flat washers, and (16) 3⁄8"-16 lock nuts, as shown in Figure 13.

Note: Do not fully tighten the fasteners for now.

x 16

Figure 13. Upper braces attached to stand

assembly.

3.Square up the stand, as shown in Figure 14, then tighten all the bolts.

Figure 14. Squaring stand assembly before

tightening stand hardware.

Model G0442/G0601 (Mfg Since 8/10)

Image 26

Grizzly G0601 owner manual Assembly

Contents

HP Cyclone Dust Collector Page Table of Contents Contact Info IntroductionManual Accuracy Machine Description Identification Identification Model G0442 shown Machine Data Sheet Bag Information Performance Curve G0601 Machine Data Sheet Air Suction Cap CFM @1.9 in. S.P G0601 Performance Curve Safety Safety Instructions for Machinery Unattended OPERATION. Never leave Additional Safety Instructions for Dust Collectors Full-Load Current Rating Power SupplyAvailability Circuit Requirements Grounding Instructions G0601 Circuit Requirements for 220VG0601 Circuit Requirements for 440V Grounding & Plug Requirements Extension Cords 220V Only 50 ft To rewire the Model G0601 for 440V opera- tion G0601 440V Conversion Correcting Phase Polarity G0601 Only Unpacking SetupNeeded for Setup Description Qty Collector Box Contents Figure Qty Inventory Stand Box Contents Figure Qty Contents of Filter Boxes Figure Qty Hardware Recognition Chart Site Considerations Bolting to Concrete Floors Using Machine MountsMounting to Shop Floor Assembly Foam tape attached to the intake Cylinder Aligning the mounting holes Tape Cyclone vacuum tube and hose Attachment Page Tip Use an adhesive to keep the seal in place Connecting the vacuum hose Model G0442/G0601 Mfg Since 8/10 Switch mounted to stand Model G0442/G0601 Mfg Since 8/10 To test run the dust collection system Test RunFor Model G0601 Only Ducting Materials System DesignGeneral Metal Duct Flexible Duct Plastic Duct Sketch The Shop Layout Designing Ducting SystemDecide Who Will Design Sketch a Basic Duct Layout Determine CFM of Each Machine Machine Approximate Determining Main Line Duct Diameter Machine Two Machines on Same Branch Line Determining Branch Line Duct DiameterMultiple Dust Ports Total CFM Branch Line Size Loss Per Foot Calculating Duct ResistanceDuct Approximate Dia Fitting 90˚ 45˚ Dia Elbow WyeY Closest CFM 1785 System Grounding Remote Control Operations Control Box Panel Accessories Metal Duct Starter Kit Reducers & Adapters Metal ElbowsMetal Branches G6252-4 Floor Sweep G7341-5 Floor Sweep G7342-6 Floor Sweep Schedule MaintenanceCleaning Filters Emptying Drum Tools Needed Qty Rinsing FilterRemoving/Replacing Filter To replace the canister filterPage Service Troubleshooting Refer to Designing Ducting System, beginning Wiring Wiring Safety Instructions G0442 Wiring Diagram Model G0442 G0601 Wiring Diagram Model G0601 Parts Main G0442/G0601 Common Parts List G0442 Only Parts ListG0601 Only Parts List Description Page Page Warranty Card Comments Grizzly INDUSTRIAL, INC BOX BELLINGHAM, WA Warranty and Returns Warranty and Returns Order Hours a DAY