7 Vent Information and Diagrams
A. Approved Pipe
This appliance is approved for use with Hearth & Home
ÎTechnologies DVP and SLP venting systems. Refer to Sec- tion 16B for vent component information.
DO NOT mix pipe, fittings or joining methods from different manufacturers.
The pipe is tested to be run inside an enclosed wall. There is no requirement for inspection openings at each joint within the wall.
WARNING! Risk of Fire or Asphyxiation. This appliance requires a separate vent. DO NOT vent to a pipe serving a separate solid fuel burning appliance.
D. Measuring Standards
Vertical and horizontal measurements listed in the vent diagrams were made using the following standards.
•Pipe measurements are shown using the effective length of pipe (see Figure 7.2).
•Measurements are made from the appliance outer wrap, not from the standoffs.
•Horizontal terminations are measured to the outside mounting surface (flange of termination cap) (see Figure 6.5).
•Vertical terminations are measured to bottom of termination cap.
•Horizontal pipe installed level with no rise.
B. Vent Table Key
The abbreviations listed in this vent table key are used in the vent diagrams.
Symbol | Description |
|
|
V1 | First section (closest to appliance) of vertical length |
|
|
V2 | Second section of vertical length |
|
|
H1 | First section (closest to appliance) of horizontal length |
|
|
H2 | Subsequent sections of horizontal length |
|
|
C. Use of Elbows
Diagonal runs have both vertical and horizontal vent aspects when calculating the effects. Use the rise for the vertical aspect and the run for the horizontal aspect (see Figure 7.1).
Two 45º elbows may be used in place of one 90º elbow. On 45º runs, one foot of diagonal is equal to
Vertical in.1/2
Horizontal 
Figure 7.1
|
|
|
|
|
|
|
|
| Effective Height/Length | ||||
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
| Pipe |
| inches |
| mm |
|
|
|
|
|
|
|
|
| DVP4 |
| 4 |
| 102 |
|
|
|
|
|
|
|
|
| DVP6 |
| 6 |
| 152 |
|
|
|
|
|
|
|
|
| |||||
|
|
| Effective |
| |||||||||
|
|
|
| DVP12 |
| 12 |
| 305 | |||||
|
| Height/Length |
|
|
| ||||||||
|
|
| DVP24 |
| 24 |
| 610 | ||||||
|
|
|
|
|
|
|
|
| DVP36 |
| 36 |
| 914 |
|
|
|
|
|
|
|
|
| DVP48 |
| 48 |
| 1219 |
|
|
|
|
|
|
|
|
| DVP6A |
| 3 - 6 |
| 76 - 152 |
|
|
|
|
|
|
|
|
| DVP12A |
| 3 - 12 |
| 76 - 305 |
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
| DVP12MI |
| 3 - 12 |
| 76 - 305 |
DVP Pipe |
| DVP24MI |
| 3 - 24 |
| 76 - 610 | |||||||
|
|
|
|
|
| ||||||||
(see chart) |
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Effective Height/Length | ||||
|
|
|
|
|
|
|
|
| Pipe |
| inches |
| mm |
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
| SLP4 | 4 | 102 | ||
|
| Effective |
|
| |||||||||
|
|
|
| SLP6 | 6 | 152 | |||||||
| Height/Length |
|
| ||||||||||
|
|
| SLP12 | 12 | 305 | ||||||||
|
|
|
|
|
|
|
|
| SLP24 | 24 | 610 | ||
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
| SLP36 | 36 | 914 | ||
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
| SLP48 | 48 | 1219 | ||
SLP Pipe |
| SLP6A | 2 - 6 | 51 - 152 | |||||||||
| SLP12A | 2 - 12 | 51 - 305 | ||||||||||
(see chart) |
| ||||||||||||
|
|
|
|
|
| ||||||||
ÎFigure 7.2 Pipe Effective Length
Heatilator • Novus NDV Series • | 23 |
