Manuals / Heat & Glo LifeStyle / Household Appliance / Indoor Fireplace

Heat & Glo LifeStyle SL-750TV-D, SL-950TV-IPI-D, SL-950TV-D, SL-550TV-D Notches Raised Flat Spots

Models: SL-750TV-D SL-950TV-IPI-D SL-550TV-D SL-550TV-IPI-D SL-750TV-IPI-D SL-950TV-D

1 54

Download 54 pages 51.66 Kb

Page 29

NOTCHES

RAISED FLAT SPOTS

3

RAISED FLAT SPOTS

LOG #3 (SRV530-718):Place log #3 on the left two grate bars using the notches in the bottom of the log. Position log parallel to log #1 and on the same line as log #2. Left edge of log should rest between grate bar and second tab.

TAB LOCATOR

4

LOG #4 (SRV2045-703):Place log #4 on top of log #1 and log #2 so that the cutouts on the bottom of log #4 ﬁt on the tab on log #1 and will ﬁt in the ﬂat spot on log #2.

TAB LOCATOR

5

LOG #5 (SRV2045-702):Place log #5 on the tab on log #1 so that the cutouts on the bottom of log #5 ﬁt onto the raised ﬂat spots on log #2.

Heat & Glo • SL-550 / 750 / 950TV-D • 2053-985 Rev. J • 4/07

29

Image 29

Heat & Glo LifeStyle SL-750TV-D, SL-950TV-IPI-D, SL-950TV-D, SL-750TV-IPI-D, SL-550TV-IPI-D Notches Raised Flat Spots

Contents

What to do if you smell gas Homeowner Reference Information Congratulations Table of Contents Glass Speciﬁcations 1Listing and Code ApprovalsBTU Speciﬁcations Models Combustible Materials Speciﬁcation High Altitude InstallationsNon-Combustible Materials Speciﬁcation Getting Started Design and Installation Considerations Negative Pressure Inspect Appliance and Components Tools and Supplies Needed Selecting Appliance Location Framing and Clearances Clearances Constructing the Appliance Chase Clearances to Mantels or other Combustibles above Appliance Mantel Projections Vent Termination Minimum Clearances Termination Locations Vent System Conﬁguration Vent Information and DiagramsVent Guidelines Minimum Vertical Feet Vertical Penetration Framing Vent Clearances and FramingPipe Clearances to Combustibles Gas and Electrical Connections Installing Outside Air Kit Damper AssemblyAppliance Preparation Proper Positioning, Leveling and Securing of a Securing and Leveling Appliance Assembly of Vent Sections Installing Vent PipeSecuring Vent Sections Attaching Vent to Firebox Fuel Conversions Gas Connection Gas InformationGas Pressures Pressure Natural Gas Propane High Altitude Installations Connecting to the Appliance Recommendation for WireIntelliﬁre Ignition System Wiring Optional Accessories Requirements Ground to Standing Pilot Ignition System Wiring Wall Switch Installation for Fan Optional Junction Box Installation Facing Material Finishing Clean the Appliance Appliance SetupAccessories Remove Shipping Materials Positioning the Logs Log Set Assembly LOGS-SL550-D Models SL-550TV-D TAB Locator Log Set Assembly LOGS-SL750-D Models SL-750TV-D, SL-950TV-D Notches Raised Flat Spots Shutter Settings Glass AssemblyScreen Mesh Grilles and Trim Before Lighting Appliance Operating InstructionsCheck Appliance Draft Before operating this appliance have a qualified technician Intelliﬁre Ignition Lighting Appliance Standing Pilot Ignition For Your Safety Read Before Lighting Instructions After Appliance is Lit Frequently Asked QuestionsInitial Break-in Procedure Standing Pilot Ignition System TroubleshootingSymptom Possible Causes Corrective Actions Symptom Possible Cause Corrective Action Troubleshooting Intelliﬁre Ignition System Symptom Possible Causes Corrective Actions Before servicing Maintaining and Servicing Appliance Inspect Maintenance Tasks Reference Materials Appliance Dimension DiagramAppliance Dimensions Table Log Set Assembly Service Parts SL-550TV-D Service Parts List SL-550TV-D, SL-550TV-IPI-D SL-750TV-D SL-750TV-D SL-750TV-D, SL-750TV-IPI-D SL-950TV-D SL-950TV-D SL-950TV-D, SL-950TV-IPI-D SL-550 / 750 / 950TV-D SL-550 / 750 / 950TV-D-IPI Limited Lifetime Warranty Heat & GLO GAS Appliance Products Limited Lifetime Warranty Do not Discard this Manual Contact Information