1- 5
Function mode
Code Function name SJ300 Setting range Initial data
-FE/-FU/-F Note
b012 Electronic thermal level 0.2*constant current-1.20*constant current(A) Rated
Current of
inverter
b212 Electronic thermal level
(2nd motor) 0.2*constant current-1.20*constant current(A) Rated
Current of
Inverter
b312 Electronic thermal level
(3rd motor) 0.2*constant current-1.20*constant current(A) Rated
current of
inverter
b013 1st
electronic thermal
characteristic selection 00(reduced characteristic)/ 01(constant torque characteristic)/
02(free setting) 01/01/00
b213 2nd electronic thermal
characteristic selection 00(reduced characteristic)/ 01(constant torque characteristic)/
02(free setting) 01/01/00
b313 3rd electronic thermal
characteristic selection 00/(reduced characteristic)01(constant torque characteristic)/
02(free setting) 01/01/00
b015 Free electronic thermal
frequency 10.-400.(Hz) 0.
b016 Free electronic thermal
current 10.0-1000.(A) 0.0
b017 Free electronic thermal
frequency 20.-400.(Hz) 0.
b018 Free electronic thermal
current 20.0-1000. (A) 0.0
b019 Free electronic thermal
frequency 30.-400.(Hz) 0.
b020 Free electronic thermal
current 30.0-1000.(A) 0.0
b021 Overload restriction selection 00(invalid)/01(enabled on acceleration / constant speed)/
02(enabled on constant speed)/03(enabled on acceleration / constant
speed (speed increasing at regenerating mode)) 01
b022 Overload restriction level 0.50* rated current-2.00* rated current(A) <-1.80*ratede current(A)> Rated current
of Inverter
x 1.50
b023 Overload restriction limit
constant 0.10-30.00(s) 1.00
b024 Overload restriction 2
selection
00(invalid)/01(enabled on acceleration / constant speed)/
02(enabled on constant speed)/03(enabled on acceleration / constant
speed (speed increasing at regenerating mode)) 01
b025 Overload restriction level 20.50*rated current-2.00*rated current(A) <-1.80*rated current(A)> Rated current
of inverter
x1.50
b026 Overload restriction constant
20.10-30.00(s) 1.00
b031 Software lock mode selection
00(impossible to change the data except this item when SFT terminal is
ON)/01(impossible to change the data except setting frequency item
when SFT terminal is ON)/02(impossible to change the data except this
item)/
03(impossible to change the data except setting frequency item)/
10(possible to change data on operating)
01
b100
Free V/f frequency 10.- Free V/f frequency2(Hz) 0.
b101
Free V/f voltage 10.-800.0(V) 0.0
b102
Free V/f frequency 20.- Free V/f frequency3(Hz) 0.
b103
Free V/f voltage 2 0.-800.0(V) 0.0
b104
Free V/f frequency 30.- Free V/f frequency4(Hz) 0.
b105 Free V/f voltage 3 0.-800.0(V) 0.0
b106 Free V/f frequency 40.- Free V/f frequency5(Hz) 0.
b107
Free V/f voltage 4 0.-800.0(V) 0.0
b108
Free V/f frequency 50.- Free V/f frequency6(Hz) 0.
b109
Free V/f voltage 5 0.-800.0(V) 0.0
b110
Free V/f frequency 60.- Free V/f frequency7(Hz) 0.
b111
Free V/f voltage 6 0.-800.0(V) 0.0
b112
Free V/f frequency 70.-400.(Hz) 0.
b113 Free V/f voltage 7 0.-800.0(V) 0.0
C001 Intelligent input 1 setting 18
C002 Intelligent input 2 setting 16
C003 Intelligent input 3 setting 06
C004 Intelligent input 4 setting 11
C005 Intelligent input 5 setting 09
C006 Intelligent input 6 setting 03/13/03
C007 Intelligent input 7 setting 02
C008 Intelligent input 8 setting
01/(RV:Reverse is valid)/02(CF1:Multi-speed1)/ 03(CF2:Multi-speed2)/
04(CF3:Multi-speed3)/ 05(CF4:Multi-speed4)/ 06(JG:Jogging)/
07(DB:External DC braking)/ 08(SET:2nd control)/
09(2CH:two-stage adjustable speed)/ 11(FRS:Free-run)/ 12(EXT:External trip)/
13(USP:Unattended start protection)/ 14(CS:commercial change)/
15(SFT:software lock)/ 16(AT:Analog input voltage/current select)/
17(SET3:3rdcontrol)/ 18(RS:Reset inverter)/ 20(STA:3wire run)/
21(STP:3wire keep)/ 22(F/R:3wire forward/reverse)/
23(PID:PID selection valid/invalid)/ 24(PIDC:PID integrating reset)/
26(CAS:Control gain switch function)/ 27(UP:Remote control UP function)/
28(DWN:Remote control DOWN function)/29(UDC:Remote control data clear)/
31(OPE:Operating by operator select)/ 32(SF1:Multi-speed bit1)/
33(SF2:Multi-speed bit2)/ 34(SF3:Multi-speed bit3)/ 35(SF4:Multi-speed bit4)/
36(SF5:Multi speed bit5)/ 37(SF6:Multi-speed bit6)/ 38(SF7:Multi-speed bit7)/
39(OLR:Overload restriction change) / 40(TL:Torque limit select)/
41(TRQ1:Torque limit switch 1)/ 42(TRQ2:Torque limit switch 2)/
43((PPI:P/PI switch)/ 44(BOK:Braking comformation)/ 45(ORT:Orientation)/
46(LAC:LAD cancel)/ 47(PCLR:Position error clear)/
48(STAT:Permission of pulse train)/ no(NO:No assign) 01
(Note) < > indicate the setting range of 75 to 150kW

Electronic thermal
Free V/f setting
Intelligent input terminal setting
Overload limit