Hitachi L300P Series service manual

Function Mode

		Code	Function name			L300P Setting range	Initial data	N o t e
							-FE/-FU/-FR
		b021	Overload restriction			00(invalid)/01(enabled on acceleration / constant speed)/02(enabled	01
			selection			on constant speed)
							Rated
		b022	Overload restriction level			0.50* rated current-1.50* rated current(A)	current of
							inverter
	limit						x 1.20
		b023	Overload restriction limit			0.10-30.00(s)	1.00
	Overload		constant
		b024	Overload restriction 2			00(invalid)/01(valid on acceleration / constant speed)/02(valid on	01
			selection			constant speed)
							Rated
		b025	Overload restriction level 2			0.50*rated current-1.50*rated current(A)	current of
							inverter
							x1.20
		b026	Overload restriction			0.10-30.00(s)	1.00
			constant 2
						00(impossible to change the data except this item when SFT terminal
	Lock	b031	Software lock mode			is ON)/01(impossible to change the data except setting frequency	01
						item when SFT terminal is ON)/02(impossible to change the data
			selection
						except this item)/03(impossible to change the data except setting
						frequency item)/10(possible to change data on operating)
		b100	Free V/f frequency 1			0.- Free V/f frequency2(Hz)	0.
		b101	Free V/f voltage 1			0.-800.0(V)	0.0
		b102	Free V/f frequency 2			0.- Free V/f frequency3(Hz)	0.
		b103	Free V/f voltage 2			0.-800.0(V)	0.0
	setting	b104	Free V/f frequency 3			0.- Free V/f frequency4(Hz)	0.
		b105	Free V/f voltage 3			0.-800.0(V)	0.0
		b106	Free V/f frequency 4			0.- Free V/f frequency5(Hz)	0.
	V/f	b107	Free V/f voltage 4			0.-800.0(V)	0.0
		b108	Free V/f frequency 5			0.- Free V/f frequency6(Hz)	0.
	Free	b109	Free V/f voltage 5			0.-800.0(V)	0.0
		b110	Free V/f frequency 6			0.- Free V/f frequency7(Hz)	0.
		b111	Free V/f voltage 6			0.-800.0(V)	0.0
		b112	Free V/f frequency 7			0.-400.(Hz)	0.
		b113	Free V/f voltage 7			0.-800.0(V)	0.0
	setting	C001	Intelligent input 1 setting			0 1 / (RV:Reverse is valid)/02(CF1:Multi-speed1)/ 03(CF2:Multi - speed2)/	18
						04(CF3:Multi - speed3)/ 05(CF4:Multi-speed4)/ 0 6 (JG:Jogging)/
						07(DB:External DC braking)/08(SET:2nd control)/
	terminal					09(2CH:two - stage adjustable speed)/11(FRS:Free - run)/
		C002	Intelligent input 2 setting			12(EXT:External trip)/13(USP:Unattended start protection)/	16
						14(CS:commercial change)/15(SFT:software lock)/
						16(AT:Analog input voltage/current select)/18(RS:Reset inverter)/
		C003	Intelligent input 3 setting			20(STA:3wire run)/ 21(STP:3wire keep)/22(F/R:3wire forward/reverse)/	03/13/03
	input					23(PID:PID selection valid/invalid)/24(PIDC:PID integrating reset)/
						27(UP:Remote control UP function)/
	Intelligent					28(DWN:Remote control DOWN function)/
		C004	Intelligent input 4 setting			29(UDC:Remote control data clear)/31(OPE:Force operate o p e ) /	02
						32(SF1:Multi-speed bit1)/
						33(SF2:Multi-speed bit2)/34(SF3:Multi-speed bit3)/
		C005	Intelligent input 5 setting			35(SF4:Multi - speed bit4)/36(SF5:Multi speed bit5)/	01
						37(SF6:Multi-speed bit6)/38(SF7:Multi-speed bit7)/
						39(OLR:Overload restriction change)/no(NO:No assign)
		C011	Intelligent input1 a/b			00(NO)/01(NC)	00
terminalsetting			(NO/NC) selection
		C012	Intelligent input2 a/b			00(NO)/01(NC)	00
			(NO/NC) selection
	intelligent
			(NO/NC) selection
		C013	Intelligent input3 a/b			00(NO)/01(NC)	00/01/00
			(NO/NC) selection
		C014	Intelligent input4 a/b			00(NO)/01(NC)	00
Input
		C015	Intelligent input5 a/b			00(NO)/01(NC)	00
			(NO/NC) selection
		C019	Input FW a/b (NO/NC)			00(NO)/01(NC)	00
			Selection
setting		C021	Intelligent output 11 setting			00(RUN:running)/01(FA1:Frequency arrivaltype1 signal)/	01
						02(FA2:frequency arrival type2 signal)/03(OL:Overload advance
terminal		C022	Intelligent output 12 setting			notice signal)/04(OD:Output deviation for PID control)/05(AL:Alarm	00
						over)/
						signal)/06(FA3:Only setting frequency)/08( IP:On instantaneous stop/
		C026	Alarm relay output			09(UV:Under voltage)/11(RNT:RUN time over)/12(ONT:ON time	05
output						00(Output frequency)/01(Output current) /
		C027	FM selection			03(Digital output frequency)/04(Output voltage)/	00
Intelligent						05(Input electric power)/06(thermal load rate)/07(LAD frequency)
						05(Input electric power)/06(Thermal load rate)/07(LAD frequency)
		C028	AM selection			00(Output frequency)/01(Output current)/04(Output voltage)/	00
						05(Input electric power)/06(thermal load rate)/07(LAD frequency)
		C029	AMI selection			00(Output frequency)/01(Output current)/04(Output voltage)/	00
setting,		C031	Intelligent output 11 a/b			00(NO)/01(NC)	00
		C032	Intelligent output 12 a/b			00(NO)/01(NC)	00
		C036	Alarm relay output a/b			00(NO)/01(NC)	01
terminalstate	levelsetting	C040	Overload advance notice			00(On accel. And decel, constant speed)/01(Only constant speed)	01
			signal output mode
		C042	Overload	advance	notice	0.00-99.99/100.0-400.0(Hz)	Inverter
			Frequency	arrival	setting		0.00
		C041	level			0.0-2.0*rated current(A)	rated current
Output	Output		for acceleration.
			deceleration.
		C043	Arrival frequency setting for			0.00-99.99/100.0-400.0(Hz)	0.00
		C044	PID deviation setting level			0.0-100.0(%)	3.0

1- 13