Manuals / Heat & Glo LifeStyle / Household Appliance / Indoor Fireplace

Heat & Glo LifeStyle SL-42 DVT VENTING WITH TWO 2 90 ELBOWS, Venting with two 90 elbows, H1 V H

Models: 8000 DVTFL 6000 XLT 6000 ARCH 6000 DVTFL SL-42 DVT

1 46

Page 16

VENTING WITH TWO (2) 90° ELBOWS

V (FT.)		H + H1 (FT.) (8000 & 6000’s)	H + H1 (FT.) (SL-42DVT)
1'	MIN. (305 mm)	6' MAX. (1.86 m)	3'	MAX. (914 mm)
2'	MIN. (610 mm)	12' MAX. (3.72 m)	6'	MAX. (1.83 m)
3'	MIN. (914 mm)	18' MAX. (5.58 m)	9'	MAX. (2.74 m)
4'	MIN. (1.22 m)	24' MAX. (8.44 m)	12' MAX. (3.66 m)
20' MAX. (6.2 m)		24' MAX. (8.44 m)	12' MAX. (3.66 m)
		(21' IN CANADA 6.5 m)

NOTE: MODEL 6000 ARCH

A 12-inch length of straight vent pipe MUST be the first vent component attached to the unit.

H1

Figure 11. Venting with two 90° elbows

Page 16

Image 16

Heat & Glo LifeStyle SL-42 DVT VENTING WITH TWO 2 90 ELBOWS, Venting with two 90 elbows, NOTE MODEL 6000 ARCH, H1 V H

Contents

Underwriters Laboratories Listed Installers GuideHeat-N-GloFireplace 8000 DVTFL THIS UNIT IS NOT FOR USE WITH SOLID FUEL SAFETY AND WARNING INFORMATIONPROHIBITED Table of Contents Approvals and Codes and CodesInstallation Codes High Altitude Installations Pre-installationPreparation Introducing the Heat-N-Glo Gas FireplacesGetting Started ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD Figure 1. Diagram of 8000DVTFL Page Figure 3. Diagram of SL-42DVT Step Locating the Fireplace Installing the FireplaceClearance Requirements Step Framing the Fireplace VERIFY FRAMING METHODS AND WALLCOVERING DETAILS, BEFORE FRAMING CONSTRUCTION BEGINS Step Installing the Vent System A. Vent System Approvals DV-90D DV-45DDV-48D DV-36D DV-12D 4-inchinner pipe/6 5/8-inchouter pipe VERTICAL VENTING V FT 40 MAX. 12.4 M Figure 9. Vertical VentingNOTE MODEL 6000 ARCH Model 6000XLT & 8000DVTFL FOR SL-42DVTNOTE: IF A 90 ELBOW IS FIRST ATTACHED TO THE UNIT, THE VENTING WITH TWO 2 90 ELBOWS Figure 11. Venting with two 90 elbowsNOTE MODEL 6000 ARCH H1 V H VENTING WITH TWO 2 90 ELBOWS Figure 12. Venting with two 90 elbowsNOTE: MODEL 6000 ARCH H V1 V Figure 13. Venting with three 90 elbows VENTING WITH THREE 3 90 ELBOWSNOTE: MODEL 6000 ARCH VENTING WITH THREE 3 90 ELBOWS Figure 14. Venting with three 90 elbows B. Installing Vent Components ENSURE THAT THE FIBERGLASS 3. Install Support Brackets To install support brackets for horizontal runsFigure 17. Adding Venting Components •Place the pipe supports around the vent pipe Figure 18. Installing Support Brackets 4. Install FirestopsFor Horizontal Runs - Firestops are REQUIRED Model DVK-01TRDand SLK-01TRDdo not need Figure 19. Hole and Vent Pipe Figure 21. Hole and New Framing Members Figure 22. Ceiling Firestop Ceiling Side C. Vent Termination Figure 23. Attic Firestop Figure 24. Round and Trapezoid Termination Caps VINYL SIDING, IT IS NECESSARY TO INSTALL IF EXTERIOR WALLS ARE FINISHED WITHTHE VINYL PROTECTOR KIT TO THE TOP OF TERMINATION CAPS MAJOR U.S. BUILDING CODES on the outside of the building Roof Pitch Fireplace Step Positioning Leveling, and Securing theStep The Gas Control Systems Step The Gas Supply Line Figure 28. Gas Controls Systems13 mm hook-upat the unit DO NOT USE AN OPEN FLAME TO CHECK FOR GAS LEAKS Step Gas Pressure Requirements Figure 29. Gas Supply LinePressure Natural Gas Step Wiring the Fireplace For Standing Pilot Ignition Wiring Electrical wiring must be installed by a licensed LABEL ALL WIRES PRIOR TO DISCONNECTIONWHEN SERVICING CONTROLS. WIRING ERRORS CAN CAUSE IMPROPER AND Step Finishing Step Installing Trim Logs, and Ember Material Hearth Extensions Save the log instructions with this manual Positioning the LogsPlacing the Ember Material Figure 36. Placement of the Ember Material Figure 35. Glass Assembly1.Lift the trim door up and out of the unit Lighting the Fireplace After the Installation Step Before Lighting the Fireplace StepReview safety warnings and cautions Double-checkfor faulty components Fireplace Maintenance Maintaining and Servicing Your FireplaceTURN OFF THE GAS BEFORE SERVICING YOUR FIREPLACE Figure 37. Burner Flame Patterns Figure 38. Pilot/Ignitor Flame Patterns Replacement Parts and Accessories Standing Pilot OnlyPART PART DESCRIPTION DSI Ignition Only 8000DVTFL, 6000DVTFL, 6000ARCH, SL-42DVTPART PART DESCRIPTION Both Standing Pilot and DSI Ignition Accessories Both Standing Pilot and DSI Ignition ContACCESSORY PART