Manuals / Heat & Glo LifeStyle / Household Appliance / Indoor Fireplace

Heat & Glo LifeStyle 8000 DVTFL, SL-42 DVT, 6000 ARCH, 6000 XLT manual B. Installing Vent Components

Models: 8000 DVTFL 6000 XLT 6000 ARCH 6000 DVTFL SL-42 DVT

1 46

Download 46 pages 22.06 Kb

Page 20

B. Installing Vent Components

17

1.Apply the stove ce- ment.

2.Line up the internal beads and rotate the pipe sections clock- wise until locked.

3.Lock the vent compo- nents into place.

4.Check the seal on the rope gasket.

B. Installing Vent Components

1.Attach the First Vent Component to the Starting Collars

To attach the first vent component to the starting collars of the fireplace:

•Apply a 3/8 inch (9.5 mm) bead of stove cement around the inner pipe fireplace starting collar.

•Make sure that the fireplace rope gasket supplied with the fireplace seals between the first

vent component and the outer fireplace wrap.

•Lock the vent components into place by sliding the concentric pipe sections with four (4) equally spaced interior beads into the fireplace collar or previously installed component end with four (4) equally spaced indented sections.

•When the internal beads of each outer pipe line up, rotate the pipe section clockwise about one-quarter (1/4) turn. The vent pipe is now locked together.

•The first 90° elbow installed in the vent system of a rear venting fireplace MUST BE in a vertical posi- tion.

STARTING

COLLAR

STOVE

SEALANT

BEAD

FIRST	3/8 INCH (9.5 mm)
VENT
COMPONENT

1 INCH (25.4 mm)

Figure 15. Attaching the First Vent Component to the Starting Collars

WARNING

A 3/8 INCH (9.5 MM) BEAD OF STOVE CEMENT MUST BE PLACED AROUND THE INNER PIPE FIREPLACE STARTING COLLAR BEFORE ATTACHING THE FIRST VENT COMPONENT. FAILURE TO SEAL THIS JOINT MAY CAUSE THE FIREPLACE TO OPERATE IMPROPERLY. SEE THE DIAGRAM .

Image 20

Heat & Glo LifeStyle 8000 DVTFL, SL-42 DVT, 6000 ARCH, 6000 XLT, 6000 DVTFL manual B. Installing Vent Components

Contents

Underwriters Laboratories Listed Installers GuideHeat-N-GloFireplace 8000 DVTFL PROHIBITED SAFETY AND WARNING INFORMATIONTHIS UNIT IS NOT FOR USE WITH SOLID FUEL Table of Contents Approvals and Codes and CodesInstallation Codes High Altitude Installations Pre-installationPreparation Introducing the Heat-N-Glo Gas FireplacesGetting Started ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD Figure 1. Diagram of 8000DVTFL Page Figure 3. Diagram of SL-42DVT Clearance Requirements Installing the FireplaceStep Locating the Fireplace Step Framing the Fireplace VERIFY FRAMING METHODS AND WALLCOVERING DETAILS, BEFORE FRAMING CONSTRUCTION BEGINS Step Installing the Vent System A. Vent System Approvals DV-90D DV-45DDV-48D DV-36D DV-12D 4-inchinner pipe/6 5/8-inchouter pipe NOTE MODEL 6000 ARCH Figure 9. Vertical VentingVERTICAL VENTING V FT 40 MAX. 12.4 M Model 6000XLT & 8000DVTFL FOR SL-42DVTNOTE: IF A 90 ELBOW IS FIRST ATTACHED TO THE UNIT, THE VENTING WITH TWO 2 90 ELBOWS Figure 11. Venting with two 90 elbowsNOTE MODEL 6000 ARCH H1 V H VENTING WITH TWO 2 90 ELBOWS Figure 12. Venting with two 90 elbowsNOTE: MODEL 6000 ARCH H V1 V NOTE: MODEL 6000 ARCH VENTING WITH THREE 3 90 ELBOWSFigure 13. Venting with three 90 elbows VENTING WITH THREE 3 90 ELBOWS Figure 14. Venting with three 90 elbows B. Installing Vent Components ENSURE THAT THE FIBERGLASS 3. Install Support Brackets To install support brackets for horizontal runsFigure 17. Adding Venting Components •Place the pipe supports around the vent pipe Figure 18. Installing Support Brackets 4. Install FirestopsFor Horizontal Runs - Firestops are REQUIRED Model DVK-01TRDand SLK-01TRDdo not need Figure 19. Hole and Vent Pipe Figure 21. Hole and New Framing Members Figure 22. Ceiling Firestop Ceiling Side C. Vent Termination Figure 23. Attic Firestop Figure 24. Round and Trapezoid Termination Caps VINYL SIDING, IT IS NECESSARY TO INSTALL IF EXTERIOR WALLS ARE FINISHED WITHTHE VINYL PROTECTOR KIT TO THE TOP OF TERMINATION CAPS MAJOR U.S. BUILDING CODES on the outside of the building Roof Pitch Step The Gas Control Systems Step Positioning Leveling, and Securing theFireplace Step The Gas Supply Line Figure 28. Gas Controls Systems13 mm hook-upat the unit DO NOT USE AN OPEN FLAME TO CHECK FOR GAS LEAKS Step Gas Pressure Requirements Figure 29. Gas Supply LinePressure Natural Gas Step Wiring the Fireplace For Standing Pilot Ignition Wiring Electrical wiring must be installed by a licensed LABEL ALL WIRES PRIOR TO DISCONNECTIONWHEN SERVICING CONTROLS. WIRING ERRORS CAN CAUSE IMPROPER AND Step Finishing Step Installing Trim Logs, and Ember Material Hearth Extensions Placing the Ember Material Positioning the LogsSave the log instructions with this manual 1.Lift the trim door up and out of the unit Figure 35. Glass AssemblyFigure 36. Placement of the Ember Material Lighting the Fireplace After the Installation Step Before Lighting the Fireplace StepReview safety warnings and cautions Double-checkfor faulty components Fireplace Maintenance Maintaining and Servicing Your FireplaceTURN OFF THE GAS BEFORE SERVICING YOUR FIREPLACE Figure 37. Burner Flame Patterns Figure 38. Pilot/Ignitor Flame Patterns Replacement Parts and Accessories Standing Pilot OnlyPART PART DESCRIPTION DSI Ignition Only 8000DVTFL, 6000DVTFL, 6000ARCH, SL-42DVTPART PART DESCRIPTION Both Standing Pilot and DSI Ignition Accessories Both Standing Pilot and DSI Ignition ContACCESSORY PART