Manuals / GTO / Household Appliance / Garage Door Opener

GTO SL-2000B, SL-1000B Connecting Safety Devices, Connecting Additional Safety Devices

Models: SL-1000B SL-2000B

1 43

Download 43 pages 59.51 Kb

Page 27

CONNECTING SAFETY DEVICES

CONNECTING SAFETY DEVICES

The GTO/PRO SL-1000 and SL-2000 series operators are equipped with built-in obstruction sensitivity. These operators are designed to stop and reverse the gate for 2 seconds when it comes in contact with an obstruction. However, obstruction sensitivity, even when properly adjusted, may not be sensitive enough to prevent bodily injury. For this reason, safety edges or photoelectric sensors MUST be installed on the gate. Safety edges (or photoelectric sensors) must be mounted in compliance with Underwriters Laboratories’ safety standard for gate operators, UL 325. Review page 6 for information about mounting requirements for safety edges and photo- electric sensors.

Refer to the sensor manufacturer’s instructions for information about installing these devices on a vehicular gate.

Make sure the control box power switch is OFF before connecting safety device wiring to the terminal blocks.

Insert the safety device wires into the CLS EDG terminal (located on the FIRST OPERATOR terminal block) for the gate closing mode. Ground the safety device at the GRN terminal. Connect the safety device wires for the gate opening mode to the OPN EDG terminal in the same manner.

MAKE SURE TO GROUND THE SAFETY DEVICES AT THE GRN TERMINAL! THE CONTROL BOARD COULD BE DAMAGED IF THE SAFETY DEVICES ARE NOT GROUNDED!

18VAC SOLAR ~ ~ – +

POWER IN

RED BLK ORG BLU GRN CLS EDG	OPN EDG
FIRST OPERATOR

RED BLK ORG BLU GRN CLS EDG OPN EDG

SECOND OPERATOR

SEQ1	ON
SEQ2	ON		LEARN
			LEARN

GRN ORG	BLU	WHT	R	B G
			R	B G
ALARM ACCESSORY				RCVR

Power Cable from First Operator

Ground Wire

Wire from Close Safety Edge or Photoelectric Sensor

Ground Wire

Wire from Open

Safety Edge or Photoelectric Sensor

CONNECTING ADDITIONAL SAFETY DEVICES

Although GTO strongly recommends the use of additional safety devices, we do not endorse any speciﬁc brand names. Only use products that are certiﬁed and listed to be in compliance with UL (United Laboratories) and national and regional safety codes.

Call GTO Sales at 1-800-543-4283 for information on compatible products for your speciﬁc application.

25

Image 27

GTO SL-2000B Connecting Safety Devices, Connecting Additional Safety Devices, Power Cable from First Operator Ground Wire

Contents

FOR VEHICULAR SLIDE GATES AUTOMATIC GATE OPERATORTABLE OF CONTENTS AUTOMATIC SLIDE GATE OPERATORS IMPORTANT SAFETY INSTRUCTIONSTO MANUALLY OPEN AND CLOSE THE GATE, FOLLOW THE PROCEDURE BELOW FOR THE GTO/PRO SL-1000/2000 AND GTO/PRO SL-1000B/2000BWARNING To reduce the risk of injury or death FOR THE INSTALLERI. Before Installation 1. READ AND FOLLOW ALL INSTRUCTIONS II. During InstallationIMPORTANT SAFETY INSTRUCTIONS III. After InstallationIMPORTANT SAFETY INSTRUCTIONS Entrapment Alarm bottom right of control boxENTRAPMENT ALARM UL 325 SECONDARY MEANS OF PROTECTION AGAINST ENTRAPMENTIMPORTANT SAFETY INSTRUCTIONS FOR THE CONSUMER/END USERWARNING To reduce the risk of injury or death NO ONE SHOULD CROSS THE PATH OF THE MOVING GATEIMPORTANT SAFETY INSTRUCTIONS REQUIRED SAFETY PRECAUTIONS FOR GATESConsult your safety manual before making adjustments IMPORTANT SAFETY INSTRUCTIONSwarning labels 3. Located on both sides and back of operator housing DO NOT remove operator housingAdjusting limit switches with power on will activate gate Continued from pageIMPORTANT SAFETY INSTRUCTIONS warning label located on limit switch plateShipping Weight GTO PRO SL-1000 SERIES TECHNICAL SPECIFICATIONSPOWER Housing DimensionsShipping Weight GTO PRO SL-2000 SERIES TECHNICAL SPECIFICATIONSPOWER Housing DimensionsPARTS IDENTIFICATION SINGLE GATE OPERATOR INSTALLATION OVERVIEW OF OPERATOR INSTALLATIONGATE PREPARATION RECOMMENDED WIRING AND USE OF CONDUIT MOUNTING THE LEGS ON THE SLIDE GATE OPERATORSTEP Roller DETERMINING THE MOUNTING POSITION AND MOUNTING THE OPERATORFence Post Gatemaster link see Illustration H INSTALLING THE CHAINQuick Release Pin ChainMake sure the control box power switch is in the OFF position POWERING THE SYSTEMCONNECTING THE BATTERY INSTALLATION OF THE GTO TRANSFORMERINSTALLATION OF THE GTO TRANSFORMER CONT SOLAR ZONES AND GATE ACTIVITYEstimated Maximum Number of Cycles Per Day INSTALLATION OF THE GTO TRANSFORMER CONT DO NOT plug the transformer into outletThe transformer will be plugged in during STEP STEPIllustration see Illustration K18VAC illustration L. TransformerCONTROL BOARD SETTINGS move the switchesRIGHT READ WARNING BELOW WARNING No other adjustments should be made inside the transmitter SETTING THE PERSONAL TRANSMITTER CODEConsider the following when mounting the receiver MOUNTING THE RECEIVERRun the cable through PVC conduit to protect it from damage Counter Clockwise ADJUSTING THE LIMIT SWITCHESIf your gate opens from Right to Left However, if your gate opens from Left to RightGround Wire Wire from Open Safety Edge or Photoelectric Sensor CONNECTING SAFETY DEVICESCONNECTING ADDITIONAL SAFETY DEVICES Power Cable from First Operator Ground WireORG ORANGE USED WITH GRN GREEN CONNECTING ACCESSORIESWHT WHITE USED WITH GRN GREEN BLU BLUE USED WITH GRN GREENIMPORTANT Safety Instructions ATTACHING THE HOUSINGMAINTENANCE Maintenance TROUBLE SHOOTING GUIDESYSTEM TEST SPECIFICATIONS The GTO, Inc. Technical Service Department is openTELEPHONE 800 543-1236 OR 850 connected to these terminalsLimited Two Year Warranty WARRANTY AND REPAIR SERVICEAUTOMATIC GATE OPERATORS AUTOMATIC GATE OPERATORS INSTRUCTIONS FOR THE INSTALLATION OF A DUAL SLIDE GATE SYSTEMUse the SL-1200 with the SL-1000 and the SL-2200 with the SL-2000 for dual slide gate systemsSECOND GATE AUXILIARY OPERATOR PARTS & HARDWARE DUAL GATE SYSTEM INSTALLATIONSecond Gate Operator PREPARING THE GATESFirst Gate Operator Control UnitTHIS STEP IS FOR SL-2000/2200 INSTALLATION ONLY WIRING THE SECOND OPERATORRefer to the illustrations on the next page SETTING THE CONTROL BOARD FOR DUAL GATE INSTALLATIONSFIRST OPERATOR OPENS FIRST, SECOND OPERATOR CLOSES FIRST STEPACCESSORIES If you have a question about any special order item just call 1-800-543-GATE#41 Slide Gate Chain RB207 VEHICULAR GATE OPERATOR CLASS CATEGORIES Conversion ChartWhen You Know SymbolINSTALLATION CHECK LIST The installation of this operator conforms to CLASSINSTRUCTIONS