Manuals / Heat & Glo LifeStyle / Household Appliance / Indoor Fireplace

Heat & Glo LifeStyle 8000 DVTFL, SL-42 DVT Model 6000XLT & 8000DVTFL, FOR SL-42DVT, FEET610 MM

Models: 8000 DVTFL 6000 XLT 6000 ARCH 6000 DVTFL SL-42 DVT

1 46

Download 46 pages 22.06 Kb

Page 15

Model 6000XLT & 8000DVTFL

Model 6000XLT & 8000DVTFL

VENTING WITH ONE (1) 90° ELBOW
V (FT.)	H (FT.) (8000 & 6000’s)	H (FT.) SL-42DVT
1' MIN. (305 mm)	6' MAX. (1.86 m)	3’ MAX. (914mm)
2' MIN. (610 mm)	12' MAX. (3.66 m)	6’ MAX. (1.83m)
3' MIN. (914 mm)	18' MAX. (5.58 m)	9’ MAX. (2.74m)
4' MIN. (1.22 m)	24' MAX. (8.44 m)	12’ MAX. (3.66m)
20' MAX. (6.2 m)	24' MAX. (8.44 m)	12’ MAX. (3.66m)
	(21' IN CANADA 6.3 m)
FOR SL-42DVT
NOTE: IF A 90° ELBOW IS FIRST
ATTACHED TO THE UNIT, THE
MAXIMUM HORIZONTAL RUN H IS		V
2-FEET (610 MM).		V
2-FEET (610 MM).		H
		H

NOTE: MODEL 6000 ARCH

A 12-INCH LENGTH OF STRAIGHT VENT PIPE MUST BE THE FIRST

VENT COMPONENT ATTACHED TO THE UNIT.

FOR 8000DVTFL, 6000DVTFL, 6000XLT

NOTE: IF A 90° ELBOW IS FIRST ATTACHED TO THE UNIT, THE MAXIMUM HORIZONTAL RUN H IS 3-FEET (914 MM).

H

V

Figure 10. Venting with One 90° Elbow

NOTE: For corner installations: A 6-inch (152mm) MINIMUM length of straight pipe must be first attached to the fireplace before 90O eblow. This will allow the vent pipe to clear the top standoffs.

12

Image 15

Heat & Glo LifeStyle 8000 DVTFL manual Model 6000XLT & 8000DVTFL, FOR SL-42DVT, NOTE: IF A 90 ELBOW IS FIRST, FEET610 MM

Contents

8000 DVTFL Underwriters Laboratories ListedInstallers Guide Heat-N-GloFireplace SAFETY AND WARNING INFORMATION THIS UNIT IS NOT FOR USE WITH SOLID FUELPROHIBITED Table of Contents High Altitude Installations Approvals and Codesand Codes Installation Codes ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD Pre-installationPreparationIntroducing the Heat-N-Glo Gas Fireplaces Getting Started Figure 1. Diagram of 8000DVTFL Page Figure 3. Diagram of SL-42DVT Installing the Fireplace Step Locating the FireplaceClearance Requirements CONSTRUCTION BEGINS Step Framing the FireplaceVERIFY FRAMING METHODS AND WALL COVERING DETAILS, BEFORE FRAMING A. Vent System Approvals Step Installing the Vent System DV-12D DV-90DDV-45D DV-48D DV-36D 4-inchinner pipe/6 5/8-inchouter pipe Figure 9. Vertical Venting VERTICAL VENTING V FT 40 MAX. 12.4 MNOTE MODEL 6000 ARCH ATTACHED TO THE UNIT, THE Model 6000XLT & 8000DVTFLFOR SL-42DVT NOTE: IF A 90 ELBOW IS FIRST H1 V H VENTING WITH TWO 2 90 ELBOWSFigure 11. Venting with two 90 elbows NOTE MODEL 6000 ARCH H V1 V VENTING WITH TWO 2 90 ELBOWSFigure 12. Venting with two 90 elbows NOTE: MODEL 6000 ARCH VENTING WITH THREE 3 90 ELBOWS Figure 13. Venting with three 90 elbowsNOTE: MODEL 6000 ARCH Figure 14. Venting with three 90 elbows VENTING WITH THREE 3 90 ELBOWS B. Installing Vent Components ENSURE THAT THE FIBERGLASS •Place the pipe supports around the vent pipe 3. Install Support BracketsTo install support brackets for horizontal runs Figure 17. Adding Venting Components Model DVK-01TRDand SLK-01TRDdo not need Figure 18. Installing Support Brackets4. Install Firestops For Horizontal Runs - Firestops are REQUIRED Figure 19. Hole and Vent Pipe Figure 22. Ceiling Firestop Ceiling Side Figure 21. Hole and New Framing Members Figure 23. Attic Firestop C. Vent Termination Figure 24. Round and Trapezoid Termination Caps TERMINATION CAPS VINYL SIDING, IT IS NECESSARY TO INSTALLIF EXTERIOR WALLS ARE FINISHED WITH THE VINYL PROTECTOR KIT TO THE TOP OF on the outside of the building MAJOR U.S. BUILDING CODES Roof Pitch Step Positioning Leveling, and Securing the FireplaceStep The Gas Control Systems DO NOT USE AN OPEN FLAME TO CHECK FOR GAS LEAKS Step The Gas Supply LineFigure 28. Gas Controls Systems 13 mm hook-upat the unit Natural Gas Step Gas Pressure RequirementsFigure 29. Gas Supply Line Pressure For Standing Pilot Ignition Wiring Step Wiring the Fireplace ERRORS CAN CAUSE IMPROPER AND Electrical wiring must be installed by a licensedLABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING CONTROLS. WIRING Step Finishing Hearth Extensions Step Installing Trim Logs, and Ember Material Positioning the Logs Save the log instructions with this manualPlacing the Ember Material Figure 35. Glass Assembly Figure 36. Placement of the Ember Material1.Lift the trim door up and out of the unit Double-checkfor faulty components Lighting the Fireplace After the InstallationStep Before Lighting the Fireplace Step Review safety warnings and cautions YOUR FIREPLACE Fireplace MaintenanceMaintaining and Servicing Your Fireplace TURN OFF THE GAS BEFORE SERVICING Figure 38. Pilot/Ignitor Flame Patterns Figure 37. Burner Flame Patterns PART DESCRIPTION Replacement Parts and AccessoriesStanding Pilot Only PART PART DESCRIPTION DSI Ignition Only8000DVTFL, 6000DVTFL, 6000ARCH, SL-42DVT PART Both Standing Pilot and DSI Ignition PART AccessoriesBoth Standing Pilot and DSI Ignition Cont ACCESSORY