Manuals / Hearth and Home Technologies / Household Appliance / Indoor Fireplace

Hearth and Home Technologies NDV4842L, NDV4236IL, NDV3630, NDV3933L, NDV4842I Slk-Snkd Slp-Ccs-Bk

Models: NDV3933IL NDV3036IL NDV4236L NDV4842L NDV4236I NDV3933L NDV4236IL NDV4842 NDV3630L NDV3933I NDV4842IL NDV4236 NDV4842I NDV3630 NDV3933 NDV3630I

1 84

Download 84 pages 46.5 Kb

Page 71

B. Vent Components Diagrams (continued)

Î SLK-SNKD	SLP-CCS-BK	SLP-TVHW
Snorkel	Cathedral Ceiling Sup-	Vertical
Termination Cap	port Box-Black	Termination Cap

8-1/8 in.

(206 mm)

15 in.

(381 mm)

PVK-80

Power Vent

13 in.

(330 mm)

SLP-TRAP1	DVP-FBHT	SLP-HRC-SS
SLP-TRAP1	Horizontal	SLP-HRC-SS
Horizontal	Termination Cap	(Not approved for NDV4842)
Termination Cap

Effective Length 5-3/4 to 8-3/8 in. 146 to 213 mm

	5-1/2 in.		8-3/8 in.
	140 mm		213 mm

	87°	3°

10-1/2 in.

267 mm

10-7/8 in.

276 mm

	SLP-TRAP2	SLP-HRC-ZC-SS
	Horizontal
		(Not approved for NDV4842)
	Termination Cap

Î Figure 16.8 SLP Series Vent Components

Heatilator • Novus NDV Series • 4055-187 Rev F • 06/08

71

Image 71

Hearth and Home Technologies NDV4842L, NDV4236IL, NDV3630, NDV3933L, NDV4842IL, NDV4236L, NDV3933I Slk-Snkd Slp-Ccs-Bk

Contents

Hot glass will cause burns Installation and OperationModels What to do if you smell gas Homeowner Reference Information Congratulations User Guide Table of ContentsInstaller Guide Troubleshooting Limited Lifetime Warranty Gas Appliance Fireplace Limited Lifetime Warranty Listing and Code Approvals Requirements for the Commonwealth of Massacusetts Your Fireplace Gas Fireplace SafetyOperating Instructions Clear Space Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Fan Kit optional Ignition IPI For Your Safety Read Before Lighting Ignition Standing Pilot After Appliance is Lit Frequently Asked Questions Remote Control Maintenance and ServiceMaintenance Tasks-Homeowner Glass Cleaning Logs Maintenance Tasks-Service TechnicianGasket Seal and Glass Assembly Inspection Venting Either cobrahead or SIT Typical Appliance System Getting Started Any such action may cause a ﬁre hazard Design and Installation ConsiderationsTools and Supplies Needed Inspect Appliance and Components Model Framing and ClearancesSelect Appliance Location Clearances Constructing the Appliance Chase Mantels Mantel Legs or Wall Projections Mantel and Wall Projections Vent Termination Minimum Clearances Termination Locations Minimum Clearances for Terminations Vent Table Key Vent Information and DiagramsApproved Pipe Measuring Standards Top Vent Horizontal Termination Two 45 Elbows Vent Diagrams Min Max Top Vent Horizontal TerminationOne Elbow Two Elbows Three Elbows No Elbow Install Top Vent Flue Visor No Elbow Conﬁgura- tionsTop Vent Vertical Termination 12 ft 3.66 m min 60 ft 18.29 m max One 45 Elbow Rear Vent Horizontal Termination DVP only Total Vert Total Horiz Model Max Min + H 2 + H Two Elbows Three Elbows One Elbow Rear Vent Vertical Termination DVP only Min Ft 1.83 m max 12 ft 3.66 m min 60 ft 18.29 m max Model Top Vent Rear Vent Vent Clearances and FramingPipe Clearances to Combustibles Wall Penetration Framing Installing Ceiling Firestop Install the Ceiling Firestop Flat Ceiling Installation Install Attic Insulation Shield Top Vent Appliance Preparation Rear Vent Secure and Level the Appliance Assemble Pipe Sections Installing Vent PipeAttach Vent to the Firebox Assembly Assemble Vent Sections DVP only Cut from this end Outer Inner Assemble Vent Sections SLP Pipe OnlyAssemble MI Sections DVP only Slip Section Pilot Holes Assemble Slip Sections Disassemble Vent Sections Secure the Vent Sections Install Decorative Ceiling Components SLP only 15 Minimum Height From Roof To Lowest Discharge Opening Install Metal Roof Flashing SLP-FS Install RF4-8 Assemble and Install Storm Collar Install Vertical Termination Cap Heat Shield Requirements for Horizontal Termi- nation Install Heat Shields and Horizontal Termi Nation Cap Interior Install Horizontal Termination Cap Gas Connection Gas InformationFuel Conversion Gas Pressure Optional Accessories Requirements Wiring RequirementsStanding Pilot Ignition System Wiring Intelliﬁre Ignition System Wiring WSK-MLT-HTL Electrical Service and Repair Wall Switch Installation for Fan Optional Junction Box Installation Mantels Finishing Facing Material Noncombustible Facing Diagram Appliance Setup Remove Screen Protector Place the RockwoolPlace the Lava Rock Place the Vermiculite Unpackage the Hood & Floor Cover Install Hood Replacing Fixed Glass Assembly Install Floor CoverClose the Screen Assembly Removing Fixed Glass Assembly 14 Adjusting Air Shutter Air Shutter Setting Standing Pilot Ignition System TroubleshootingSymptom Possible Causes Corrective Action Symptom Possible Cause Corrective Action Troubleshooting Intelliﬁre Ignition System Will not ignite. If the pilot Reference Materials Appliance Dimension Diagram DVP Pipe Vent Components Diagrams RF6M RF12M Extended Heat Shield DVP-TVHW Horizontal Termination Cap DVP-TRAP DVP-HRC-ZC-SS Effective SLK-SNKD SLP-CCS-BK Parts Service Parts NDV3630 & NDV3630I IPI Valve Standing Pilot Valve Service Parts NDV3933 & NDV3933I 187 Service Parts NDV4236 & NDV4236I 4055-187 Service Parts NDV4842 & NDV4842I Stocked Model # Description Optional Components WTB36 This page intentionally left blank This page intentionally left blank Contact Information