Manuals / Heat & Glo LifeStyle / Household Appliance / Indoor Fireplace

Heat & Glo LifeStyle 6000 XLT, 8000 DVTFL, SL-42 DVT, 6000 ARCH inchinner pipe/6 5/8-inchouter pipe

Models: 8000 DVTFL 6000 XLT 6000 ARCH 6000 DVTFL SL-42 DVT

1 46

Download 46 pages 22.06 Kb

Page 13

(4-inch inner pipe/6 5/8-inch outer pipe)

Figure 8. SL-D-Series Direct Vent Component Specifications

(4-inch inner pipe/6 5/8-inch outer pipe)

10

Image 13

Heat & Glo LifeStyle 6000 XLT, 8000 DVTFL, SL-42 DVT, 6000 ARCH, 6000 DVTFL manual inchinner pipe/6 5/8-inchouter pipe

Contents

Installers Guide Underwriters Laboratories ListedHeat-N-GloFireplace 8000 DVTFL THIS UNIT IS NOT FOR USE WITH SOLID FUEL SAFETY AND WARNING INFORMATIONPROHIBITED Table of Contents and Codes Approvals and CodesInstallation Codes High Altitude Installations Introducing the Heat-N-Glo Gas Fireplaces Pre-installationPreparationGetting Started ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD Figure 1. Diagram of 8000DVTFL Page Figure 3. Diagram of SL-42DVT Step Locating the Fireplace Installing the FireplaceClearance Requirements VERIFY FRAMING METHODS AND WALL Step Framing the FireplaceCOVERING DETAILS, BEFORE FRAMING CONSTRUCTION BEGINS A. Vent System Approvals Step Installing the Vent System DV-45D DV-90DDV-48D DV-36D DV-12D 4-inchinner pipe/6 5/8-inchouter pipe VERTICAL VENTING V FT 40 MAX. 12.4 M Figure 9. Vertical VentingNOTE MODEL 6000 ARCH FOR SL-42DVT Model 6000XLT & 8000DVTFLNOTE: IF A 90 ELBOW IS FIRST ATTACHED TO THE UNIT, THE Figure 11. Venting with two 90 elbows VENTING WITH TWO 2 90 ELBOWSNOTE MODEL 6000 ARCH H1 V H Figure 12. Venting with two 90 elbows VENTING WITH TWO 2 90 ELBOWSNOTE: MODEL 6000 ARCH H V1 V Figure 13. Venting with three 90 elbows VENTING WITH THREE 3 90 ELBOWSNOTE: MODEL 6000 ARCH Figure 14. Venting with three 90 elbows VENTING WITH THREE 3 90 ELBOWS B. Installing Vent Components ENSURE THAT THE FIBERGLASS To install support brackets for horizontal runs 3. Install Support BracketsFigure 17. Adding Venting Components •Place the pipe supports around the vent pipe 4. Install Firestops Figure 18. Installing Support BracketsFor Horizontal Runs - Firestops are REQUIRED Model DVK-01TRDand SLK-01TRDdo not need Figure 19. Hole and Vent Pipe Figure 22. Ceiling Firestop Ceiling Side Figure 21. Hole and New Framing Members Figure 23. Attic Firestop C. Vent Termination Figure 24. Round and Trapezoid Termination Caps IF EXTERIOR WALLS ARE FINISHED WITH VINYL SIDING, IT IS NECESSARY TO INSTALLTHE VINYL PROTECTOR KIT TO THE TOP OF TERMINATION CAPS on the outside of the building MAJOR U.S. BUILDING CODES Roof Pitch Fireplace Step Positioning Leveling, and Securing theStep The Gas Control Systems Figure 28. Gas Controls Systems Step The Gas Supply Line13 mm hook-upat the unit DO NOT USE AN OPEN FLAME TO CHECK FOR GAS LEAKS Figure 29. Gas Supply Line Step Gas Pressure RequirementsPressure Natural Gas For Standing Pilot Ignition Wiring Step Wiring the Fireplace LABEL ALL WIRES PRIOR TO DISCONNECTION Electrical wiring must be installed by a licensedWHEN SERVICING CONTROLS. WIRING ERRORS CAN CAUSE IMPROPER AND Step Finishing Hearth Extensions Step Installing Trim Logs, and Ember Material Save the log instructions with this manual Positioning the LogsPlacing the Ember Material Figure 36. Placement of the Ember Material Figure 35. Glass Assembly1.Lift the trim door up and out of the unit Step Before Lighting the Fireplace Step Lighting the Fireplace After the InstallationReview safety warnings and cautions Double-checkfor faulty components Maintaining and Servicing Your Fireplace Fireplace MaintenanceTURN OFF THE GAS BEFORE SERVICING YOUR FIREPLACE Figure 38. Pilot/Ignitor Flame Patterns Figure 37. Burner Flame Patterns Standing Pilot Only Replacement Parts and AccessoriesPART PART DESCRIPTION 8000DVTFL, 6000DVTFL, 6000ARCH, SL-42DVT DSI Ignition OnlyPART PART DESCRIPTION Both Standing Pilot and DSI Ignition Both Standing Pilot and DSI Ignition Cont AccessoriesACCESSORY PART