Manuals / Heat & Glo LifeStyle / Household Appliance / Indoor Fireplace

Heat & Glo LifeStyle SL-750TV-IPI-D, SL-950TV-IPI-D, SL-950TV-D, SL-550TV-D Minimum Vertical Feet

Models: SL-750TV-D SL-950TV-IPI-D SL-550TV-D SL-550TV-IPI-D SL-750TV-IPI-D SL-950TV-D

1 54

Download 54 pages 51.66 Kb

Page 14

WARNING

Fire Risk. Explosion Risk.

Insulation and other combustibles must not infringe on clearances.

• ALWAYS maintain speciﬁed clearances around venting and ﬁrestop systems.

• Install ﬁrestops as speciﬁed.

Failure to keep insulation or other material away from vent pipe may cause ﬁre.

MAXIMUM HORIZONTAL 15 FEET

MINIMUM

VERTICAL

9 FEET

45 DEGREES	OFFSETS EXCEEDING
ELBOW	45 DEGREES ADAPT
	HORIZONTAL LIMITATIONS

90DEGREES ELBOW

Note: Maximum horizontal distance is 50% vertical vent height.

Figure 5.3

14	Heat & Glo • SL-550 / 750 / 950TV-D • 2053-985 Rev. J • 4/07

Image 14

Heat & Glo LifeStyle SL-750TV-IPI-D, SL-950TV-IPI-D, SL-950TV-D, SL-550TV-IPI-D, SL-550TV-D, SL-750TV-D Minimum Vertical Feet

Contents

What to do if you smell gas Congratulations Homeowner Reference Information Table of Contents BTU Speciﬁcations 1Listing and Code ApprovalsGlass Speciﬁcations Models Combustible Materials Speciﬁcation High Altitude InstallationsNon-Combustible Materials Speciﬁcation Design and Installation Considerations Getting Started Negative Pressure Tools and Supplies Needed Inspect Appliance and Components Framing and Clearances Selecting Appliance Location Constructing the Appliance Chase Clearances Mantel Projections Clearances to Mantels or other Combustibles above Appliance Termination Locations Vent Termination Minimum Clearances Vent System Conﬁguration Vent Information and DiagramsVent Guidelines Minimum Vertical Feet Vertical Penetration Framing Vent Clearances and FramingPipe Clearances to Combustibles Gas and Electrical Connections Installing Outside Air Kit Damper AssemblyAppliance Preparation Securing and Leveling Appliance Proper Positioning, Leveling and Securing of a Securing Vent Sections Installing Vent PipeAssembly of Vent Sections Attaching Vent to Firebox Gas Pressures Gas InformationFuel Conversions Gas Connection Pressure Natural Gas Propane High Altitude Installations Intelliﬁre Ignition System Wiring Recommendation for WireConnecting to the Appliance Optional Accessories Requirements Standing Pilot Ignition System Wiring Ground to Junction Box Installation Wall Switch Installation for Fan Optional Finishing Facing Material Accessories Appliance SetupClean the Appliance Remove Shipping Materials Log Set Assembly LOGS-SL550-D Models SL-550TV-D Positioning the Logs TAB Locator Log Set Assembly LOGS-SL750-D Models SL-750TV-D, SL-950TV-D Notches Raised Flat Spots Screen Mesh Glass AssemblyShutter Settings Grilles and Trim Check Appliance Draft Operating InstructionsBefore Lighting Appliance Before operating this appliance have a qualified technician Lighting Appliance Intelliﬁre Ignition For Your Safety Read Before Lighting Instructions Standing Pilot Ignition After Appliance is Lit Frequently Asked QuestionsInitial Break-in Procedure Standing Pilot Ignition System TroubleshootingSymptom Possible Causes Corrective Actions Troubleshooting Symptom Possible Cause Corrective Action Intelliﬁre Ignition System Symptom Possible Causes Corrective Actions Maintaining and Servicing Appliance Before servicing Inspect Maintenance Tasks Reference Materials Appliance Dimension DiagramAppliance Dimensions Table Service Parts Log Set Assembly Service Parts List SL-550TV-D SL-550TV-D, SL-550TV-IPI-D SL-750TV-D SL-750TV-D SL-750TV-D, SL-750TV-IPI-D SL-950TV-D SL-950TV-D SL-950TV-D, SL-950TV-IPI-D SL-550 / 750 / 950TV-D SL-550 / 750 / 950TV-D-IPI Limited Lifetime Warranty Limited Lifetime Warranty Heat & GLO GAS Appliance Products Contact Information Do not Discard this Manual