Manuals / Heat & Glo LifeStyle / Household Appliance / Indoor Fireplace

Heat & Glo LifeStyle 6000 XLT manual VENTING WITH THREE 3 90 ELBOWS, Venting with three 90 elbows

Models: 8000 DVTFL 6000 XLT 6000 ARCH 6000 DVTFL SL-42 DVT

1 46

Page 18

VENTING WITH THREE (3) 90° ELBOWS

V (FT.)	H (FT.) (8000 & 6000’s)	H (FT.) (SL-42DVT)
1' MIN. (305 mm)	6' MAX. (1.86 m)	3'	MAX. (914 mm)
2' MIN. (610 mm)	12' MAX. (3.72 m)	6'	MAX. (1.86 m)
3' MIN. (914 mm)	18' MAX. (5.58 m)	9'	MAX. (2.74 m)
4' MIN. (1.22 m)	24' MAX. (8.44 m)	12' MAX. (3.66 m)
	24' MAX. (8.44 m)	12' MAX. (3.66m)

NOTE: H + H1 MAX. 24' (8.44 m) (8000 & 6000’s)

NOTE: H + H1 MAX. 12' (3.66 m) (SL-42DVT)

V + V1 MAX. 20' (6.2 m)

NOTE: MODEL 6000 ARCH

A 12-inch length of straight vent pipe MUST be the first vent component attached to the unit.

Figure 13. Venting with three 90° elbows

Page 18

Image 18

Heat & Glo LifeStyle 6000 XLT manual VENTING WITH THREE 3 90 ELBOWS, Venting with three 90 elbows, NOTE: MODEL 6000 ARCH

Contents

Heat-N-GloFireplace Underwriters Laboratories ListedInstallers Guide 8000 DVTFL SAFETY AND WARNING INFORMATION THIS UNIT IS NOT FOR USE WITH SOLID FUELPROHIBITED Table of Contents Installation Codes Approvals and Codesand Codes High Altitude Installations Getting Started Pre-installationPreparationIntroducing the Heat-N-Glo Gas Fireplaces ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD Figure 1. Diagram of 8000DVTFL Page Figure 3. Diagram of SL-42DVT Installing the Fireplace Step Locating the FireplaceClearance Requirements COVERING DETAILS, BEFORE FRAMING Step Framing the FireplaceVERIFY FRAMING METHODS AND WALL CONSTRUCTION BEGINS Step Installing the Vent System A. Vent System Approvals DV-48D DV-36D DV-90DDV-45D DV-12D 4-inchinner pipe/6 5/8-inchouter pipe Figure 9. Vertical Venting VERTICAL VENTING V FT 40 MAX. 12.4 MNOTE MODEL 6000 ARCH NOTE: IF A 90 ELBOW IS FIRST Model 6000XLT & 8000DVTFLFOR SL-42DVT ATTACHED TO THE UNIT, THE NOTE MODEL 6000 ARCH VENTING WITH TWO 2 90 ELBOWSFigure 11. Venting with two 90 elbows H1 V H NOTE: MODEL 6000 ARCH VENTING WITH TWO 2 90 ELBOWSFigure 12. Venting with two 90 elbows H V1 V VENTING WITH THREE 3 90 ELBOWS Figure 13. Venting with three 90 elbowsNOTE: MODEL 6000 ARCH VENTING WITH THREE 3 90 ELBOWS Figure 14. Venting with three 90 elbows B. Installing Vent Components ENSURE THAT THE FIBERGLASS Figure 17. Adding Venting Components 3. Install Support BracketsTo install support brackets for horizontal runs •Place the pipe supports around the vent pipe For Horizontal Runs - Firestops are REQUIRED Figure 18. Installing Support Brackets4. Install Firestops Model DVK-01TRDand SLK-01TRDdo not need Figure 19. Hole and Vent Pipe Figure 21. Hole and New Framing Members Figure 22. Ceiling Firestop Ceiling Side C. Vent Termination Figure 23. Attic Firestop Figure 24. Round and Trapezoid Termination Caps THE VINYL PROTECTOR KIT TO THE TOP OF VINYL SIDING, IT IS NECESSARY TO INSTALLIF EXTERIOR WALLS ARE FINISHED WITH TERMINATION CAPS MAJOR U.S. BUILDING CODES on the outside of the building Roof Pitch Step Positioning Leveling, and Securing the FireplaceStep The Gas Control Systems 13 mm hook-upat the unit Step The Gas Supply LineFigure 28. Gas Controls Systems DO NOT USE AN OPEN FLAME TO CHECK FOR GAS LEAKS Pressure Step Gas Pressure RequirementsFigure 29. Gas Supply Line Natural Gas Step Wiring the Fireplace For Standing Pilot Ignition Wiring WHEN SERVICING CONTROLS. WIRING Electrical wiring must be installed by a licensedLABEL ALL WIRES PRIOR TO DISCONNECTION ERRORS CAN CAUSE IMPROPER AND Step Finishing Step Installing Trim Logs, and Ember Material Hearth Extensions Positioning the Logs Save the log instructions with this manualPlacing the Ember Material Figure 35. Glass Assembly Figure 36. Placement of the Ember Material1.Lift the trim door up and out of the unit Review safety warnings and cautions Lighting the Fireplace After the InstallationStep Before Lighting the Fireplace Step Double-checkfor faulty components TURN OFF THE GAS BEFORE SERVICING Fireplace MaintenanceMaintaining and Servicing Your Fireplace YOUR FIREPLACE Figure 37. Burner Flame Patterns Figure 38. Pilot/Ignitor Flame Patterns PART Replacement Parts and AccessoriesStanding Pilot Only PART DESCRIPTION PART DSI Ignition Only8000DVTFL, 6000DVTFL, 6000ARCH, SL-42DVT PART DESCRIPTION Both Standing Pilot and DSI Ignition ACCESSORY AccessoriesBoth Standing Pilot and DSI Ignition Cont PART