Manuals / Heat & Glo LifeStyle / Household Appliance / Indoor Fireplace

Heat & Glo LifeStyle 6000 DVTFL Step Wiring the Fireplace, For Standing Pilot Ignition Wiring

Models: 8000 DVTFL 6000 XLT 6000 ARCH 6000 DVTFL SL-42 DVT

1 46

Download 46 pages 22.06 Kb

Page 34

Image 34

Step 8

Step 8

Wiring the

Fireplace

CAUTION

NOTE: Electrical wiring must be installed by a licensed electrician.

For Standing Pilot Ignition Wiring

Appliance Requirements

•This appliance DOES NOT require 110-120 VAC to operate.

WARNING

DO NOT CONNECT 110-120 VAC TO THE GAS CONTROL VALVE OR THE APPLIANCE WILL MALFUNCTION AND THE VALVE WILL BE DESTROYED.

Optional Accessories

Optional fan and remote control kits require that 110- 120 VAC be wired to the factory installed junction box before the fireplace is permanently installed.

Remote Wall Switch

Position the remote wall switch in the desired position on a wall. Run a maximum of 25 feet (7.8 m) or less length of 18 A.W.G. minimum wire and connect it to the fireplace ON/OFF switch pigtails.

WARNING

DO NOT CONNECT 110-120 VAC TO THE REMOTE WALL SWITCH OR THE CONTROL VALVE WILL BE DESTROYED.

LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING CONTROLS. WIRING ERRORS CAN CAUSE IMPROPER AND DANGEROUS OPERATION. VERIFY PROPER OPERATION AFTER SERVICING.

31

NOTE: MODEL SL-42DVT

DOES NOT HAVE A HI-TEMP

LIMIT SWITCH.

Figure 30. Standing Pilot Ignition Wiring Diagram

Image 34

Heat & Glo LifeStyle 6000 DVTFL, 8000 DVTFL, SL-42 DVT manual Step Wiring the Fireplace, For Standing Pilot Ignition Wiring

Contents

Heat-N-GloFireplace Underwriters Laboratories ListedInstallers Guide 8000 DVTFL THIS UNIT IS NOT FOR USE WITH SOLID FUEL SAFETY AND WARNING INFORMATIONPROHIBITED Table of Contents Installation Codes Approvals and Codesand Codes High Altitude Installations Getting Started Pre-installationPreparationIntroducing the Heat-N-Glo Gas Fireplaces ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD Figure 1. Diagram of 8000DVTFL Page Figure 3. Diagram of SL-42DVT Step Locating the Fireplace Installing the FireplaceClearance Requirements COVERING DETAILS, BEFORE FRAMING Step Framing the FireplaceVERIFY FRAMING METHODS AND WALL CONSTRUCTION BEGINS Step Installing the Vent System A. Vent System Approvals DV-48D DV-36D DV-90DDV-45D DV-12D 4-inchinner pipe/6 5/8-inchouter pipe VERTICAL VENTING V FT 40 MAX. 12.4 M Figure 9. Vertical VentingNOTE MODEL 6000 ARCH NOTE: IF A 90 ELBOW IS FIRST Model 6000XLT & 8000DVTFLFOR SL-42DVT ATTACHED TO THE UNIT, THE NOTE MODEL 6000 ARCH VENTING WITH TWO 2 90 ELBOWSFigure 11. Venting with two 90 elbows H1 V H NOTE: MODEL 6000 ARCH VENTING WITH TWO 2 90 ELBOWSFigure 12. Venting with two 90 elbows H V1 V Figure 13. Venting with three 90 elbows VENTING WITH THREE 3 90 ELBOWSNOTE: MODEL 6000 ARCH VENTING WITH THREE 3 90 ELBOWS Figure 14. Venting with three 90 elbows B. Installing Vent Components ENSURE THAT THE FIBERGLASS Figure 17. Adding Venting Components 3. Install Support BracketsTo install support brackets for horizontal runs •Place the pipe supports around the vent pipe For Horizontal Runs - Firestops are REQUIRED Figure 18. Installing Support Brackets4. Install Firestops Model DVK-01TRDand SLK-01TRDdo not need Figure 19. Hole and Vent Pipe Figure 21. Hole and New Framing Members Figure 22. Ceiling Firestop Ceiling Side C. Vent Termination Figure 23. Attic Firestop Figure 24. Round and Trapezoid Termination Caps THE VINYL PROTECTOR KIT TO THE TOP OF VINYL SIDING, IT IS NECESSARY TO INSTALLIF EXTERIOR WALLS ARE FINISHED WITH TERMINATION CAPS MAJOR U.S. BUILDING CODES on the outside of the building Roof Pitch Fireplace Step Positioning Leveling, and Securing theStep The Gas Control Systems 13 mm hook-upat the unit Step The Gas Supply LineFigure 28. Gas Controls Systems DO NOT USE AN OPEN FLAME TO CHECK FOR GAS LEAKS Pressure Step Gas Pressure RequirementsFigure 29. Gas Supply Line Natural Gas Step Wiring the Fireplace For Standing Pilot Ignition Wiring WHEN SERVICING CONTROLS. WIRING Electrical wiring must be installed by a licensedLABEL ALL WIRES PRIOR TO DISCONNECTION ERRORS CAN CAUSE IMPROPER AND Step Finishing Step Installing Trim Logs, and Ember Material Hearth Extensions Save the log instructions with this manual Positioning the LogsPlacing the Ember Material Figure 36. Placement of the Ember Material Figure 35. Glass Assembly1.Lift the trim door up and out of the unit Review safety warnings and cautions Lighting the Fireplace After the InstallationStep Before Lighting the Fireplace Step Double-checkfor faulty components TURN OFF THE GAS BEFORE SERVICING Fireplace MaintenanceMaintaining and Servicing Your Fireplace YOUR FIREPLACE Figure 37. Burner Flame Patterns Figure 38. Pilot/Ignitor Flame Patterns PART Replacement Parts and AccessoriesStanding Pilot Only PART DESCRIPTION PART DSI Ignition Only8000DVTFL, 6000DVTFL, 6000ARCH, SL-42DVT PART DESCRIPTION Both Standing Pilot and DSI Ignition ACCESSORY AccessoriesBoth Standing Pilot and DSI Ignition Cont PART