Manuals / Heat & Glo LifeStyle / Household Appliance / Indoor Fireplace

Heat & Glo LifeStyle SL-42 DVT manual Step Installing the Vent System, A. Vent System Approvals

Models: 8000 DVTFL 6000 XLT 6000 ARCH 6000 DVTFL SL-42 DVT

1 46

Download 46 pages 22.06 Kb

Page 11

Step 3

Step 3

Installing the

Vent System

A. Vent System Approvals

Models 8000DVTFL, 6000DVTFL, 6000XLT, and 6000ARCH are approved to use D-series direct vent pipe components and terminations. Model SL- 42DVT is approved to us SL-D-series components and terminations. Approved vent system components are labeled for identification. NO OTHER VENTING SYSTEMS OR COMPONENTS MAY BE USED. Detailed installation instructions are included with each vent termination kit and should be used in conjunction with this Installers Guide. The drawing below shows vent system components and terminations.

Identifying Vent Components

The vent systems installed on this gas fireplace may include one, two, or three 90° elbow assemblies. The relationships of vertical rise to horizontal run in vent configurations using 90° elbows MUST BE strictly adhered to. The rise to run relationships are shown in the venting drawings and tables. Refer to the diagrams on the next several pages.

Vent system				Vent system components
Vent system
termination kits			VERTICAL
termination kits			TERMINATION		STORM COLLAR
					STORM COLLAR
	D-SERIES				ROOF FLASHING
					ROOF FLASHING
			HORIZONTAL		HORIZONTAL PIPE
			TERMINATION		HORIZONTAL PIPE
			TERMINATION		SUPPORT
					SUPPORT
DVK-01D		DVK-TVCD
DVK-01D
DVK-02D
					PIPE LENGTH
			WALL FIRESTOP
		DVK-01TRD		CEILING	WALL BRACKET
		DVK-01TRD	90 DEGREE	FIRESTOP	WALL BRACKET
DVK-01SD		DVK-02TRD		FIRESTOP
DVK-01SD		DVK-02TRD
DVK-02SD			ELBOW
SL-D-SERIES
SLK-01D		SLK-TVCD
SLK-01D		SLK-991D
		SLK-991D
	SLK-01TRD
Figure 6.	Vent Components and Terminations

8

Image 11

Heat & Glo LifeStyle SL-42 DVT, 8000 DVTFL, 6000 ARCH, 6000 XLT Step Installing the Vent System, A. Vent System Approvals

Contents

8000 DVTFL Underwriters Laboratories ListedInstallers Guide Heat-N-GloFireplace PROHIBITED SAFETY AND WARNING INFORMATIONTHIS UNIT IS NOT FOR USE WITH SOLID FUEL Table of Contents High Altitude Installations Approvals and Codesand Codes Installation Codes ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD Pre-installationPreparationIntroducing the Heat-N-Glo Gas Fireplaces Getting Started Figure 1. Diagram of 8000DVTFL Page Figure 3. Diagram of SL-42DVT Clearance Requirements Installing the FireplaceStep Locating the Fireplace CONSTRUCTION BEGINS Step Framing the FireplaceVERIFY FRAMING METHODS AND WALL COVERING DETAILS, BEFORE FRAMING A. Vent System Approvals Step Installing the Vent System DV-12D DV-90DDV-45D DV-48D DV-36D 4-inchinner pipe/6 5/8-inchouter pipe NOTE MODEL 6000 ARCH Figure 9. Vertical VentingVERTICAL VENTING V FT 40 MAX. 12.4 M ATTACHED TO THE UNIT, THE Model 6000XLT & 8000DVTFLFOR SL-42DVT NOTE: IF A 90 ELBOW IS FIRST H1 V H VENTING WITH TWO 2 90 ELBOWSFigure 11. Venting with two 90 elbows NOTE MODEL 6000 ARCH H V1 V VENTING WITH TWO 2 90 ELBOWSFigure 12. Venting with two 90 elbows NOTE: MODEL 6000 ARCH NOTE: MODEL 6000 ARCH VENTING WITH THREE 3 90 ELBOWSFigure 13. Venting with three 90 elbows Figure 14. Venting with three 90 elbows VENTING WITH THREE 3 90 ELBOWS B. Installing Vent Components ENSURE THAT THE FIBERGLASS •Place the pipe supports around the vent pipe 3. Install Support BracketsTo install support brackets for horizontal runs Figure 17. Adding Venting Components Model DVK-01TRDand SLK-01TRDdo not need Figure 18. Installing Support Brackets4. Install Firestops For Horizontal Runs - Firestops are REQUIRED Figure 19. Hole and Vent Pipe Figure 22. Ceiling Firestop Ceiling Side Figure 21. Hole and New Framing Members Figure 23. Attic Firestop C. Vent Termination Figure 24. Round and Trapezoid Termination Caps TERMINATION CAPS VINYL SIDING, IT IS NECESSARY TO INSTALLIF EXTERIOR WALLS ARE FINISHED WITH THE VINYL PROTECTOR KIT TO THE TOP OF on the outside of the building MAJOR U.S. BUILDING CODES Roof Pitch Step The Gas Control Systems Step Positioning Leveling, and Securing theFireplace DO NOT USE AN OPEN FLAME TO CHECK FOR GAS LEAKS Step The Gas Supply LineFigure 28. Gas Controls Systems 13 mm hook-upat the unit Natural Gas Step Gas Pressure RequirementsFigure 29. Gas Supply Line Pressure For Standing Pilot Ignition Wiring Step Wiring the Fireplace ERRORS CAN CAUSE IMPROPER AND Electrical wiring must be installed by a licensedLABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING CONTROLS. WIRING Step Finishing Hearth Extensions Step Installing Trim Logs, and Ember Material Placing the Ember Material Positioning the LogsSave the log instructions with this manual 1.Lift the trim door up and out of the unit Figure 35. Glass AssemblyFigure 36. Placement of the Ember Material Double-checkfor faulty components Lighting the Fireplace After the InstallationStep Before Lighting the Fireplace Step Review safety warnings and cautions YOUR FIREPLACE Fireplace MaintenanceMaintaining and Servicing Your Fireplace TURN OFF THE GAS BEFORE SERVICING Figure 38. Pilot/Ignitor Flame Patterns Figure 37. Burner Flame Patterns PART DESCRIPTION Replacement Parts and AccessoriesStanding Pilot Only PART PART DESCRIPTION DSI Ignition Only8000DVTFL, 6000DVTFL, 6000ARCH, SL-42DVT PART Both Standing Pilot and DSI Ignition PART AccessoriesBoth Standing Pilot and DSI Ignition Cont ACCESSORY