Hitachi L200 243

B–27

L200 Inverter

	Holding Registers for “A” Group Standard Functions

Func.	Name	R/W	Description		Network Data
Func.
Code				Reg.		Range	Res.
Code



A042	Manual torque boost	R/W	Can boost starting torque	004Fh		0 to 200	0.1 %
	value		between 0 and 20% above
			normal V/f curve,
A242	Manual torque boost	R/W	normal V/f curve,	0050h
A242	Manual torque boost	R/W	range is 0.0 to 20.0%	0050h
	value, 2nd motor		range is 0.0 to 20.0%
	value, 2nd motor

A043	Manual torque boost	R/W	Sets the frequency of the V/f	0051h		0 to 500	0.1 %
A043	Manual torque boost	R/W	Sets the frequency of the V/f	0051h		0 to 500	0.1 %
	frequency adjustment		breakpoint A in graph (top of
			previous page) for torque
A243	Manual torque boost	R/W	previous page) for torque	0052h
A243	Manual torque boost	R/W	boost, range is 0.0 to 50.0%	0052h				Appendix
	frequency adjustment,		boost, range is 0.0 to 50.0%


	2nd motor

A044	V/f characteristic curve	R/W	Two available V/f curves;	0053h		0, 1, 2	—
	selection		two select codes:
			00... Constant torque					B
A244	V/f characteristic curve	R/W	00... Constant torque	0054h
A244	V/f characteristic curve	R/W	01... Reduced torque	0054h
	selection, 2nd motor		01... Reduced torque
	selection, 2nd motor

A045	V/f gain setting	R/W	Sets voltage gain of the	0055h		20 to 100	1 %
			inverter, range is 20. to 100.%

A051	DC braking enable	R/W	Two options; select codes:	005Ch		0, 1	—
			00... Disable
			01... Enable

A052	DC braking frequency	R/W	The frequency at which DC	005Dh		(B082 x	0.1 Hz
	setting		braking begins,			10) to 600
			range is from the start
			frequency (B082) to 60 Hz

A053	DC braking wait time	R/W	The delay from the end of	005Eh		0, 1	—
			controlled deceleration to start
			of DC braking (motor free runs
			until DC braking begins),
			range is 0.0 to 5.0 sec.

A054	DC braking force for	R/W	Level of DC braking force,	005Fh		0 to 100	1 %
	deceleration		settable from 0 to 100%

A055	DC braking time for	R/W	Sets the duration for DC	0060h		0 to 600	0.1 sec
	deceleration		braking, range is 0.0 to 60.0
			seconds

A056	DC braking / edge or	R/W	Two options; select codes:	0061h		0, 1	—
	level detection for [DB]		00... Edge detection
	input		01... Level detection

A061	Frequency upper limit	R/W	Sets a limit on output	0062h		(A062 x	0.1 Hz
	setting		frequency less than the			10) to
			maximum frequency (A004).			(A004 x
A261	Frequency upper limit	R/W	maximum frequency (A004).	0063h		(A004 x
A261	Frequency upper limit	R/W	Range is from frequency lower	0063h		10),
	setting, 2nd motor		Range is from frequency lower			10),
	setting, 2nd motor		limit (A062) to maximum			0=disable
			limit (A062) to maximum			0=disable
			frequency (A004).			>1=enabl
			0.0.. setting is disabled			e
			>0.1 setting is enabled