Manuals / Heat & Glo LifeStyle / Household Appliance / Indoor Fireplace

Heat & Glo LifeStyle SL-950TV-IPI-D Getting Started, A. Design and Installation Considerations

Models: SL-750TV-D SL-950TV-IPI-D SL-550TV-D SL-550TV-IPI-D SL-750TV-IPI-D SL-950TV-D

1 54

Download 54 pages 51.66 Kb

Page 6

2 Getting Started

2 Getting Started

A. Design and Installation Considerations

Heat & Glo B-type vent gas appliances are designed to operate with all exhaust gases expelled to the outside of the building, and combustion air pulled from the room.

CAUTION

Check building codes prior to installation.

•Installation MUST comply with local, regional, state and national codes and regulations.

•Consult local building, ﬁre ofﬁcials or authorities having jurisdiction about restrictions, installation inspection, and permits.

When planning an appliance installation, it’s necessary to determine the following information before installing:

•Where the appliance is to be installed. See Sections 3 and 4.

•The vent system conﬁguration to be used. See Sections 5 and 6.

•Gas supply piping. See Sections 7 and 9.

•Electrical wiring. See Sections 7 and 10.

•Framing and ﬁnishing details. See Sections 3, 6 and 11.

•Whether optional accessories—devices such as a fan, wall switch, or remote control—are desired. See Section 10.

WARNING

Fire Risk

Explosion Risk

Keep appliance dry.

•Water may damage controls.

•Mold or rust may cause odors.

6	Heat & Glo • SL-550 / 750 / 950TV-D • 2053-985 Rev. J • 4/07

Image 6

Heat & Glo LifeStyle SL-950TV-IPI-D, SL-950TV-D, SL-750TV-IPI-D Getting Started, A. Design and Installation Considerations

Contents

SL-950TV-D, SL-950TV-IPI-D Models SL-550TV-D, SL-550TV-IPI-DSL-750TV-D, SL-750TV-IPI-D •What to do if you smell gasHomeowner Reference Information CongratulationsSection 8: Installing Vent Pipe Table of ContentsSection 5: Vent Information and Diagrams Appliance SetupB. Glass Speciﬁcations 1Listing and Code ApprovalsA.Appliance Certiﬁcation C. BTU SpeciﬁcationsF. Combustible Materials Speciﬁcation D. High Altitude InstallationsE. Non-CombustibleMaterials Speciﬁcation Materials that are reported as passing ASTM E•Electrical wiring. See Sections 7 and A. Design and Installation Considerations2 Getting Started •Gas supply piping. See Sections 7 andB. Negative Pressure C. Tools and Supplies Needed D. Inspect Appliance and Components3 Framing and Clearances A. Selecting Appliance LocationSection B. Constructing the Appliance Chase C. ClearancesCombustibles above Appliance D. Mantel ProjectionsFigure 3.3 Clearances to Mantels or other 13mm4 Termination Locations A. Vent Termination Minimum ClearancesB. Vent System Conﬁguration 5 Vent Information and DiagramsA. Vent Guidelines ModelsFire Risk. Explosion Risk 6 Vent Clearances and Framing A. Pipe Clearances to CombustiblesC. Vertical Penetration Framing B. Gas and Electrical Connections A. Installing Outside Air Kit Damper Assembly7 Appliance Preparation HINGEC. Securing and Leveling Appliance C. Securing Vent Sections 8 Installing Vent PipeA. Assembly of Vent Sections B. Attaching Vent to FireboxC. Gas Connection 9 Gas InformationA. Fuel Conversions B. Gas PressuresHIGH ALTITUDE INSTALLATIONS C.Intelliﬁre Ignition System Wiring A. Recommendation for WireB. Connecting to the Appliance 10 Electrical InformationD. Standing Pilot Ignition System Wiring Standing Pilot Ignition Wiring DiagramFigure Connector E. Junction Box InstallationF. Wall Switch Installation for Fan Optional GRN wire11 Finishing A. Mantel ProjectionsB. Facing Material D. Accessories 12 Appliance SetupC. Clean the Appliance E.Install the RefractoryG. Positioning the Logs Log Set Assembly: LOGS-SL550-D Models: SL-550TV-D2 1 3 NOTCHESNOTCH TAB LOCATORTAB LOCATOR Models: SL-750TV-D, SL-950TV-D Log Set Assembly: LOGS-SL750-D2 4 1 3 NOTCHESRAISED FLAT SPOTS NOTCHESRAISED FLAT SPOTS TAB LOCATORI. Screen Mesh H. Glass AssemblyL. Shutter Settings J. Grilles and Trim13 Operating Instructions A. Before Lighting ApplianceB. Check Appliance Draft TO TURN OFF GAS TO APPLIANCE FOR YOUR SAFETY READ BEFORE LIGHTINGLIGHTING INSTRUCTIONS IPI C. Lighting ApplianceFOR YOUR SAFETY READ BEFORE LIGHTING LIGHTING INSTRUCTIONSStanding Pilot Ignition TO TURN OFF GAS TO APPLIANCEInitial Break-inProcedure E. Frequently Asked QuestionsD. After Appliance is Lit ISSUESymptom 14 TroubleshootingA. Standing Pilot Ignition System Possible CausesPossible Cause Troubleshooting continuedSymptom Corrective ActionPossible Causes B. Intelliﬁre Ignition SystemSymptom Corrective ActionsPossible Causes Intelliﬁre Ignition System - continuedSymptom Corrective ActionsWhen cleaning glass door 15 Maintaining and Servicing ApplianceClean Before servicingMaintenance Tasks Inspectpresent A. Appliance Dimension Diagram 16 Reference MaterialsAppliance Dimensions Table 9 8 14 B. Service PartsSL-550TV-D Log Set AssemblyAVAILABLE B. Service Parts ListSL-550TV-D TO SHIP INAVAILABLE B. Service Parts ListSL-550TV-D, SL-550TV-IPI-D TO SHIP INLog Set Assembly Service PartsSL-750TV-D Service Parts DiagramAVAILABLE Service Parts ListSL-750TV-D TO SHIP INAVAILABLE B. Service Parts ListSL-750TV-D, SL-750TV-IPI-D TO SHIP INLog Set Assembly SL-950TV-DService Parts Service Parts DiagramAVAILABLE Service Parts ListSL-950TV-D TO SHIP INAVAILABLE Service Parts ListSL-950TV-D, SL-950TV-IPI-D TO SHIP INService Parts Valve AssemblySL-550 /750 / 950TV-D Standing PilotService Parts IPI Valve AssemblySL-550 /750 / 950TV-D-IPI AVAILABLEC. Limited Lifetime Warranty LIMITED LIFETIME WARRANTYHEAT & GLO GAS APPLIANCE PRODUCTS D. Contact Information NOTESDO NOT DISCARD THIS MANUAL