Manuals / Heat & Glo LifeStyle / Household Appliance / Indoor Fireplace

Heat & Glo LifeStyle 8000 DVTFL Electrical wiring must be installed by a licensed, electrician

Models: 8000 DVTFL 6000 XLT 6000 ARCH 6000 DVTFL SL-42 DVT

1 46

Download 46 pages 22.06 Kb

Page 35

Electrical wiring must be installed by a licensed

									FAN WIRING DIAGRAM
									VARIABLE SPEED CONTROL


BLK									BLK

		JUNCTION BOX
BLK	BLK
	BLK	BLK
		BLK
BLK		BLK
		BLK
		WHT
		BLK
		GROUND
TEMPERATURE
SENSOR SWITCH
		GRN
		BLK	WHT
			WHT
		110-120 VAC

NOTE: IF ANY OF THE ORIGINAL WIRE AS SUPPLIED WITH THE APPLIANCE MUST BE REPLACED, IT MUST BE REPLACED WITH TYPE 105 DEGREE C RATED WIRE.

BLOWER RECEPTACLE

BLK

WHT

BLOWER

JUNCTION	TEMPERATURE
BOX	SENSOR SWITCH

FAN	SPEED CONTROL
	(RHEOSTAT)

Figure 31. Fan Wiring Diagram

	For Direct Spark Ignition (DSI) Wiring
	Appliance Requirements
	This appliance requires that 110-120 VAC be wired to
	the factory installed junction box. Maintain correct
	polarity when wiring the junction box.
	Optional Accessories
	Optional fan and remote control kits require that 110-
	120 VAC be wired to the fireplace junction box.
	Remote Wall Switch
	Position the remote wall switch in the desired position
	on a wall. Run a maximum of 25 feet
	(7.8 m) or less of 16 A.W.G. minimum wire and
	connect it to the fireplace ON/OFF switch pigtails.
NOTE	Electrical wiring must be installed by a licensed
	electrician.
CAUTION	LABEL ALL WIRES PRIOR TO DISCONNECTION
	WHEN SERVICING CONTROLS. WIRING
	ERRORS CAN CAUSE IMPROPER AND
	DANGEROUS OPERATION. VERIFY PROPER	32
	OPERATION AFTER SERVICING.	32
	OPERATION AFTER SERVICING.

Image 35

Heat & Glo LifeStyle 8000 DVTFL Electrical wiring must be installed by a licensed, electrician, Operation After Servicing

Contents

8000 DVTFL Underwriters Laboratories ListedInstallers Guide Heat-N-GloFireplacePROHIBITED SAFETY AND WARNING INFORMATIONTHIS UNIT IS NOT FOR USE WITH SOLID FUEL Table of Contents High Altitude Installations Approvals and Codesand Codes Installation CodesANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD Pre-installationPreparationIntroducing the Heat-N-Glo Gas Fireplaces Getting StartedFigure 1. Diagram of 8000DVTFL Page Figure 3. Diagram of SL-42DVT Clearance Requirements Installing the FireplaceStep Locating the Fireplace CONSTRUCTION BEGINS Step Framing the FireplaceVERIFY FRAMING METHODS AND WALL COVERING DETAILS, BEFORE FRAMINGA. Vent System Approvals Step Installing the Vent SystemDV-12D DV-90DDV-45D DV-48D DV-36D4-inchinner pipe/6 5/8-inchouter pipe NOTE MODEL 6000 ARCH Figure 9. Vertical VentingVERTICAL VENTING V FT 40 MAX. 12.4 M ATTACHED TO THE UNIT, THE Model 6000XLT & 8000DVTFLFOR SL-42DVT NOTE: IF A 90 ELBOW IS FIRSTH1 V H VENTING WITH TWO 2 90 ELBOWSFigure 11. Venting with two 90 elbows NOTE MODEL 6000 ARCHH V1 V VENTING WITH TWO 2 90 ELBOWSFigure 12. Venting with two 90 elbows NOTE: MODEL 6000 ARCHNOTE: MODEL 6000 ARCH VENTING WITH THREE 3 90 ELBOWSFigure 13. Venting with three 90 elbows Figure 14. Venting with three 90 elbows VENTING WITH THREE 3 90 ELBOWSB. Installing Vent Components ENSURE THAT THE FIBERGLASS •Place the pipe supports around the vent pipe 3. Install Support BracketsTo install support brackets for horizontal runs Figure 17. Adding Venting ComponentsModel DVK-01TRDand SLK-01TRDdo not need Figure 18. Installing Support Brackets4. Install Firestops For Horizontal Runs - Firestops are REQUIREDFigure 19. Hole and Vent Pipe Figure 22. Ceiling Firestop Ceiling Side Figure 21. Hole and New Framing MembersFigure 23. Attic Firestop C. Vent TerminationFigure 24. Round and Trapezoid Termination Caps TERMINATION CAPS VINYL SIDING, IT IS NECESSARY TO INSTALLIF EXTERIOR WALLS ARE FINISHED WITH THE VINYL PROTECTOR KIT TO THE TOP OFon the outside of the building MAJOR U.S. BUILDING CODESRoof Pitch Step The Gas Control Systems Step Positioning Leveling, and Securing theFireplace DO NOT USE AN OPEN FLAME TO CHECK FOR GAS LEAKS Step The Gas Supply LineFigure 28. Gas Controls Systems 13 mm hook-upat the unitNatural Gas Step Gas Pressure RequirementsFigure 29. Gas Supply Line PressureFor Standing Pilot Ignition Wiring Step Wiring the FireplaceERRORS CAN CAUSE IMPROPER AND Electrical wiring must be installed by a licensedLABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING CONTROLS. WIRINGStep Finishing Hearth Extensions Step Installing Trim Logs, and Ember MaterialPlacing the Ember Material Positioning the LogsSave the log instructions with this manual 1.Lift the trim door up and out of the unit Figure 35. Glass AssemblyFigure 36. Placement of the Ember Material Double-checkfor faulty components Lighting the Fireplace After the InstallationStep Before Lighting the Fireplace Step Review safety warnings and cautionsYOUR FIREPLACE Fireplace MaintenanceMaintaining and Servicing Your Fireplace TURN OFF THE GAS BEFORE SERVICINGFigure 38. Pilot/Ignitor Flame Patterns Figure 37. Burner Flame PatternsPART DESCRIPTION Replacement Parts and AccessoriesStanding Pilot Only PARTPART DESCRIPTION DSI Ignition Only8000DVTFL, 6000DVTFL, 6000ARCH, SL-42DVT PARTBoth Standing Pilot and DSI Ignition PART AccessoriesBoth Standing Pilot and DSI Ignition Cont ACCESSORY