Manuals / Hearth and Home Technologies / Household Appliance / Indoor Fireplace

Hearth and Home Technologies NDV4236IL, NDV3630, NDV3933L, NDV4842IL, NDV4842L Dvp-Hrc-Zc-Ss

Models: NDV3933IL NDV3036IL NDV4236L NDV4842L NDV4236I NDV3933L NDV4236IL NDV4842 NDV3630L NDV3933I NDV4842IL NDV4236 NDV4842I NDV3630 NDV3933 NDV3630I

1 84

Download 84 pages 46.5 Kb

Page 69

B. Vent Components Diagrams (continued)

Fillers

ÎDVP-TRAP to DVP-HPC Side Filler Kit

8-1/8 in.

(206 mm)

15in.

(381 mm)

13in.

(330 mm)

DVP-HRC-SS

(Not approved for NDV4842)

Effective Length 5-3/4 to 8-3/8 in. 146 to 213 mm

	5-1/2 in.		8-3/8 in.
	140 mm		213 mm

	87°	3°

10-1/2 in.

267 mm

10-7/8 in.

276 mm

DVP-HRC-ZC-SS

(Not approved for NDV4842)

Figure 16.6 DVP Vent Components

Heatilator • Novus NDV Series • 4055-187 Rev F • 06/08

69

Image 69

Hearth and Home Technologies NDV4236IL, NDV3933L, NDV4842IL, NDV4842L, NDV4236L, NDV3933I, NDV3630L Dvp-Hrc-Zc-Ss

Contents

Models Installation and OperationWhat to do if you smell gas Hot glass will cause burns Homeowner Reference Information Congratulations Table of Contents Installer GuideUser Guide Troubleshooting Limited Lifetime Warranty Gas Appliance Fireplace Limited Lifetime Warranty Listing and Code Approvals Requirements for the Commonwealth of Massacusetts Gas Fireplace Safety Operating InstructionsYour Fireplace Remote Controls, Wall Controls and Wall Switches Fixed Glass AssemblyFan Kit optional Clear Space Ignition IPI For Your Safety Read Before Lighting Ignition Standing Pilot After Appliance is Lit Frequently Asked Questions Maintenance Tasks-Homeowner Maintenance and ServiceGlass Cleaning Remote Control Gasket Seal and Glass Assembly Inspection Maintenance Tasks-Service TechnicianVenting Logs Either cobrahead or SIT Typical Appliance System Getting Started Tools and Supplies Needed Design and Installation ConsiderationsInspect Appliance and Components Any such action may cause a ﬁre hazard Framing and Clearances Select Appliance LocationModel Clearances Constructing the Appliance Chase Mantels Mantel Legs or Wall Projections Mantel and Wall Projections Vent Termination Minimum Clearances Termination Locations Minimum Clearances for Terminations Approved Pipe Vent Information and DiagramsMeasuring Standards Vent Table Key Top Vent Horizontal Termination Two 45 Elbows Vent Diagrams Top Vent Horizontal Termination One Elbow Two ElbowsMin Max Three Elbows Install Top Vent Flue Visor No Elbow Conﬁgura- tions Top Vent Vertical TerminationNo Elbow 12 ft 3.66 m min 60 ft 18.29 m max One 45 Elbow Rear Vent Horizontal Termination DVP only Total Vert Total Horiz Model Max Min + H 2 + H Two Elbows Three Elbows One Elbow Rear Vent Vertical Termination DVP only Min Ft 1.83 m max 12 ft 3.66 m min 60 ft 18.29 m max Pipe Clearances to Combustibles Vent Clearances and FramingWall Penetration Framing Model Top Vent Rear Vent Installing Ceiling Firestop Install the Ceiling Firestop Flat Ceiling Installation Install Attic Insulation Shield Top Vent Appliance Preparation Rear Vent Secure and Level the Appliance Attach Vent to the Firebox Assembly Installing Vent PipeAssemble Vent Sections DVP only Assemble Pipe Sections Assemble Vent Sections SLP Pipe Only Assemble MI Sections DVP onlyCut from this end Outer Inner Slip Section Pilot Holes Assemble Slip Sections Disassemble Vent Sections Secure the Vent Sections Install Decorative Ceiling Components SLP only 15 Minimum Height From Roof To Lowest Discharge Opening Install Metal Roof Flashing SLP-FS Install RF4-8 Assemble and Install Storm Collar Install Vertical Termination Cap Heat Shield Requirements for Horizontal Termi- nation Install Heat Shields and Horizontal Termi Nation Cap Interior Install Horizontal Termination Cap Fuel Conversion Gas InformationGas Pressure Gas Connection Standing Pilot Ignition System Wiring Wiring RequirementsIntelliﬁre Ignition System Wiring Optional Accessories Requirements WSK-MLT-HTL Electrical Service and Repair Wall Switch Installation for Fan Optional Junction Box Installation Mantels Finishing Facing Material Noncombustible Facing Diagram Appliance Setup Place the Lava Rock Place the RockwoolPlace the Vermiculite Remove Screen Protector Unpackage the Hood & Floor Cover Install Hood Close the Screen Assembly Install Floor CoverRemoving Fixed Glass Assembly Replacing Fixed Glass Assembly 14 Adjusting Air Shutter Air Shutter Setting Troubleshooting Symptom Possible Causes Corrective ActionStanding Pilot Ignition System Symptom Possible Cause Corrective Action Troubleshooting Intelliﬁre Ignition System Will not ignite. If the pilot Reference Materials Appliance Dimension Diagram DVP Pipe Vent Components Diagrams RF6M RF12M Extended Heat Shield DVP-TVHW Horizontal Termination Cap DVP-TRAP DVP-HRC-ZC-SS Effective SLK-SNKD SLP-CCS-BK Parts Service Parts NDV3630 & NDV3630I IPI Valve Standing Pilot Valve Service Parts NDV3933 & NDV3933I 187 Service Parts NDV4236 & NDV4236I 4055-187 Service Parts NDV4842 & NDV4842I Stocked Model # Description Optional Components WTB36 This page intentionally left blank This page intentionally left blank Contact Information