Safety Alert Key:
•DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
•WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
•CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
•NOTICE: Used to address practices not related to personal injury.
Table of Contents
A. | Congratulations | 2 |
B. | Limited Lifetime Warranty | 5 |
1 Listing and Code Approvals
A. | Appliance Certification | 6 |
B. | Tempered Glass Specifications | 6 |
C. | BTU Specifications | 6 |
D. | High Altitude Installations | 6 |
E. | 6 | |
F. | Combustible Materials Specification | 6 |
G. | Requirements for the |
|
| Commonwealth of Massacusetts | 7 |
User Guide
2 Operating Instructions
A. | Gas Fireplace Safety | 8 |
B. | Your Fireplace | 8 |
C. | Fan Kit (optional) | 9 |
D. | Clear Space | 9 |
E. | Decorative Doors and Fronts | 9 |
F. | Fixed Glass Assembly | 9 |
G. | Remote Controls, Wall Controls and Wall Switches 9 | |
H. | Before Lighting Fireplace | 9 |
I. | Intermittent Pilot Ignition (IPI) | 10 |
J. | Standing Pilot Ignition | 11 |
K. | After Appliance is Lit | 12 |
L. | Frequently Asked Questions | 12 |
3 Maintenance and Service |
| |
A. | Maintenance | 13 |
B. | Maintenance | 14 |
Installer Guide
4 Getting Started |
| |
A. | Typical Appliance System | 16 |
B. | Design and Installation Considerations | 17 |
C. Tools and Supplies Needed | 17 | |
D. Inspect Appliance and Components | 17 | |
5 Framing and Clearances |
| |
A. | Select Appliance Location | 18 |
B. | Constructing the Appliance Chase | 19 |
C. | Clearances | 19 |
D. | Mantel and Wall Projections | 20 |
6 Termination Locations
A. Vent Termination Minimum Clearances | 21 |
7 Vent Information and Diagrams
A. | Approved Pipe | 23 |
B. | Vent Table Key | 23 |
C. | Use of Elbows | 23 |
D. | Measuring Standards | 23 |
E. | Vent Diagrams | 24 |
8 Vent Clearances and Framing
A. | Pipe Clearances to Combustibles | 33 |
B. | Wall Penetration Framing | 33 |
C. | Install the Ceiling Firestop | 34 |
D. | Install Attic Insulation Shield | 35 |
9 Appliance Preparation
A. | Top Vent | 36 |
B. | Rear Vent | 37 |
C. | Secure and Level the Appliance | 38 |
10 Installing Vent Pipe
A. | Assemble Vent Sections (DVP only) | 39 |
B. | Assemble Vent Sections (SLP Pipe Only) | 40 |
C. | Assemble MI Sections (DVP only) | 40 |
D. | Assemble Slip Sections | 41 |
E. | Secure the Vent Sections | 42 |
F. | Disassemble Vent Sections | 42 |
G. | Install Decorative Ceiling Components (SLP only) 43 | |
H. | Install Metal Roof Flashing | 44 |
I. | Install | 45 |
J. | Install Vertical Termination Cap | 46 |
K. | Assemble and Install Storm Collar | 46 |
L.Install Heat Shields and
| Horizontal Termination Cap | 47 |
11 Gas Information |
| |
A. | Fuel Conversion | 49 |
B. | Gas Pressure | 49 |
C. | Gas Connection | 49 |
D. | High Altitude Installations | 49 |
12 Electrical Information |
| |
A. | Wiring Requirements | 50 |
B. | Standing Pilot Ignition System Wiring | 50 |
C. | Intellifire Ignition System Wiring | 50 |
D. | Optional Accessories Requirements | 50 |
E. | Electrical Service and Repair | 51 |
F. | Junction Box Installation | 52 |
G. | Wall Switch Installation for Fan (Optional) | 52 |
13 Finishing |
| |
A. | Mantel and Wall Projections | 53 |
B. | Facing Material | 54 |
Heatilator • Novus NDV Series • | 3 |
